# The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019, Paragraph 23: Commission Regulation (EU) No 1253/2014

Extent: E+W+S+N.I.

(1) Commission Regulation (EU) No 1253/2014 of 7 July 2014 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for ventilation units is amended as follows.
(2) In Article 1, in subparagraph 2(d), after “Council”, insert “ , as it had effect immediately before IP completion day ”.
(3) In Article 2 (definitions), at the beginning, for “For the purposes of this Regulation the following definitions shall apply:”, substitute—
“The definitions set out in the Ecodesign for Energy-Related Products Regulations 2010 apply; and for any term that is not defined in those Regulations, the definitions set out in Directive 2009/125/EC of the European Parliament and of the Council of 21 October 2009 establishing a framework for the setting of ecodesign requirements for energy-related products, as it had effect immediately before IP completion day, apply. The following definitions also apply—”.
(4) In Article 5 (conformity assessment), in paragraph 1, for the words from “Manufacturers of ventilation” to “Annex V to that Directive”, substitute—
“1 For the purposes of regulation 4(2)(a) of the Ecodesign for Energy-Related Products Regulations 2010, the procedure for assessing whether an energy-related product complies with this implementing measure is the internal design control system set out in Part 1 of Schedule 1A to the Ecodesign for Energy-Related Products Regulations 2010 or the management system for assessing conformity set out in Part 2 of Schedule 1A to those Regulations.”.
(5) For Article 6 (verification procedure for market surveillance purposes) substitute—
“When performing market surveillance checks to assess compliance with the requirements set out for RVUs in Annex 2 and for NRVUs in Annex 3 the authorities of Great Britain must apply the verification procedure described in Annex 6.”.
(6) In Article 7 (benchmarks), omit “referred to in point (2) of Part 3 of Annex 1 to Directive 2009/125/EC”.
(7) Article 8 (review) is omitted.
(8) At the end of Article 9 (entry into force), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.
(9) Annex 6 (product compliance verification by market surveillance authorities) is amended as follows—
(a) in each instance, for “Member State” or “Member States”, substitute “ Great Britain ”;
(b) for the second paragraph, substitute—
“When verifying the compliance of a product model with the requirements laid down in this Regulation, for the requirements referred to in this Annex the authorities of Great Britain must apply the following procedure—”;
(c) in subparagraph (2)(a)—
(i) for “point 2 of Annex IV to Directive 2009/125/EC (declared values)” substitute “ paragraph 1(2) of Part 1 of Schedule 1A to the Ecodesign for Energy-Related Products Regulations 2010 ”; and
(ii) for “paragraph (g) thereof”, substitute “ paragraph 1(2)(b)(vii) of Part 1 of Schedule 1A to those Regulations ”;
(d) subparagraph (6) is omitted; and
(e) in the fourth paragraph—
(i) for “6” substitute “ 5 ”; and
(ii) for “harmonised” substitute “ designated ”.

---
Source: https://www.legislation.gov.uk/uksi/2019/539/schedule/2/paragraph/23 (the official version)
Page: https://openlegislation.uk/ecodesign-for-energy-related-products-and-energy-information-amendment-eu-exit-regulations-2019/schedule-2/paragraph-23
Contains public sector information licensed under the Open Government Licence v3.0. Source: legislation.gov.uk, The National Archives.