# The Traffic Signs Regulations and General Directions 2002, Regulation 56: Cones, delineators and cylinders

Extent: E+W+S

(1) In this regulation—
“cone” means the sign shown in diagram 7101.1;
“delineator” means the sign shown in diagram 7102;
“cylinder” means the sign shown in diagram 7103.
(2) A cone shall consist of a conically shaped device—
(a) the base of which—
(i) is of any single colour; and
(ii) is a polygon, having not more than eight sides, which would be contained wholly within a circle with a diameter of three quarters of the height of the cone; and
(b) which, subject to paragraph (15), conforms to British Standard BS EN 13422:2004+A1:2009 or to a corresponding EEA Standard.
(3) The part of a cone coloured white shall, subject to paragraph (5), be illuminated with white retroreflecting material and the part coloured red may be illuminated with red retroreflecting material.
(4) Information about the ownership of a cone may be moulded—
(a) into the base in characters not more than 80 mm high in the same colour as the base;
(b) into the conical body in characters not more than 40 mm high in the same colour as that body; or
(c) as mentioned in both sub-paragraphs (a) and (b).
(5) Information about the manufacture of a cone, required to comply with British Standard BS EN 13422:2004+A1:2009 or a corresponding EEA Standard and occupying an area not exceeding 30 square centimetres, may be indicated on the part coloured white in characters not exceeding 5 millimetres in height, leaving at least 90% of the remaining area of white colour illuminated with white retroreflecting material.
(6) A rotating device may be mounted on top of a cone and—
(a) that device shall—
(i) be red and not reflectorised; and
(ii) display one or more signs shown in either diagram 560 or diagram 561; and
(b) those signs shall be coloured amber, intermittently whilst rotating and constantly whilst static.
(7) A delineator shall consist of a flat device—
(a) of which the side intended to be exposed to traffic is coloured as shown in diagram 7102 and the reverse side is either so coloured or coloured only grey or only red;
(b) which conforms to British Standard BS 8442:2006 or to a corresponding EEA Standard;
(c) of which the base is of any single colour, except that a reflectorised white line 100 millimetres wide at an angle of not more than 60 degrees to the road surface may be marked on one side of the base at right angles to the face of the delineator.
(8) The white part of a delineator shall, subject to paragraph (10), be illuminated with white retroreflecting material and the red part (except on the reverse side when that side is coloured only red) may be illuminated with red retroreflecting material.
(9) Information about the ownership of a delineator may be moulded into the base in characters not more than 80 mm high and in the same colour as the base.
(10) Information about the manufacture of a delineator, required in order to comply with British Standard BS EN 13422:2004+A1:2009 or a corresponding EEA Standard and occupying an area not exceeding 30 square centimetres, may be indicated on the part coloured white in characters not exceeding 5 millimetres in height, leaving at least 90% of the remaining area of white colour illuminated with white retroreflecting material.
(11) A cylinder shall consist of a cylindrically shaped device which, subject to paragraph (15), conforms to British Standard BS EN 13422:2004+A1:2009 or to a corresponding EEA Standard.
(12) The white part of a cylinder shall, subject to paragraph (14), be illuminated with white retroreflecting material and the part coloured red may be illuminated with red retroreflecting material.
(13) Information about the ownership of a cylinder may be moulded into the lower of the two red parts in red characters not more than 40 mm high.
(14) Information about the manufacture of a cylinder, required in order to comply with British Standard BS EN 13422:2004+A1:2009 or a corresponding EEA Standard and occupying an area not exceeding 30 square centimetres, may be indicated on the part coloured white in characters not exceeding 5 millimetres in height, leaving at least 90% of the remaining area of white colour illuminated with white retroreflecting material.
(15) In relation to each aspect of performance specified in column (2) of an item in the Table, a cone or cylinder shall comply with—
(a) the requirement or test specification of British Standard BS EN 13422:2004+A1:2009 specified in column (3) of the item; or
(b) an equivalent requirement or test specification specified in a corresponding EEA Standard.
Table
(1)
Item
(2)
Aspect of performance
(3)
Requirement or test specification and class
1.
Daylight chromaticity co-ordinates and luminance factors
Retroreflective material:
Class LB in Table 2
Non-retroreflective exterior surfaces:
Table 3.A
Non-retroreflective interior surfaces:
Table 3.B
2.
Coefficient of retroreflection
Dry conditions:
Class R1B or R2B in Table 4.B
Wet conditions:
Class WT 1 in Table 6
3.
Height and minimum weight (cones)
Class W3 in Table 1.

---
Source: https://www.legislation.gov.uk/uksi/2002/3113/regulation/56 (the official version)
Page: https://openlegislation.uk/traffic-signs-regulations-and-general-directions-2002/regulation-56
Contains public sector information licensed under the Open Government Licence v3.0. Source: legislation.gov.uk, The National Archives.