Annex A SPECIFICATIONS FOR INTEROPERABILITYX1
United Kingdom
All specifications referred to in this table are mandatory unless they are clearly marked as ‘ informative ’ .
GLOBAL REQUIREMENTS
| The references of this column are only valid in the case of the TSI CCS-HS. | |||||
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index No | Control-command TSI paragraph reference f1 | Subject f2 | Scope f3 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 0a. | 4.1.1 | ETCS FRS | UIC ETCS FRS Version 4.29 EEIG 99E5362 Version 2.00 | ||
| 0b. | 4.1.1 | GSM-R FRS | EIRENE FRS Version 6.0 | ||
| 1 | 3.2.1 | Safety assurance. | Informative documentation: EN 50128 March 2001 | EN50126 September 1999 EN50129 February 2003 | |
| 2 | RAMS | ||||
| 2a. | 3.2.1 4.1.1 | Safety requirements | Informative documentation UNISIG SUBSET -077-V222 UNISIG SUBSET -078-V222 UNISIG SUBSET -079-V222 (2parts) UNISIG SUBSET -080-V222 (2 parts) UNISIG SUBSET -081-V222 (2 parts) UNISIG SUBSET -088-V222 (6 parts) | UNISIG SUBSET -091-V222 | EN50129 February 2003 |
| 2b. | 3.2.2e | Reliability-availability-requirements. | ERTMS/96s1266- (RAM chapter) to be used as input information. Informative documentation: EEIG 02S1266- Version 6 | Reserved | EN 50126 September 1999 |
| 2c. | 3.2b | Quality of maintenance. | The procedures against which the quality of the maintenance of control-command equipment is to be judged. | Reserved | EN 29000 and EN 29001 |
| 3 | 3.2.5.1.1 4.2.1.2d | Environmental physical conditions. | The minimum requirements upon temperature, humidity, shock, vibration etc. that Control-Command equipment shall respect for use upon the high-speed network. Informative documentation: EEIG 97S0665- Version 5, EN50125-3 October 2003 | Reserved | EN 50125-1 September 1999 and EN 50155 August 2001 |
| 4 | 3.2.5.1.2 | Electromagnetic compatibility: | |||
| 4a. | 3.2.5.1.2 4.2.1.2d | Electromagnetic compatibility | ERTMS/97s0665- to be used as input document. For the purpose of EMC, frequency bands for intentional transmission (Eurobalise, Euroloop, and GSM-R) are excluded from the specifications indicated in this index. Specific requirements for the Eurobalise air-gap are indicated in index 12a. Specific requirements for the Euroloop air-gap are indicated in index 12b. Specific requirements for GSM-R air-gap are indicated in index 12c. | Reserved | For on-board equipment: EN 50121-3-2, September 2000, Tables 4 and 6 in Clause 7. Clauses 4, 5, and 6 are applicable for testing procedures. EN 50121-3-2, September 2000, Tables 7, 8, and 9 in Clause 8. Clauses 4, 5, and 6 are applicable for testing procedures. For track-side equipment: EN 50121-4, September 2000, Clause 5. EN 50121-4, September 2000, Clause 6 |
| 4b | 3.2.5.1.2b 4.2.1.2f | The immunity characteristics of train detection systems. | To ensure that train detection systems are not perturbed by traction current. Input for European specification is contained in the report to TSI CC. | Reserved | (reserved) |
CONTROL COMMAND FUNCTIONS
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index No | Control-command TSI paragraph reference | Subject f4 | Scope f5 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 5 | Provision of cab-signalling logic and ATP logic and associated functions. | ||||
| 5a. | 4.1.1 | Normal operation. | Informative documentation: UNISIG SUBSET-050-V200, UNISIG SUBSET-076-0-V222 UNISIG SUBSET -076-2-V221 UNISIG SUBSET -076-3-V221 UNISIG SUBSET -076-4-1-V100 UNISIG SUBSET -076-4-2-V100 UNISIG SUBSET -076-5-3-V220 UNISIG SUBSET -076-5-4-V221 UNISIG SUBSET -076-6-1-V100 UNISIG SUBSET -076-6-4-V100 UNISIG SUBSET -076-6-5-V100 | UNISIG SUBSET-026- V222 UNISIG SUBSET-043-V200 UNISIG SUBSET-046-V200 UNISIG SUBSET-047-V200 UNISIG SUBSET-054-V200 UNISIG SUBSET-055- V222 UNISIG SUBSET -076-5-1-V221 UNISIG SUBSET -076-5-2-V221 UNISIG SUBSET -076-6-3-V100 UNISIG SUBSET -076-7-V100 UNISIG SUBSET -094-0-V100 | |
| 5b. | 4.1.1 | Degraded operation | The system requirements in response to failures. ERTMS/97E832 to be used as input for European specification | UNISIG SUBSET-026- V222 | |
| 6 | 4.1.1 4.1.2.2 | STM management. | The functional and physical requirements on the STM interface to the Class A system. KER compatibility is to be addressed. Informative documentation: UNISIG SUBSET-059-V200 | UNISIG SUBSET-035-V211 UNISIG SUBSET-026- V222 UNISIG SUBSET-056-V220 UNISIG SUBSET-057-V220 UNISIG SUBSET-058-V211 | |
| 7 | 4.1.1 | MMI driver interface functional requirements. | The functional specification for communication between the driver and the onboard assembly. The driver's displays states what is required for driving e.g. cab-signals, warning of intervention. It includes the input functions e.g. train characteristics, override functions, required for interoperable control-command purposes. It also includes the display of text messages. The cab-signals define the minimum range of parameters made available in the cab that together satisfy all the circumstances that could be found upon the railways of the European high-speed network and that therefore make a system common for the whole network feasible. Such parameters would be permitted speed, target speed, target distance, that are the basis of cab-signalling and ATP. Informative documentation: CENELEC WGA9D V21.DOC 12/04/2000 , CENELEC WGA9D V05 DOC 27/03/2000 , CENELEC WGA9D V11.DOC 12/04/2000 , CENELECWGA9D V06.DOC 12/01/2000 , CENELEC WGA9D V08NS.DOC 27/03/2000 and CENELEC WGA9D V04.DOC 27/03/2000 . | UNISIG SUBSET-033-V200 UNISIG SUBSET-026- V222 UNISIG SUBSET-035-V211 | |
| 8 | 4.1.1 | Odometry requirements | The functional requirements of the odometry sub-system required to support the range of performance expected of the equipment providing the Class A interfaces. Location accuracy depends on odometry and the distance between balises. The requirements for speed and distance measurements on an interoperable train. Note relation with index 6, STM | UNISIG SUBSET-041-V200 | |
| 9 | 4.1.1 | Requirements for the onboard recording of operational data | The requirements for the choice of data parameters, regularity, accuracy, validation checks for the purposes of inspecting the proper driving of the train and the behaviour of safety related systems such that the requirements of the legal authorities in all member states can be met. | UNISIG SUBSET-026- V222 UNISIG SUBSET-027-V200 | |
| 10 | r4.1.1 | Vigilance (dead man's) system requirements. | The definition of a vigilance function so that the train can operate acceptably on the European networks. Vigilance ensures that the driver is sufficiently alert (and by implication sufficiently alert to be aware of the signalling). If a timer is used, the timer can be reset by other driver actions on the train controls, traction controller, brakes, cab warning acknowledgement. It can be associated with a need to hold a lever in a given position (dead man function). The functionality required of the vigilance can be modified by the status of ATP and any cab warning system. Vigilance, ATP and cab warning systems are safety related systems in the sense that they support the driver and provide protection to the train in the event of human inadequacy. The level of safety is determined by all these systems, and they are inter-dependent in the sense that the presence or absence of one can affect the functionality of the others. The management of the safety issues is facilitated by considering these systems to be in the scope of control-command. UIC 641 is to be the basis for European Specification. | Reserved | |
| 11 | 4.1.1 4.2.1.2e | Radio. | The definition of the radio system for voice and data communication to and from the trains. | EIRENE SRS Version 14 Test requirements (to be added in the next version of this TSI) | |
INTERFACES BETWEEN ONBOARD AND TRACKSIDE ASSEMBLIES
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| The applicable Up-link and Tele-powering frequency ranges are defined in UNISIG SUBSET-036-V221. | |||||
| Index No | Control-command TSI paragraph reference | Subject f6 | Scope f7 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 12 | Data transmission interfaces - between the train and the ground. | ||||
| 12a. | 3.2.5.1.2 4.1.2.1 | Balise | Technical compatibility with some Class B systems requires the toggling function as defined in the European specifications. This is to be considered acceptable from the point of view of EMC. | UNISIG SUBSET-036-V221 UNISIG SUBSET-085-V212 | ETSI EN 300330-1, V1.3.1 (June 2001), up to and including Sub-clause 7.2 f8 . |
| 12b. | 3.2.5.1.2 4.1.2.1 | Loop | Informative documentation: UNISIG SUBSET-050-V200 | UNISIG SUBSET-043-V200 UNISIG SUBSET-044-V200 UNISIG SUBSET-045-V200 Test requirements (to be added in the next version of this TSI) | |
| 12c. | 3.2.5.1.2 4.1.2.1 | Radio | EIRENE SRS Version14 | ||
INTERFACES ONBOARD BETWEEN CONTROL-COMMAND INTEROPERABILITY CONSTITUENTS
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index No | Control-command TSI paragraph reference | Subject f9 | Scope f10 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 13 | Onboard data communication interfaces. | The data interfaces between control-command equipment supporting the cab-signalling and automatic train protection functions, and between these functions and the train. | |||
| 13a. | 4.1.2.2 | ERTMS/ETCS Euroradio | UNISIG SUBSET-026- V222 UNISIG SUBSET-034-V200 UNISIG SUBSET-047-V200 UNISIG SUBSET-037-V225 UNISIG SUBSET-093-V226 UNISIG-SUBSET-048-V200 UNISIG SUBSET-092-1-V225 UNISIG SUBSET-092-2-V225 | ||
| 13b | 4.1.2.2 | GSM-R | Informative documentation: O-2475 V1.0 | A11T6001.12 | |
| 13c. | 4.1.2.2 | Train data interface for analysis of operational data recorded onboard | The communications interface, common to the high-speed network, to the data analyser of the data stored in the control-command systems to ensure readability across all parties interested. | UNISIG SUBSET-027-V200 | |
| 13d. | 4.1.2.2 | Odometry interfaces. | ERTMS/97e267 is to be the basis for a European specification A Specification will not be available in the first step. | Reserved | |
INTERFACES AT THE TRACKSIDE BETWEEN CONTROL-COMMAND INTEROPERABILITY CONSTITUENTS
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index No | Control-command TSI paragraph reference | Subject f11 | Scope f12 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 14 | Trackside data communication Interfaces between: | ||||
| 14a. | 4.1.2.3 | ERTMS/ETCS Euroradio. | UNISIG SUBSET-049-V200 UNISIG SUBSET-026- V222 UNISIG SUBSET-037-V225 UNISIG SUBSET-092-1-V225 UNISIG SUBSET-092-2-V225 UNISIG SUBSET-093-V226 | ||
| 14b. | 4.1.2.3 | GSM-R | Informative documentation: O-2475 V1.0 | A11T6001.12 | |
| 14c. | 4.1.2.3 | Eurobalise and LEU. | UNISIG SUBSET-036-V221 UNISIG SUBSET-085-V212 | ||
| 14d. | 4.1.2.3 | Euroloop and LEU. | UNISIG SUBSET-045-V200 | ||
| 14e. | 4.1.2.3 | ERTMS/ETCS and ERTMS/ETCS (RBC-RBC-handover). | UNISIG SUBSET-039-V200 | ||
| 15 | 4.2.4 | Key management | UNISIG SUBSET-038-V200 | ||
COMPATIBILITY (NOT EMC) BETWEEN TRAINS AND TRACK-CIRCUITS
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index No | Control-command TSI paragraph reference | Subject f13 | Scope f14 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 16 | 4.2.1.2B. | Rolling stock characteristics necessary to be compatible with train-detection systems. | The specification that the rolling stock must respect in order that it will operate the train detection systems correctly. To be completed, e.g., to take into account inductivity in case of axleless wheelsets and minimum axleload. | Reserved | |
DATA INTERFACES BETWEEN CONTROL-COMMAND AND ROLLING-STOCK
| dsfds | |||||
| dsfsd | |||||
| Index No | Control-command TSI paragraph reference | Subject f15 | Scope f16 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 17 | 4.2.1.2E | Train interfaces. | To cover all data concerned by interoperability that may pass between the train and control-command equipment. | UNISIG SUBSET-034-V200 | |
CONTROL-COMMAND PERFORMANCE
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index No | Control-command TSI paragraph reference | Subject f17 | Scope f18 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 18 | 4.1.1 4.3 | Performance Required. | Annexes I and IV of Directive 96/48/EC set out performance definitions of the high-speed network. | UNISIG SUBSET-041-V200 | |
VERIFICATION REQUIREMENTS
| This is the subject addressed in the paragraph referenced in the TSI. | |||||
| This is a description of the intent of the standard required to support the TSI. | |||||
| Index number 19 through 31 are intentionally deleted. | |||||
| Index No | Control-command TSI paragraph reference | Subject f19 | Scope f20 | European specifications defining basic parameters | Other European specifications |
|---|---|---|---|---|---|
| 32 f21 | 6.2 | Onboard assembly integration requirements | This shall be sufficient to ensure that the onboard assembly will operate correctly with the trackside assemblies (subsystem-verification considering the options as indicated in the register of rolling stock). Practical running tests have to be performed after the installation of onboard control-command equipment. Special attention shall be given to electromagnetic compatibility between CC and rolling stock. | UNISIG SUBSET (reserved) | |
| 33 | 6.2 | Trackside assembly integration requirements | This shall be sufficient to ensure that the trackside assembly will operate correctly with the onboard assemblies (subsystem-verification considering the options as indicated in the register of infrastructure). | UNISIG SUBSET (reserved) | |
| 34 | Table 6.1 Table 6.2 | Installation requirements | The engineering rules that apply when installing the control-command assembly onboard and trackside respectively. | UNISIG SUBSET-040-V200 | |
| 35 | Glossary of terms and abbreviations | UNISIG SUBSET-023-V200 | |||
Annotations
Editorial notes
Footnotes
- f1
-
The references of this column are only valid in the case of the TSI CCS-HS.
- f2
-
This is the subject addressed in the paragraph referenced in the TSI.
- f3
-
This is a description of the intent of the standard required to support the TSI.
- f4
-
This is the subject addressed in the paragraph referenced in the TSI.
- f5
-
This is a description of the intent of the standard required to support the TSI.
- f6
-
This is the subject addressed in the paragraph referenced in the TSI.
- f7
-
This is a description of the intent of the standard required to support the TSI.
- f8
-
The applicable Up-link and Tele-powering frequency ranges are defined in UNISIG SUBSET-036-V221.
- f9
-
This is the subject addressed in the paragraph referenced in the TSI.
- f10
-
This is a description of the intent of the standard required to support the TSI.
- f11
-
This is the subject addressed in the paragraph referenced in the TSI.
- f12
-
This is a description of the intent of the standard required to support the TSI.
- f13
-
This is the subject addressed in the paragraph referenced in the TSI.
- f14
-
This is a description of the intent of the standard required to support the TSI.
- f15
-
dsfds
- f16
-
dsfsd
- f17
-
This is the subject addressed in the paragraph referenced in the TSI.
- f18
-
This is a description of the intent of the standard required to support the TSI.
- f19
-
This is the subject addressed in the paragraph referenced in the TSI.
- f20
-
This is a description of the intent of the standard required to support the TSI.
- f21
-
Index number 19 through 31 are intentionally deleted.