{
  "url": "https://openlegislation.uk/eu-regulation-2012-392/annex-V",
  "json_url": "https://openlegislation.uk/eu-regulation-2012-392/annex-V.json",
  "legislation": "eur/2012/392",
  "legislation_title": "Commission Delegated Regulation (EU) No 392/2012 of 1 March 2012 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labelling of household tumble driers (Text with EEA relevance)",
  "legislation_url": "https://openlegislation.uk/eu-regulation-2012-392",
  "path": "annex/V",
  "kind": "annex",
  "number": "V",
  "heading": "Product compliance verification by market surveillance authorities",
  "text": "The verification tolerances set out in this Annex relate only to the verification of the measured parameters by Great Britain authorities and shall not be used by the supplier as an allowed tolerance to establish the values in the technical documentation. The values and classes on the label or in the product fiche shall not be more favourable for the supplier than the values reported in the technical documentation.\nWhen verifying the compliance of a product model with the requirements laid down in this Delegated Regulation, for the requirements referred to in this Annex, the authorities of the Great Britain shall apply the following procedure:\n(1)The Great Britain authorities shall verify one single unit of the model.\n(2)The model shall be considered to comply with the applicable requirements if:\n(a)the values given in the technical documentation pursuant to Article 5(b) of Directive 2010/30/EU (declared values), and, where applicable, the values used to calculate these values, are not more favourable for the supplier than the corresponding values given in the test reports pursuant to point (iii) of the abovementioned Article; and\n(b)the values published on the label and in the product fiche are not more favourable for the supplier than the declared values, and the indicated energy efficiency class is not more favourable for the supplier than the class determined by the declared values; and\n(c)when the Great Britain authorities test the unit of the model, the determined values (the values of the relevant parameters as measured in testing and the values calculated from these measurements) comply with the respective verification tolerances as given in Table 1.\n(3)If the results referred to in points 2(a) or (b) are not achieved, the model and all models that have been listed as equivalent household tumble drier models in the supplier's technical documentation shall be considered not to comply with this Delegated Regulation.\n(4)If the result referred to in point 2(c) is not achieved, the Great Britain authorities shall select three additional units of the same model for testing. As an alternative, the three additional units selected may be of one or more different models that have been listed as equivalent models in the supplier's technical documentation.\n(5)The model shall be considered to comply with the applicable requirements if for these three units, the arithmetical mean of the determined values complies with the respective tolerances given in Table 1.\n(6)If the result referred to in point 5 is not achieved, the model and all models that have been listed as equivalent household tumble drier models in the supplier's technical documentation shall be considered not to comply with this Delegated Regulation.\n(7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\nGreat Britain authorities must use measurement procedures which take into account the generally recognised, state-of-the-art, reliable, accurate and reproducible measurement methods, and must use the measurement and calculation methods set out in Annex 7.\nThe Great Britain authorities shall only apply the verification tolerances that are set out in Table 1 and shall only use the procedure described in points 1 to 6 for the requirements referred to in this Annex. No other tolerances, such as those set out in designated standards or in any other measurement method, shall be applied.\nTable 1\nVerification tolerances\nParameters\nVerification tolerances\nWeighted annual energy consumption ( AE C )\nThe determined value shall not exceed the declared value of AE C by more than 6 %.\nWeighted energy consumption ( E t )\nThe determined value shall not exceed the declared value of E t by more than 6 %.\nWeighted condensation efficiency ( C t )\nThe determined value shall not be less than the declared value of C t by more than 6 %.\nWeighted programme time ( T t )\nThe determined value shall not exceed the declared value of T t by more than 6 %.\nPower consumption in off mode and left-on mode ( P o and P l )\nThe determined values of power consumption P o and P l of more than 1,00 W shall not exceed the declared values of P o and P l by more than 6 %. The determined value of power consumption P o and P l of less than or equal to 1,00 W shall not exceed the declared values of P o and P l by more than 0,10 W.\nDuration of the left-on mode ( T l )\nThe determined value shall not exceed the declared value of T l by more than 6 %.\nSound power level, L WA\nThe determined value shall not exceed the declared value of L WA .",
  "extent": "E+W+S+N.I.",
  "status": null,
  "version": "current",
  "annotations": [
    {
      "type": "F",
      "label": "F1",
      "text": "Substituted by Commission Delegated Regulation (EU) 2017/254 of 30 November 2016 amending Delegated Regulations (EU) No 1059/2010, (EU) No 1060/2010, (EU) No 1061/2010, (EU) No 1062/2010, (EU) No 626/2011, (EU) No 392/2012, (EU) No 874/2012, (EU) No 665/2013, (EU) No 811/2013, (EU) No 812/2013, (EU) No 65/2014, (EU) No 1254/2014, (EU) 2015/1094, (EU) 2015/1186 and (EU) 2015/1187 with regard to the use of tolerances in verification procedures (Text with EEA relevance)."
    },
    {
      "type": "F",
      "label": "F2",
      "text": "Words in Annex 5 substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 5 para. 6(9)(a) (as amended by S.I. 2020/1528, regs. 1(2), 6(1)(2)(c)(vi)); 2020 c. 1, Sch. 5 para. 1(1)"
    },
    {
      "type": "F",
      "label": "F3",
      "text": "Annex 5 point (7) omitted (31.12.2020) by virtue of The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 5 para. 6(9)(b); 2020 c. 1, Sch. 5 para. 1(1)"
    },
    {
      "type": "F",
      "label": "F4",
      "text": "Words in Annex 5 substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 5 para. 6(9)(c) (as amended by S.I. 2020/1528, regs. 1(2), 6(3)(4)(e)(vi)); 2020 c. 1, Sch. 5 para. 1(1)"
    },
    {
      "type": "F",
      "label": "F5",
      "text": "Word in Annex 5 substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 5 para. 6(9)(d)(i); 2020 c. 1, Sch. 5 para. 1(1)"
    },
    {
      "type": "F",
      "label": "F6",
      "text": "Word in Annex 5 substituted (31.12.2020) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 (S.I. 2019/539), reg. 1(3), Sch. 5 para. 6(9)(d)(ii); 2020 c. 1, Sch. 5 para. 1(1)"
    }
  ],
  "outstanding_effects": [],
  "provenance": {
    "source": "legislation.gov.uk",
    "source_url": "https://www.legislation.gov.uk/eur/2012/392/annex/V",
    "retrieved_at": "2026-11-01T14:49:26.945744+00:00"
  },
  "licence": "Open Government Licence v3.0",
  "licence_url": "https://www.nationalarchives.gov.uk/doc/open-government-licence/version/3/",
  "attribution": "Contains public sector information licensed under the Open Government Licence v3.0. Source: legislation.gov.uk, The National Archives."
}