# Commission Delegated Regulation (EU) 2020/1749 of 7 October 2020 amending Council Regulation (EC) No 428/2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items, Division: Test, Inspection and Production Equipment

Extent: E+W+S+N.I.

1B001Equipment for the production or inspection of "composite" structures or laminates specified in 1A002 or "fibrous or filamentary materials" specified in 1C010, as follows, and specially designed components and accessories therefor:
a.. Filament winding machines, of which the motions for positioning, wrapping and winding fibres are coordinated and programmed in three or more ‘primary servo positioning’ axes, specially designed for the manufacture of "composite" structures or laminates, from "fibrous or filamentary materials";
b.. ‘Tape-laying machines’, of which the motions for positioning and laying tape are coordinated and programmed in five or more ‘primary servo positioning’ axes, specially designed for the manufacture of "composite" airframe or ‘missile’ structures;
Note:
In 1B001.b., ‘missile’ means complete rocket systems and unmanned aerial vehicle systems.
Technical Note:
For the purposes of 1B001.b., ‘tape-laying machines’ have the ability to lay one or more ‘filament bands’ limited to widths greater than 25,4 mm and less than or equal to 304,8 mm, and to cut and restart individual ‘filament band’ courses during the laying process.
c.. Multidirectional, multidimensional weaving machines or interlacing machines, including adapters and modification kits, specially designed or modified for weaving, interlacing or braiding fibres, for "composite" structures;
Technical Note:
For the purposes of 1B001.c., the technique of interlacing includes knitting.
d.. Equipment specially designed or adapted for the production of reinforcement fibres, as follows:
1.. Equipment for converting polymeric fibres (such as polyacrylonitrile, rayon, pitch or polycarbosilane) into carbon fibres or silicon carbide fibres, including special equipment to strain the fibre during heating;
2.. Equipment for the chemical vapour deposition of elements or compounds, on heated filamentary substrates, to manufacture silicon carbide fibres;
3.. Equipment for the wet-spinning of refractory ceramics (such as aluminium oxide);
4.. Equipment for converting aluminium containing precursor fibres into alumina fibres by heat treatment;
e.. Equipment for producing prepregs specified in 1C010.e. by the hot melt method;
f.. Non-destructive inspection equipment specially designed for "composite" materials, as follows:
1.. X-ray tomography systems for three dimensional defect inspection;
2.. Numerically controlled ultrasonic testing machines of which the motions for positioning transmitters or receivers are simultaneously coordinated and programmed in four or more axes to follow the three dimensional contours of the component under inspection;
g.. ‘Tow-placement machines’, of which the motions for positioning and laying tows are coordinated and programmed in two or more ‘primary servo positioning’ axes, specially designed for the manufacture of "composite" airframe or ‘missile’ structures.
Technical Note:
For the purposes of 1B001.g., ‘tow-placement machines’ have the ability to place one or more ‘filament bands’ having widths less than or equal to 25,4 mm, and to cut and restart individual ‘filament band’ courses during the placement process.
1B002Equipment designed to produce metal alloy powder or particulate materials, and having all of the following:
a.. Specially designed to avoid contamination; and
b.. Specially designed for use in one of the processes specified in 1C002.c.2.
1B003Tools, dies, moulds or fixtures, for "superplastic forming" or "diffusion bonding" titanium, aluminium or their alloys, specially designed for the manufacture of any of the following:
a.. Airframe or aerospace structures;
b.. "Aircraft" or aerospace engines; or
c.. Specially designed components for structures specified in 1B003.a. or for engines specified in 1B003.b.
1B101Equipment, other than that specified in 1B001, for the "production" of structural composites as follows; and specially designed components and accessories therefor:
a.. Filament winding machines or fibre placement machines, of which the motions for positioning, wrapping and winding fibres can be coordinated and programmed in three or more axes, designed to fabricate composite structures or laminates from "fibrous or filamentary materials", and coordinating and programming controls;
b.. Tape-laying machines of which the motions for positioning and laying tape and sheets can be coordinated and programmed in two or more axes, designed for the manufacture of composite airframe and "missile" structures;
c.. Equipment designed or modified for the "production" of "fibrous or filamentary materials" as follows:
1.. Equipment for converting polymeric fibres (such as polyacrylonitrile, rayon or polycarbosilane) including special provision to strain the fibre during heating;
2.. Equipment for the vapour deposition of elements or compounds on heated filament substrates;
3.. Equipment for the wet-spinning of refractory ceramics (such as aluminium oxide);
d.. Equipment designed or modified for special fibre surface treatment or for producing prepregs and preforms specified in entry 9C110.
Note:
1B101.d. includes rollers, tension stretchers, coating equipment, cutting equipment and clicker dies.
1B102Metal powder "production equipment", other than that specified in 1B002, and components as follows:
a.. Metal powder "production equipment" usable for the "production", in a controlled environment, of spherical, spheroidal or atomised materials specified in 1C011.a., 1C011.b., 1C111.a.1., 1C111.a.2. or in the Military Goods Controls.
b.. Specially designed components for "production equipment" specified in 1B002 or 1B102.a.
1B115Equipment, other than that specified in 1B002 or 1B102, for the production of propellant and propellant constituents, as follows, and specially designed components therefor:
a.. "Production equipment" for the "production", handling or acceptance testing of liquid propellants or propellant constituents specified in 1C011.a., 1C011.b., 1C111 or in the Military Goods Controls;
b.. "Production equipment" for the "production", handling, mixing, curing, casting, pressing, machining, extruding or acceptance testing of solid propellants or propellant constituents specified in 1C011.a., 1C011.b., 1C111 or in the Military Goods Controls.
Note:
1B115.b. does not control batch mixers, continuous mixers or fluid energy mills. For the control of batch mixers, continuous mixers and fluid energy mills see 1B117, 1B118 and 1B119.
1B116Specially designed nozzles for producing pyrolitically derived materials formed on a mould, mandrel or other substrate from precursor gases which decompose in the 1 573 K (1 300°C) to 3 173 K (2 900°C) temperature range at pressures of 130 Pa to 20 kPa.
1B117Batch mixers having all of the following, and specially designed components therefor:
a.. Designed or modified for mixing under vacuum in the range of zero to 13,326 kPa:
b.. Capable of controlling the temperature of the mixing chamber;
c.. A total volumetric capacity of 110 litres or more; and
d.. At least one ‘mixing/kneading shaft’ mounted off centre.
1B118Continuous mixers having all of the following, and specially designed components therefor:
a.. Designed or modified for mixing under vacuum in the range of zero to 13,326 kPa;
b.. Capable of controlling the temperature of the mixing chamber;
c.. any of the following,:
1.. Two or more mixing/kneading shafts; or
2.. All of the following:
a.. A single rotating and oscillating shaft with kneading teeth/pins; and
b.. Kneading teeth/pins inside the casing of the mixing chamber.
1B119Fluid energy mills usable for grinding or milling substances specified in 1C011.a., 1C011.b., 1C111 or in the Military Goods Controls, and specially designed components therefor.
1B201Filament winding machines, other than those specified in 1B001 or 1B101, and related equipment, as follows:
a.. Filament winding machines having all of the following characteristics:
1.. Having motions for positioning, wrapping, and winding fibres coordinated and programmed in two or more axes;
2.. Specially designed to fabricate composite structures or laminates from "fibrous or filamentary materials"; and
3.. Capable of winding cylindrical tubes with an internal diameter between 75 and 650 mm and lengths of 300 mm or greater;
b.. Coordinating and programming controls for the filament winding machines specified in 1B201.a.;
c.. Precision mandrels for the filament winding machines specified in 1B201.a.
1B225Electrolytic cells for fluorine production with an output capacity greater than 250 g of fluorine per hour.
1B226Electromagnetic isotope separators designed for, or equipped with, single or multiple ion sources capable of providing a total ion beam current of 50 mA or greater.
1B228Hydrogen-cryogenic distillation columns having all of the following characteristics:
a.. Designed for operation with internal temperatures of 35 K (– 238 °C) or less;
b.. Designed for operation at an internal pressure of 0,5 to 5 MPa;
c.. Constructed of either:
1.. Stainless steel of the Society of Automotive Engineers International (SAE) 300 series with low sulphur content and with an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; or
2.. Equivalent materials which are both cryogenic and hydrogen (H2)-compatible; and
d.. With internal diameters of 30 cm or greater and ‘effective lengths’ of 4 m or greater.
1B230Pumps capable of circulating solutions of concentrated or dilute potassium amide catalyst in liquid ammonia (KNH2/NH3), having all of the following characteristics:
a.. Airtight (i.e., hermetically sealed);
b.. A capacity greater than 8,5 m3/h; and
c.. Either of the following characteristics:
1.. For concentrated potassium amide solutions (1 % or greater), an operating pressure of 1,5 to 60 MPa; or
2.. For dilute potassium amide solutions (less than 1 %), an operating pressure of 20 to 60 MPa.
1B231Tritium facilities or plants, and equipment therefor, as follows:
a.. Facilities or plants for the production, recovery, extraction, concentration, or handling of tritium;
b.. Equipment for tritium facilities or plants, as follows:
1.. Hydrogen or helium refrigeration units capable of cooling to 23 K (– 250 °C) or less, with heat removal capacity greater than 150 W;
2.. Hydrogen isotope storage or hydrogen isotope purification systems using metal hydrides as the storage or purification medium.
1B232Turboexpanders or turboexpander-compressor sets having both of the following characteristics:
a.. Designed for operation with an outlet temperature of 35 K (– 238 °C) or less; and
b.. Designed for a throughput of hydrogen gas of 1 000 kg/h or greater.
1B233Lithium isotope separation facilities or plants, and systems and equipment therefor, as follows:
a.. Facilities or plants for the separation of lithium isotopes;
b.. Equipment for the separation of lithium isotopes based on the lithium-mercury amalgam process, as follows:
1.. Packed liquid-liquid exchange columns specially designed for lithium amalgams;
2.. Mercury or lithium amalgam pumps;
3.. Lithium amalgam electrolysis cells;
4.. Evaporators for concentrated lithium hydroxide solution;
c.. Ion exchange systems specially designed for lithium isotope separation, and specially designed components therefor;
d.. Chemical exchange systems (employing crown ethers, cryptands, or lariat ethers), specially designed for lithium isotope separation, and specially designed components therefor.
1B234High explosive containment vessels, chambers, containers and other similar containment devices designed for the testing of high explosives or explosive devices and having both of the following characteristics:
a.. Designed to fully contain an explosion equivalent to 2 kg of trinitrotoluene (TNT) or greater; and
b.. Having design elements or features enabling real time or delayed transfer of diagnostic or measurement information.
1B235Target assemblies and components for the production of tritium as follows:
a.. Target assemblies made of or containing lithium enriched in the lithium-6 isotope specially designed for the production of tritium through irradiation, including insertion in a nuclear reactor;
b.. Components specially designed for the target assemblies specified in 1B235.a.

---
Source: https://www.legislation.gov.uk/eur/2020/1749/annex/I/division/3/division/2 (the official version)
Page: https://openlegislation.uk/eu-regulation-2020-1749/annex-I/division-3/division-2
Contains public sector information licensed under the Open Government Licence v3.0. Source: legislation.gov.uk, The National Archives.