# Commission Implementing Regulation (EU) 2018/986 of 3 April 2018 amending Implementing Regulation (EU) 2015/504 as regards the adaptation of the administrative provisions for the approval and market surveillance of agricultural and forestry vehicles to Stage V emission limits (Text with EEA relevance), Annex I

Extent: E+W+S+N.I.

Annex I to Implementing Regulation (EU) 2015/504 is amended as follows:
(1) in the list of appendices, the row relating to Appendix 10 is replaced by the following:
‘
10
Model information document relating to EU type-approval of electro-magnetic compatibility of electrical/electronic sub-assemblies as a component/STU
’
(2) Part A is amended as follows:
(a) the following point 1.4 is inserted:
‘1.4.
For engines, the information folder and the information document required in Annex I to Commission Implementing Regulation (EU) 2017/656 shall be provided.’;
(b) point 2 is amended as follows:
(i) in the template of the information folder sheet, entry 2.5.2 is deleted;
(ii) in the explanatory notes relating to the information folder sheet, explanatory note (5) is replaced by the following
‘(5)
For engines, indicate the engine type designation or, in case of engine types within an engine family, the Family Type (FT) in accordance with point 4 of Part B of Annex I to Commission Implementing Regulation (EU) 2017/656.’;
(3) Part B is amended as follows:
(a) in point 3.1, Table 1-1 is amended as follows:
(i) List I is replaced by the following:
Commission Delegated Regulation (EU) 2018/985 of 12 February 2018 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council as regards environmental and propulsion unit performance requirements for agricultural and forestry vehicles and their engines and repealing Commission Delegated Regulation (EU) 2015/96 (OJ L 182; 18.7.2018, p. 1)’;
‘LIST I — Environmental and propulsion unit performance requirements
Appendix
System or component/separate technical unit (STU)
Commission Delegated Regulation (EU) 2018/985Annex number
As amended by and/or at the stage of implementation
1
System: installation of an engine/engine family
I
2
System: external sound level
II
3
Component/STU: engine/engine family
I
(ii) in List II, row 10 is replaced by the following
‘
10
Component/STU: electro-magnetic compatibility of electrical / electronic sub-assemblies
XV
’
(b) point 4.2 is replaced by the following:
‘4.2.
For those subjects referred to in Annex I to Regulation (EU) No 167/2013 whose approvals have been granted in accordance with Regulation (EU) 2016/1628 of the European Parliament and of the Council, Regulation (EC) No 595/2009 of the European Parliament and of the Council or the UNECE regulations referred to in Article 49 of Regulation (EU) No 167/2013 (UNECE approvals), or are based on complete test reports issued on the basis of the OECD standard Codes as an alternative to the test reports drawn up under that Regulation and the delegated acts adopted pursuant to it, the manufacturer shall supply the information required in point 5 only if it is not already provided in the correspondent approval certificate and/or test report. However, the information referred to in the certificate of conformity (Annex III to this Regulation) shall be supplied in any case.’;
(c) point 5 is amended as follows:
(i) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(ii) entries 2.5 to 2.5.4.2 are deleted;
(iii) entries 5.2 to 5.5 are deleted;
(iv) entries 6 to 8.22.4.2 are replaced by the following:
‘6.
ESSENTIAL CHARACTERISTICS OF THE ENGINE
6.1.7.
Category and sub-category of the engine (7): …
6.2.1.
Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (4): …
6.2.2.
Ignition Type: Compression ignition/spark ignition (4)
6.2.3.1.
Cylinders' number: … and configuration (26):
6.2.8.
Fuel
6.2.8.1.
Fuel Type (9): …
6.2.8.3.
List of additional fuels, fuel mixtures or emulsions compatible with use by the engine declared by the manufacturer in accordance with point 1.4 of Annex I to Delegated Regulation (EU) 2017/654 (provide reference to recognised standard or specification): …
6.3.2.1.
Declared rated speed: … rpm
6.3.2.1.2.
Declared rated net power: … kW
6.3.2.2.
Maximum power speed: … rpm
6.3.2.2.2.
Maximum net power: … kW
6.3.6.4.
Engine total swept volume: … cm3 ’;
(v) entry 10.4.2 is replaced by the following:
‘10.4.2.
Description and/or drawing of the elements of the exhaust system that are not part of the engine: …’;
(vi) entries 11.1 to 11.2.3 are replaced by the following:
‘11.1.
Brief description and schematic drawing of the vehicle drive-train and its control system (transmission ratio change system, clutch control or any other element of drive-train): …
11.2.
Transmission
11.2.1.
Brief description and schematic drawing of transmission ratio change system(s) and its control: …
11.2.2.
Diagram and or drawing of the power transmission: …
11.2.3.
Type of power transmission: Gear (including planetary gear sets) / belt / hydrostatic / electric / other (4) (if other, specify: …)’;
(vii) entry 11.2.8 is replaced by the following:
‘11.2.8.
Type of transmission ratio change system: Mechanical (gear change) / Double clutch (gear change) / Semi-automatic (gear change) / Automatic (gear change) / Continuously Variable Transmission/ hydrostatic / not applicable / other (4) (if other, specify: …)’;
(viii) entry 43.2 is replaced by the following:
‘43.2.
Specifications of the vehicle with respect to the control circuits of the pneumatic, hydraulic and/or electric control lines of the braking system(s) and a list of the supported messages and parameters: …’;
(ix) entries 43.5 and 43.5.1 are replaced by the following:
‘43.5.
Braking transmission (on towing vehicle)
43.5.1.
Braking transmission of the service braking system on towing vehicle: mechanical/pneumatic/hydraulic/hydrostatic/without power assistance/power-assisted/fully powered transmission (4)’;
(x) entry 43.5.3 is replaced by the following:
‘43.5.3.
Locking of left and right braking controls: yes/no (4)’;
(xi) entry 43.6 is replaced by the following:
‘43.6.
Towed vehicle braking control devices (on towing vehicle)’;
(xii) entries 43.6.2 to 43.6.5 are deleted.
(xiii) the following entries 43.6.2 to 43.7.3.2.1 are inserted:
‘43.6.2.
Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …
43.6.2.1.
Pneumatic connection type: Two lines/None (4)
43.6.2.1.1.
Pneumatic supply pressure (two lines): … kPa
43.6.2.1.2.
Electrical control line: yes/no (4)
43.6.2.2.
Hydraulic connection type: Single line / Two lines / None (4)
43.6.2.2.1.
Hydraulic supply pressure: Single line: … kPa Two lines: … kPa
43.6.2.2.2.
Presence of ISO 7638:2003 connector (15): yes/no (4)
43.7.
Towed vehicle braking devices (on towed vehicle)
43.7.1.
Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/ Inertia / None (4)
43.7.2.
Towed vehicle-brake actuating device: Drum / Disc / Other (4)
43.7.2.1.
Description and characteristics: …
43.7.3.
Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …
43.7.3.1.
Pneumatic connection type: Two lines/None (4)
43.7.3.1.1.
Electrical control line: yes/no (4)
43.7.3.2.
Hydraulic connection type: Two lines / None (4)
43.7.3.2.1.
Presence of ISO 7638:2003 connector (15): yes/no (4)’;
(4) Appendix 1 is amended as follows:
(a) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(b) entries 2.5 to 2.5.4.2 are deleted;
(c) entries 5.2 to 5.5 are deleted;
(d) entries 6 to 8.22.4.2 are replaced by the following:
‘6.
ESSENTIAL CHARACTERISTICS OF THE ENGINE
6.1.7.
Category and sub-category of the engine (7):
6.2.1.
Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (4): …
6.2.2.
Ignition Type: Compression ignition/spark ignition (4)
6.2.3.1.
Cylinders' number: … and configuration (26):
6.2.8.
Fuel
6.2.8.1.
Fuel Type (9):
6.2.8.3.
List of additional fuels, fuel mixtures or emulsions compatible with use by the engine declared by the manufacturer in accordance with point 1.4 of Annex I to Delegated Regulation (EU) 2017/654 (provide reference to recognised standard or specification): …
6.3.2.1.
Declared rated speed: … rpm
6.3.2.1.2.
Declared rated net power: … kW
6.3.2.2.
Maximum power speed: … rpm
6.3.2.2.2.
Maximum net power: … kW
6.3.6.4.
Engine total swept volume: … cm3 ’;
(5) Appendix 2 is amended as follows:
(a) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(b) entries 2.5 to 2.5.4.2 are deleted;
(c) entries 5.2 to 5.5 are deleted;
(d) the following entries 6 to 6.3.6.4 are inserted before entry 10:
‘6.
ESSENTIAL CHARACTERISTICS OF THE ENGINE
6.1.7.
Category and sub-category of the engine (7):
6.2.1.
Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (4): …
6.2.2.
Ignition Type: Compression ignition/spark ignition (4)
6.2.3.1.
Cylinders' number: … and configuration (26):
6.3.2.1.
Declared rated speed: … rpm
6.3.2.1.2.
Declared rated net power: … kW
6.3.2.2.
Maximum power speed: … rpm
6.3.2.2.2.
Maximum net power: … kW
6.3.6.4.
Engine total swept volume: … cm3 ’;
(e) the following entries 11 to 11.4 are added:
‘11.
DRIVE-TRAIN AND CONTROL (13)
11.1.
Brief description and schematic drawing of the vehicle drive-train and its control system (transmission ratio change system, clutch control or any other element of drive-train): …
11.2.
Transmission
11.2.1.
Brief description and schematic drawing of transmission ratio change system(s) and its control: …
11.2.2.
Diagram and or drawing of the power transmission: …
11.2.3.
Type of power transmission: Gear (including planetary gear sets) / belt / hydrostatic / electric / other (4) (if other, specify: …)
11.2.4.
Brief description of the electrical/electronic components (if any): …
11.2.5.
Location relative to the engine: …
11.2.6.
Method of control: …
11.2.7.
Transfer box: with/without (4)
11.2.8.
Type of transmission ratio change system: Mechanical (gear change) / Double clutch (gear change) / Semi-automatic (gear change) / Automatic (gear change) / Continuously Variable Transmission/ hydrostatic / not applicable / other (4) (if other, specify: …)
11.3.
Clutch (if any)
11.3.1
Brief description and schematic drawing of the clutch and its control system:
11.3.2
Maximum torque conversion:
11.4.
Gear ratios
Continuously variable transmission
Gear
Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions)
Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions)
Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions)
Total gear ratios
Ratio (engine speed/vehicle speed) for manual transmission only
Maximum for CVT
1
2
3
…
Minimum for CVT
Reverse
1
…
’
(6) Appendix 3 is amended as follows:
(a) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(b) entries 2.5 to 2.5.4.2 are deleted;
(c) entries 5.2 to 5.5 are deleted;
(d) entries 6 to 8.22.4.2 are replaced by the following:
‘6.
ESSENTIAL CHARACTERISTICS OF THE ENGINE
6.1.7.
Category and sub-category of the engine (7):
6.2.1.
Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (4): …
6.2.2.
Ignition Type: Compression ignition/spark ignition (4)
6.2.3.1.
Cylinders' number: … and configuration (26):
6.2.8.
Fuel
6.2.8.1.
Fuel Type (9): …
6.2.8.3.
List of additional fuels, fuel mixtures or emulsions compatible with use by the engine declared by the manufacturer in accordance with point 1.4 of Annex I to Delegated Regulation (EU) 2017/654 (provide reference to recognised standard or specification): …
6.3.2.1.
Declared rated speed: … rpm
6.3.2.1.2.
Declared rated net power: … kW
6.3.2.2.
Maximum power speed: … rpm
6.3.2.2.2.
Maximum net power: … kW
6.3.6.4.
Engine total swept volume: … cm3 ’;
(7) in Appendix 4, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(8) in Appendix 5, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(9) in Appendix 6, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(10) in Appendix 7, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(11) in Appendix 8, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(12) in Appendix 9, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(13) Appendix 10 is amended as follows:
(a) the title is replaced by the following:
‘ Appendix 10
Model information document relating to EU type-approval of electro-magnetic compatibility of electrical/electronic sub-assemblies as a component/STU ’;
(b) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(14) in Appendix 11, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(15) in Appendix 12, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(16) in Appendix 13, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(17) in Appendix 14, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(18) Appendix 15 is amended as follows:
(a) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(b) entries 5.2 to 5.4 are deleted;
(c) entries 6 to 7.1.1 are replaced by the following:
‘6.
ESSENTIAL CHARACTERISTICS OF THE ENGINE
6.1.7.
Category and sub-category of the engine (7): …
6.2.1.
Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (4): …
6.2.2.
Ignition Type: Compression ignition/spark ignition (4)
6.2.3.1.
Cylinders' number: … and configuration (26):
6.3.2.1.
Declared rated speed: … rpm
6.3.2.1.2.
Declared rated net power: … kW
6.3.2.2.
Maximum power speed: … rpm
6.3.2.2.2.
Maximum net power: … kW
6.3.6.4.
Engine total swept volume: … cm3 ’;
(d) entries 11.1 to 11.2.3 are replaced by the following:
‘11.1.
Brief description and schematic drawing of the vehicle drive-train and its control system (transmission ratio change system, clutch control or any other element of drive-train): …
11.2.
Transmission
11.2.1.
Brief description and schematic drawing of transmission ratio change system(s) and its control: …
11.2.2.
Diagram and or drawing of the power transmission: …
11.2.3.
Type of power transmission: Gear (including planetary gear sets) / belt / hydrostatic / electric / other (4) (if other, specify: …)’;
(e) entry 11.2.8 is replaced by the following:
‘11.2.8.
Type of transmission ratio change system: Mechanical (gear change) / Double clutch (gear change) / Semi-automatic (gear change) / Automatic (gear change) / Continuously Variable Transmission/ hydrostatic / not applicable / other (4) (if other, specify: …)’;
(f) entry 43.2 is replaced by the following:
‘43.2.
Specifications of the vehicle with respect to the control circuits of the pneumatic, hydraulic and/or electric control lines of the braking system(s) and a list of the supported messages and parameters: …’;
(g) entries 43.5 and 43.5.1 are replaced by the following:
‘43.5.
Braking transmission (on towing vehicle)
43.5.1.
Braking transmission of the service braking system on towing vehicle: mechanical/pneumatic/hydraulic/hydrostatic/without power assistance/power-assisted/fully powered transmission (4)’;
(h) entries 43.5.3 and 43.6 are replaced by the following:
‘43.5.3.
Locking of left and right braking controls: yes/no (4)
43.6.
Towed vehicle braking control devices (on towing vehicle)’;
(i) entries 43.6.2 to 43.6.5 are replaced by the following entries 43.6.2 to 43.7.3.2.1:
‘43.6.2.
Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …
43.6.2.1.
Pneumatic connection type: Two lines/None (4)
43.6.2.1.1.
Pneumatic supply pressure (two lines): … kPa
43.6.2.1.2.
Electrical control line: yes/no (4)
43.6.2.2.
Hydraulic connection type: Single line / Two lines / None (4)
43.6.2.2.1.
Hydraulic supply pressure: Single line: … kPa Two lines: … kPa
43.6.2.2.2.
Presence of ISO 7638:2003 connector (15): yes/no (4)
43.7.
Towed vehicle braking devices (on towed vehicle)
43.7.1.
Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/ Inertia / None (4)
43.7.2.
Towed vehicle-brake actuating device: Drum / Disc / Other (4)
43.7.2.1.
Description and characteristics: …
43.7.3.
Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …
43.7.3.1.
Pneumatic connection type: Two lines/None (4)
43.7.3.1.1.
Electrical control line: yes/no (4)
43.7.3.2.
Hydraulic connection type: Two lines / None (4)
43.7.3.2.1.
Presence of ISO 7638:2003 connector (15): yes/no (4)’;
(19) Appendix 16 is amended as follows:
(a) entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(b) the following entries 6 to 6.3.6.4 are inserted before entry 48:
‘6.
ESSENTIAL CHARACTERISTICS OF THE ENGINE
6.1.7.
Category and sub-category of the engine (7): …
6.2.1.
Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (4): …
6.2.2.
Ignition Type: Compression ignition/spark ignition (4)
6.2.3.1.
Cylinders' number: … and configuration (26):
6.3.2.1.
Declared rated speed: … rpm
6.3.2.1.2.
Declared rated net power: … kW
6.3.2.2.
Maximum power speed: … rpm
6.3.2.2.2.
Maximum net power: … kW
6.3.6.4.
Engine total swept volume: … cm3 ’;
(c) the following entries 11 to 11.4 are inserted before entry 48:
‘11.
DRIVE-TRAIN AND CONTROL (13)
11.1.
Brief description and schematic drawing of the vehicle drive-train and its control system (transmission ratio change system, clutch control or any other element of drive-train): …
11.2.
Transmission
11.2.1.
Brief description and schematic drawing of transmission ratio change system(s) and its control: …
11.2.2.
Diagram and or drawing of the power transmission: …
11.2.3.
Type of power transmission: Gear (including planetary gear sets) / belt / hydrostatic / electric / other (4) (if other, specify: …)
11.2.4.
Brief description of the electrical/electronic components (if any): …
11.2.5.
Location relative to the engine: …
11.2.6.
Method of control: …
11.2.7.
Transfer box: with/without (4)
11.2.8.
Type of transmission ratio change system: Mechanical (gear change) / Double clutch (gear change) / Semi-automatic (gear change) / Automatic (gear change) / Continuously Variable Transmission/ hydrostatic / not applicable / other (4) (if other, specify: …)
11.3.
Clutch (if any)
11.3.1
Brief description and schematic drawing of the clutch and its control system:
11.3.2
Maximum torque conversion:
11.4.
Gear ratios
Continuously variable transmission
Gear
Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions)
Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions)
Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions)
Total gear ratios
Ratio (engine speed/vehicle speed) for manual transmission only
Maximum for CVT
1
2
3
…
Minimum for CVT
Reverse
1
…
’
(20) in Appendix 17, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(21) in Appendix 18, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(22) in Appendix 19, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(23) in Appendix 20, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(24) in Appendix 21, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(25) in Appendix 22, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(26) in Appendix 23, entry 2.2 is replaced by the following:
‘2.2.
Type (6): …’;
(27) the explanatory notes relating to the information document are amended as follows:
(a) explanatory notes (6) and (7) are replaced by the following:
‘(6)
For engines, indicate the engine type designation or, in case of engine types within an engine family, the Family Type (FT) in accordance with point 4 of Part B of Annex I to Commission Implementing Regulation (EU) 2017/656.
(7)
Indicate the category and sub-category of the engine in accordance with Article 4 and Annex I to Regulation (EU) 2016/1628’;
(b) explanatory note (9) is replaced by the following:
‘(9)
Indicate the fuel type by the following codes:
B5 Diesel (non-road gas-oil)
E85 Ethanol
ED95 Ethanol for dedicated compression ignition engines
E10 Petrol
NG Natural gas/Biomethane
LPG Liquid Petroleum Gas
O (…) Other (specify)
The Sub Fuel type by the following codes (only for Natural gas/Biomethane):
U Universal fuel — high calorific fuel (H-gas) and low calorific fuel (L-gas)
RH Restricted fuel — high calorific fuel (H-gas)
RL Restricted fuel — low calorific fuel (L-gas)
LNG Fuel specific
The fuelling arrangement by the following codes:
L Liquid-fuel only
G Gaseous-fuel only
D1A Dual-fuel type 1A
D1B Dual-fuel type 1B
D2A Dual-fuel type 2A
D2B Dual-fuel type 2B
D3B Dual-fuel type 3B’;
(c) explanatory note (26) is replaced by the following:
‘(26)
Indicate the layout of the cylinders by the following codes:
LI in line
V in V
O opposed
S single
R radial
O (…) other (specify)’;
(d) explanatory notes (12), (24), (29), (39), (40) and (56) are deleted.

---
Source: https://www.legislation.gov.uk/eur/2018/986/annex/I (the official version)
Page: https://openlegislation.uk/eu-regulation-2018-986/annex-I
Contains public sector information licensed under the Open Government Licence v3.0. Source: legislation.gov.uk, The National Archives.