# Commission Regulation (EU) 2017/2400 of 12 December 2017 implementing Regulation (EC) No 595/2009 of the European Parliament and of the Council as regards the determination of the CO2 emissions and fuel consumption of heavy-duty vehicles and amending Directive 2007/46/EC of the European Parliament and of the Council and Commission Regulation (EU) No 582/2011 (Text with EEA relevance), Division 3.10.1.1

Extent: E+W+S+N.I.

The air drag pre-processing tool accepts datasets as recorded during the constant speed test in case the following validity criteria are met:
i.. the average vehicle speed is inside the criteria as defined in 3.5.2
ii.. the ambient temperature is inside the range as described in 3.2.2. This criterion is checked by the air drag pre-processing tool based on the ambient temperature measured on the vehicle.
iii.. the proving ground temperature is in the range as described in 3.2.3
iv.. valid average wind speed conditions according to point 3.2.5 item i
v.. valid gust wind speed conditions according to point 3.2.5 item ii
vi.. valid average yaw angle conditions according to point 3.2.5 item iii
vii.. stability criteria for vehicle speed met:
Low speed test:
v lms,avrg − 0,5 km ∕ h ≤ v lm,avrg ≤ v lms,avrg + 0,5 km ∕ h where:
vlms,avrg average of vehicle speed per measurement section [km/h]
vlm,avrg central moving average of vehicle speed with Xms seconds time base [km/h]
Xms time needed to drive 25 m distance at actual vehicle speed [s]
High speed test:
v hms,avrg − 0,3 km ∕ h ≤ v hm,avrg ≤ v hms,avrg + 0,3 km ∕ h where:
vhms,avrg average of vehicle speed per measurement section [km/h]
vhm,avrg 1 s central moving average of vehicle speed [km/h]
viii.. stability criteria for vehicle torque met:
Low speed test:
T lms,avrg − T grd × 0,7 ≤ T lm,avrg − T grd ≤ T lms,avrg − T grd × 1,3 T grd = F grd,avrg × r dyn,avrg where:
Tlms,avrg average of Tsum per measurement section
Tgrd average torque from gradient force
Fgrd,avrg average gradient force over measurement section
rdyn,avrg average effective rolling radius over measurement section (formula see item ix.) [m]
Tsum TL+TR ; sum of corrected torque values left and right wheel [Nm]
Tlm,avrg central moving average of Tsum with Xms seconds time base
Xms time needed to drive 25 m distance at actual vehicle speed [s]
High speed test
T hms,avrg − T grd × 0,8 ≤ T hm,avrg − T grd ≤ T hms,avrg − T grd × 1,2 where:
Thms,avrg average of Tsum per measurement section [Nm]
Tgrd average torque from gradient force (see Low speed test) [Nm]
Tsum TL+TR ; sum of corrected torque values left and right wheel [Nm]
Thm,avrg 1 s central moving average of Tsum [Nm]
ix.. valid heading of the vehicle passing a measurement section (< 10° deviation from target heading applicable for low speed test, high speed test and misalignment test)
x.. driven distance inside measurement section calculated from the calibrated vehicle speed does not differ from target distance by more than 3 meters (applicable for low speed test and high speed test)
xi.. plausibility check for engine speed or cardan speed whichever is applicable passed:
Engine speed check for high speed test:
30 × i gear × i axle × v hms,avrg − 0,3 3,6 r dyn,ref,HS × π × 1 − 0,02 ≤ n eng, 1 s ≤ 30 × i gear × i axle × v hms,avrg + 0,3 3,6 r dyn,ref,HS × π × 1 + 0,02
r dyn,avrg = 30 × i gear × i axle × v hms,avrg 3,6 n eng,avrg × π
r dyn,ref,HS = 1 n ∑ j = 1 n r dyn,avrg,j
where:
i gear transmission ratio of the gear selected in high speed test [-]
i axle axle transmission ratio [-]
v hms,avrg average vehicle speed (high speed measurement section) [km/h]
n eng,1s 1 s central moving average of engine speed (high speed measurement section) [rpm]
n eng,avrg average engine speed (high speed measurement section) [rpm]
r dyn,avrg average effective rolling radius for a single high speed measurement section [m]
r dyn,ref,HS reference effective rolling radius calculated from all valid high speed measurement sections (number = n) [m]
Engine speed check for low speed test:
30 × i gear × i axle × v lms,avrg − 0,5 3,6 r dyn,ref,LS 1 ∕ LS 2 × π × 1 − 0,02 ≤ n eng,float ≤ 30 × i gear × i axle × v lms,avrg + 0,5 3,6 r dyn,ref,LS 1 ∕ LS 2 × π × 1 + 0,02
r dyn,avrg = 30 × i gear × i axle × v lms,avrg 3,6 n eng,avrg × π
r dyn,ref,LS 1 ∕ LS 2 = 1 n ∑ j = 1 n r dyn,avrg,j
where:
i gear transmission ratio of the gear selected in low speed test [-]
i axle axle transmission ratio [-]
v lms,avrg average vehicle speed (low speed measurement section) [km/h]
n eng,float central moving average of engine speed with X ms seconds time base (low speed measurement section) [rpm]
n eng,avrg average engine speed (low speed measurement section) [rpm]
X ms time needed to drive 25 metre distance at low speed [s]
r dyn,avrg average effective rolling radius for a single low speed measurement section [m]
r dyn,ref,LS1/LS2 reference effective rolling radius calculated from all valid measurement sections for low speed test 1 or low speed test 2 (number = n) [m]
The plausibility check for cardan speed is performed in an analogue way with n eng,1s replaced by n card,1s (1 s central moving average of cardan speed in the high speed measurement section) and n eng,float replaced by n card,float (moving average of cardan speed with X ms seconds time base in the low speed measurement section) and i gear set to a value of 1.
xii.. the particular part of the measurement data was not marked as ‘invalid’ in the air drag pre-processing tool input file.

---
Source: https://www.legislation.gov.uk/eur/2017/2400/annex/VIII/division/3/division/3.10/division/3.10.1/division/3.10.1.1 (the official version)
Page: https://openlegislation.uk/eu-regulation-2017-2400/annex-VIII/division-3/division-3.10/division-3.10.1/division-3.10.1.1
Contains public sector information licensed under the Open Government Licence v3.0. Source: legislation.gov.uk, The National Archives.

