OpenLegislation

Commission Regulation (EU) No 1229/2012 of 10 December 2012 amending Annexes IV and XII to Directive 2007/46/EC of the European Parliament and of the Council establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles (Framework Directive) (Text with EEA relevance)

EU Regulation No 1229/2012 · Adopted 10 December 2012 · Extends to United Kingdom

Original text. legislation.gov.uk does not revise this item, so later amendments are not shown here. Changes made to it are listed under each provision when known.

Commission Regulation (EU) No 1229/2012

of 10 December 2012

amending Annexes IV and XII to Directive 2007/46/EC of the European Parliament and of the Council establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles (Framework Directive)

(Text with EEA relevance)

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Directive 2007/46/EC of the European Parliament and of the Council of 5 September 2007 establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles (Framework Directive)f1, and in particular Article 39(2) and (3) thereof,

Whereas:

(1)

Directive 2007/46/EC establishes a harmonised framework containing the administrative provisions and general technical requirements for all new vehicles. In particular it includes the regulatory acts laying down the technical requirements with which vehicles have to comply in order to be granted EC vehicle type-approval.

(2)

Part 1 of Annex IV to Directive 2007/46/EC contains a list of regulatory acts for EC type-approval of vehicles produced in unlimited series. Directive 2007/46/EC has been amended several times and that list has accordingly been updated.

(3)

Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended thereforf2, provides for the repeal of several Directives. The repealed Directives have been replaced by corresponding United Nations Economic Commission for Europe (UNECE) Regulations and by Commission Regulations. Those changes should be reflected in Annex IV to Directive 2007/46/EC.

(4)

It is essential to adapt the requirements for EC type-approval of small series in order to ensure that manufacturers who produce small series of vehicles may continue to have access to the internal market. For such purposes, it is necessary to adopt simplified measures to reduce the cost required by the type-approval process whereas at the same time ensuring a high level of road safety and protection of the environment.

(5)

Since N1 vehicles exhibit construction features similar to those of M1 vehicles, it is also appropriate to lay down harmonised technical requirements for vehicles of category N1 in order to allow such vehicles produced in small series to access the internal market.

(6)

It is essential that the requirements laid down in Appendix 1 to Annex IV to Directive 2007/46/EC apply to all new vehicles. However, sufficient time should be given to manufacturers to allow them to adapt their vehicles to the new requirements.

(7)

Sections 1 and 2 of Part A of Annex XII to Directive 2007/46/EC include quantitative limits for the purposes of EC type-approval of small series. It is appropriate, when extending EC type-approval of small series to vehicles of category N1, to introduce a quantitative limit for vehicles of that category. Likewise, given the purpose of EC type-approval, namely to foster access to the internal market, the number of vehicles of category N1 that may benefit from national type-approval pursuant to Article 23 of Directive 2007/46/EC should be restricted to the necessary minimum. Therefore, the quantity of those vehicles should also be laid down.

(8)

Annexes IV and XII to Directive 2007/46/EC should therefore be amended accordingly.

(9)

The measures provided for in this Regulation are in accordance with the opinion of the Technical Committee — Motor Vehicles,

HAS ADOPTED THIS REGULATION:

Annotations to the whole text

Footnotes

f1

OJ L 263, 9.10.2007, p. 1.

f2

OJ L 200, 31.7.2009, p. 1.

Contents

  1. 1Article 1
  2. 2Article 2
  3. 3Article 3
  4. Signature
  5. Annex Annex

1

Annexes IV and XII to Directive 2007/46/EC are amended in accordance with the Annex to this Regulation.

2

EC type-approval of small series granted before 1 November 2012 shall cease to be valid on 31 October 2016. National authorities shall consider certificates of conformity for vehicles to be no longer valid for the purposes of Article 26(1) of Directive 2007/46/EC, unless the type-approvals concerned have been updated to the requirements of Appendix 1 to Annex IV to Directive 2007/46/EC.

3

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

However, point (1)(b) of the Annex shall apply in accordance with the dates set out therein.

Signature

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 10 December 2012.

For the Commission

The President

José Manuel Barroso

Directive 2007/46/EC is amended as follows:

  1. (1)

    Annex IV is amended as follows:

    1. (a)

      Part I is replaced by the following:

      ‘PART I

      Regulatory acts for EC type-approval of vehicles produced in unlimited series

      For vehicles with a reference mass not exceeding 2 610 kg. At the manufacturer’s request, may apply to vehicles with a reference mass not exceeding 2 840 kg.

      In case of vehicles equipped with a LPG or CNG installation, a vehicle type-approval in accordance with UNECE Regulation No 67 or UNECE Regulation No 110 is required.

      The fitting of an electronic stability control (“ESC”) system is required in accordance with Article 12 of Regulation (EC) No 661/2009. Therefore, the requirements set out in Annex 21 to UNECE Regulation 13 shall be complied with for the purposes of EC type-approval of new types of vehicles as well as for the registration, sale and entry into service of new vehicles. The implementation dates set out in Article 13 of Regulation (EC) No 661/2009 shall apply instead of the dates set out in UNECE Regulation No 13.

      The fitting of an ESC system is required in accordance with Article 12 of Regulation (EC) No 661/2009. Therefore, the requirements set out in Part A of Annex 9 to UNECE Regulation No 13-H shall be complied with for the purposes of EC type-approval of new types of vehicles as well as for the registration, sale and entry into service of new vehicles. The implementation dates set out in Article 13 Regulation (EC) No 661/2009 shall apply instead of the dates set out in UNECE Regulation No 13-H.

      1. (4A)

        If fitted, the protective device shall fulfil the requirements of UNECE Regulation No 18.

      1. (4B)

        This Regulation applies to seats not falling within the scope of UNECE Regulation No 80.

      Vehicles of this category shall be fitted with a suitable windscreen defrosting and demisting device.

      Vehicles of this category shall be fitted with a suitable windscreen washing and wiping devices.

      In case of vehicles equipped with an electric power train, a vehicle type-approval in accordance with UNECE Regulation No 85 is required.

      For vehicles with a reference mass exceeding 2 610 kg and which did not benefit from the possibility offered in note (1).

      For vehicles with a reference mass exceeding 2 610 kg which are not type-approved (at the manufacturer’s request and provided their reference mass does not exceed 2 840 kg) under Regulation (EC) No 715/2007.

      For other options, see Article 2 of Regulation (EC) No 595/2009.

      1. (9A)

        Applies only where such vehicles are fitted with equipment covered by UNECE Regulation No 64. Tyre pressure monitoring system for M1 vehicles applies on a compulsory basis in accordance with Article 9(2) of Regulation (EC) No 661/2009.

      Applies only to vehicles equipped with coupling(s).

      Applies to vehicles with a technically permissible maximum laden mass not exceeding 2,5 tonnes.

      Only applicable to vehicles where the “Seating Reference Point (‘R’ point)” of the lowest seat is not more than 700 mm above the ground level.

      Applies only when the manufacturer applies for type-approval of vehicles intended for the transport of dangerous goods.

      Applies only for vehicles of category N1, class I as described in the first table in point 5.3.1.4 of Annex I to Directive 70/220/EEC.

      At the request of the manufacturer, a type-approval may be granted under this item, as an alternative to obtaining type-approvals under items 3A, 3B, 4A, 5A, 6A, 6B, 7A, 8A, 9A, 9B, 10A, 12A, 13A, 13B, 14A, 15A, 15B, 16A, 17A, 17B, 18A, 19A, 20A, 21A, 22A, 22B, 22C, 23A, 24A, 25A, 25B, 25C, 25D, 25E, 25F, 26A, 27A, 28A, 29A, 30A, 31A, 32A, 33A, 34A, 35A, 36A, 37A, 38A, 42A, 43A, 44A, 45A, 46A, 46B, 46C, 46D, 46E, 47A, 48A, 49A, 50A, 50B, 51A, 52A, 52B, 53A, 54A, 56A, 57A and 64 to 70.

      Explanatory notes:

      X Regulatory act applicable.

      Note: The series of amendments of the UNECE Regulations which apply on a compulsory basis are listed in Annex IV to Regulation (EC) No 661/2009. Series of amendments adopted subsequently are accepted as an alternative.

      ItemSubjectRegulatory actApplicability
      M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
      1Permissible sound levelDirective 70/157/EECXXXXXX
      2Emissions (Euro 5 and 6) light duty vehicles/access to informationRegulation (EC) No 715/2007Xf1 X X X
      3Fuel tanks/rear protective devicesDirective 70/221/EECXf2 X X X X X XXXX
      3APrevention of fire risks (liquid fuel tanks)

      Regulation (EC) No 661/2009

      UNECE Regulation No 34

      XXXXXXXXXX
      3BRear underrun protective devices (RUPDs) and their installation; rear underrun protection (RUP)

      Regulation (EC) No 661/2009

      UNECE Regulation No 58

      XXXXXXXXXX
      4Rear registration plate spaceDirective 70/222/EECXXXXXXXXXX
      4ASpace for mounting and fixing rear registration plates

      Regulation (EC) No 661/2009

      Regulation (EU) No 1003/2010

      XXXXXXXXXX
      5Steering effortDirective 70/311/EECXXXXXXXXXX
      5ASteering equipment

      Regulation (EC) No 661/2009

      UNECE Regulation No 79

      XXXXXXXXXX
      6Door latches and hingesDirective 70/387/EECXXXX
      6AVehicle access and manoeuvrability

      Regulation (EC) No 661/2009

      Regulation (EU) No 130/2012

      XXXXXX
      6BDoor latches and door retention components

      Regulation (EC) No 661/2009

      UNECE Regulation No 11

      XX
      7Audible warningDirective 70/388/EECXXXXXX
      7AAudible warning devices and signals

      Regulation (EC) No 661/2009

      UNECE Regulation No 28

      XXXXXX
      8Indirect vision devicesDirective 2003/97/ECXXXXXX
      8ADevices for indirect vision and their installation

      Regulation (EC) No 661/2009

      UNECE Regulation No 46

      XXXXXX
      9BrakingDirective 71/320/EECXXXXXXXXXX
      9ABraking of vehicles and trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 13

      Xf3 X X X X X X X X
      9BBraking of passenger cars

      Regulation (EC) No 661/2009

      UNECE Regulation No 13-H

      Xf4 X
      10Radio interference (electromagnetic compatibility)Directive 72/245/EECXXXXXXXXXX
      10AElectromagnetic compatibility

      Regulation (EC) No 661/2009

      UNECE Regulation No 10

      XXXXXXXXXX
      12Interior fittingsDirective 74/60/EECX
      12AInterior fittings

      Regulation (EC) No 661/2009

      UNECE Regulation No 21

      X
      13Anti-theft and immobiliserDirective 74/61/EECXXXXXX
      13AProtection of motor vehicles against unauthorised use

      Regulation (EC) No 661/2009

      UNECE Regulation No 18

      Xf5 X X X
      13BProtection of motor vehicles against unauthorised use

      Regulation (EC) No 661/2009

      UNECE Regulation No 116

      XX
      14Protective steeringDirective 74/297/EECXX
      14AProtection of the driver against the steering mechanism in the event of impact

      Regulation (EC) No 661/2009

      UNECE Regulation No 12

      XX
      15Seat strengthDirective 74/408/EECXXXXXX
      15ASeats, their anchorages and any head restraints

      Regulation (EC) No 661/2009

      UNECE Regulation No 17

      XXf6 X XXX
      15BSeats of large passenger vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 80

      XX
      16Exterior projectionsDirective 74/483/EECX
      16AExternal projections

      Regulation (EC) No 661/2009

      UNECE Regulation No 26

      X
      17Speedometer and reverse gearDirective 75/443/EECXXXXXX
      17AVehicle access and manoeuvrability

      Regulation (EC) No 661/2009

      Regulation (EU) No 130/2012

      XXXXXX
      17BSpeedometer equipment including its installation

      Regulation (EC) No 661/2009

      UNECE Regulation No 39

      XXXXXX
      18Statutory platesDirective 76/114/EECXXXXXXXXXX
      18AManufacturer’s statutory plate and vehicle identification number

      Regulation (EC) No 661/2009

      Regulation (EU) No 19/2011

      XXXXXXXXXX
      19Seat belt anchoragesDirective 76/115/EECXXXXXX
      19ASafety-belt anchorages, Isofix anchorages systems and Isofix top tether anchorages

      Regulation (EC) No 661/2009

      UNECE Regulation No 14

      XXXXXX
      20Installation of lighting and light signalling devicesDirective 76/756/EECXXXXXXXXXX
      20AInstallation of lighting and light-signalling devices on vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 48

      XXXXXXXXXX
      21Retro reflectorsDirective 76/757/EECXXXXXXXXXX
      21ARetro-reflecting devices for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 3

      XXXXXXXXXX
      22End-outline, front-position (side), rear-position (side), stop, side marker, daytime running lampsDirective 76/758/EECXXXXXXXXXX
      22AFront and rear position lamps, stop-lamps and end-outline marker lamps for motor vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 7

      XXXXXXXXXX
      22BDaytime running lamps for power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 87

      XXXXXX
      22CSide-marker lamps for motor vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 91

      XXXXXXXXXX
      23Direction indicatorsDirective 76/759/EECXXXXXXXXXX
      23ADirection indicators for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 6

      XXXXXXXXXX
      24Rear registration plate lampsDirective 76/760/EECXXXXXXXXXX
      24AIllumination of rear-registration plates of power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 4

      XXXXXXXXXX
      25Headlamps (including bulbs)Directive 76/761/EECXXXXXX
      25APower-driven vehicle’s sealed-beam headlamps (SB) emitting an European asymmetrical passing beam or a driving beam or both

      Regulation (EC) No 661/2009

      UNECE Regulation No 31

      XXXXXX
      25BFilament lamps for use in approved lamp units of power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 37

      XXXXXXXXXX
      25CMotor vehicle headlamps equipped with gas-discharge light sources

      Regulation (EC) No 661/2009

      UNECE Regulation No 98

      XXXXXX
      25DGas-discharge light sources for use in approved gas-discharge lamp units of power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 99

      XXXXXX
      25EMotor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with filament lamps and/or LED modules

      Regulation (EC) No 661/2009

      UNECE Regulation No 112

      XXXXXX
      25FAdaptive front-lighting systems (AFS) for motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 123

      XXXXXX
      26Front fog lampsDirective 76/762/EECXXXXXX
      26APower-driven vehicle front fog lamps

      Regulation (EC) No 661/2009

      UNECE Regulation No 19

      XXXXXX
      27Towing hooksDirective 77/389/EECXXXXXX
      27ATowing device

      Regulation (EC) No 661/2009

      Regulation (EU) No 1005/2010

      XXXXXX
      28Rear fog lampsDirective 77/538/EECXXXXXXXXXX
      28ARear fog lamps for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 38

      XXXXXXXXXX
      29Reversing lampsDirective 77/539/EECXXXXXXXXXX
      29AReversing lights for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 23

      XXXXXXXXXX
      30Parking lampsDirective 77/540/EECXXXXXX
      30AParking lamps for power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 77

      XXXXXX
      31Seat belts and restraint systemsDirective 77/541/EECXXXXXX
      31ASafety-belts, restraint systems, child restraint systems and Isofix child restraint systems

      Regulation (EC) No 661/2009

      UNECE Regulation No 16

      XXXXXX
      32Forward visionDirective 77/649/EECX
      32AForward field of vision

      Regulation (EC) No 661/2009

      UNECE Regulation No 125

      X
      33Identification of controls, tell-tales and indicatorsDirective 78/316/EECXXXXXX
      33ALocation and identification of hand controls, tell-tales and indicators

      Regulation (EC) No 661/2009

      UNECE Regulation No 121

      XXXXXX
      34Defrost/demistDirective 78/317/EECX f7
      34AWindscreen defrosting and demisting systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 672/2010

      X
      35Wash/wipeDirective 78/318/EECX f8
      35AWindscreen wiper and washer systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 1008/2010

      X
      36Heating systemsDirective 2001/56/ECXXXXXXXXXX
      36AHeating systems

      Regulation (EC) No 661/2009

      UNECE Regulation No 122

      XXXXXXXXXX
      37Wheel guardsDirective 78/549/EECX
      37AWheel guards

      Regulation (EC) No 661/2009

      Regulation (EU) No 1009/2010

      X
      38Head restraintsDirective 78/932/EECX
      38AHead restraints (headrests), whether or not incorporated in vehicle seats

      Regulation (EC) No 661/2009

      UNECE Regulation No 25

      XXXXXX
      40Engine powerDirective 80/1269/EECXf9 X X X X X
      41Emissions (Euro IV and V) heavy duty vehicles.Directive 2005/55/ECXf10 X XX X X
      41AEmissions (Euro VI) heavy duty vehicles/access to informationRegulation (EC) No 595/2009Xf11 X XX X X
      42Lateral protectionDirective 89/297/EECXXXX
      42ALateral protection of goods vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 73

      XXXX
      43Spray-suppression systemsDirective 91/226/EECXXXXXXX
      43ASpray suppression systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 109/2011

      XXXXXXX
      44Masses and dimensions (cars)Directive 92/21/EECX
      44AMasses and dimensions

      Regulation (EC) No 661/2009

      Regulation (EU) No 1230/2012

      X
      45Safety glazingDirective 92/22/EECXXXXXXXXXX
      45ASafety glazing materials and their installation on vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 43

      XXXXXXXXXX
      46TyresDirective 92/23/EECXXXXXXXXXX
      46AInstallation of tyres

      Regulation (EC) No 661/2009

      Regulation (EU) No 458/2011

      XXXXXXXXXX
      46BPneumatic tyres for motor vehicles and their trailers (Class C1)

      Regulation (EC) No 661/2009

      UNECE Regulation No 30

      XXXX
      46CPneumatic tyres for commercial vehicles and their trailers (Classes C2 and C3)

      Regulation (EC) No 661/2009

      UNECE Regulation No 54

      XXXXXXX
      46DTyre rolling sound emissions, adhesion on wet surfaces and rolling resistance (Classes C1, C2 and C3)

      Regulation (EC) No 661/2009

      UNECE Regulation No 117

      XXXXXXXXXX
      46ETemporary-use spare unit, run-flat tyres/system and tyre pressure monitoring system

      Regulation (EC) No 661/2009

      UNECE Regulation No 64

      Xf12 X
      47Speed limitation devicesDirective 92/24/EECXXXX
      47ASpeed limitation of vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 89

      XXXX
      48Masses and dimensions (other than vehicles referred to in item 44)Directive 97/27/ECXXXXXXXXX
      48AMasses and dimensions

      Regulation (EC) No 661/2009

      Regulation (EU) No 1230/2012

      XXXXXXXXX
      49External projections of cabsDirective 92/114/EECXXX
      49ACommercial vehicles with regard to their external projections forward of the cab’s rear panel

      Regulation (EC) No 661/2009

      UNECE Regulation No 61

      XXX
      50CouplingsDirective 94/20/ECXf13 X X X X X XXXX
      50AMechanical coupling components of combinations of vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 55

      X X X X X X XXXX
      50BClose-coupling device (CCD); fitting of an approved type of CCD

      Regulation (EC) No 661/2009

      UNECE Regulation No 102

      X X X X
      51FlammabilityDirective 95/28/ECX
      51ABurning behaviour of materials used in the interior construction of certain categories of motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 118

      X
      52Buses and coachesDirective 2001/85/ECXX
      52AM2 and M3 vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 107

      XX
      52BStrength of the superstructure of large passenger vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 66

      XX
      53Frontal impactDirective 96/79/ECXf14
      53AProtection of occupants in the event of a frontal collision

      Regulation (EC) No 661/2009

      UNECE Regulation No 94

      X
      54Side impactDirective 96/27/ECXf15 X
      54AProtection of occupants in the event of lateral collision

      Regulation (EC) No 661/2009

      UNECE Regulation No 95

      X X
      55(empty)
      56Vehicles intended for the transport of dangerous goodsDirective 98/91/ECXf16 X X X X X X
      56AVehicles for the carriage of dangerous goods

      Regulation (EC) No 661/2009

      UNECE Regulation No 105

      X X X X X X X
      57Front underrun protectionDirective 2000/40/ECXX
      57AFront underrun protective devices (FUPDs) and their installation; front underrun protection (FUP)

      Regulation (EC) No 661/2009

      UNECE Regulation No 93

      XX
      58Pedestrian protectionRegulation (EC) No 78/2009XX
      59RecyclabilityDirective 2005/64/ECXX-
      60(empty)
      61Air-conditioning systemsDirective 2006/40/ECXXf17
      62Hydrogen systemRegulation (EC) No 79/2009XXXXXX
      63General SafetyRegulation (EC) No 661/2009Xf18 X X X X X X X X X
      64Gear shift indicators

      Regulation (EC) No 661/2009

      Regulation (EU) No 65/2012

      X
      65Advanced emergency braking system

      Regulation (EC) No 661/2009

      Regulation (EU) No 347/2012

      XXXX
      66Lane departure warning system

      Regulation (EC) No 661/2009

      Regulation (EU) No 351/2012

      XXXX
      67Specific components for liquefied petroleum gases (LPG) and their installation on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 67

      XXXXXX
      68Vehicle alarm systems (VAS)

      Regulation (EC) No 661/2009

      UNECE Regulation No 97

      XX
      69Electric safety

      Regulation (EC) No 661/2009

      UNECE Regulation No 100

      XXXXXX
      70Specific components for CNG and their installation on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 110

      XXXXXX

      ’;

    2. (b)

      Appendix 1 to Part I is replaced by the following:

      Appendix 1

      Regulatory acts for EC type-approval of vehicles produced in small series pursuant to Article 22

      1.

      This Appendix applies to new EC type-approvals of small series granted from 1 November 2012, except for item 54A which applies from 1 November 2014.

      2.

      EC type-approvals of small series granted before 1 November 2012 shall cease to be valid on 31 October 2016. National authorities shall consider certificates of conformity for vehicles to be no longer valid for the purposes of Article 26(1) of this Directive, unless the type-approvals concerned have been updated to the requirements of this Appendix.

      Table 1
      M1 vehicles f19

      The explanatory notes relating to Part I of Annex IV apply also to Table 1.

      Meaning of letters

      Note: The series of amendments of the UNECE Regulations to be used are listed in Annex IV to Regulation (EC) No 661/2009. Series of amendments adopted subsequently are accepted as an alternative.
      X

      Full application of the regulatory act.

      1. (a)

        a type-approval certificate shall be issued;

      2. (b)

        tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 41, 42 and 43;

      3. (c)

        a test report shall be drafted in accordance with the provisions of Annex V;

      4. (d)

        Conformity of Production (COP) shall be ensured.

      A

      Application of the regulatory act as follows:

      1. (a)

        all requirements of the regulatory act shall be fulfilled unless otherwise stated;

      2. (b)

        no type-approval certificate shall be required;

      3. (c)

        tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 41, 42 and 43;

      4. (d)

        a test report shall be drafted in accordance with the provisions of Annex V;

      5. (e)

        COP shall be ensured.

      B

      Application of the regulatory act as follows:

      As for letter “A” with the exception that the tests and checks may be performed by the manufacturer himself subject to the agreement of the type-approval authority (i.e. the conditions laid down in Articles 41, 42 and 43 do not have to be fulfilled).

      C

      Application of the regulatory act as follows:

      1. (a)

        only the technical requirements from the regulatory shall be fulfilled, irrespective of any transitional provision;

      2. (b)

        no type-approval certificate shall be required;

      3. (c)

        tests and checks shall be conducted by the technical service or by the manufacturer (see decisions for letter “B”);

      4. (d)

        a test report shall be drafted in accordance with the provisions of Annex V;

      5. (e)

        COP shall be ensured.

      D

      Same as for decisions in letters “B” and “C” with the exception that a statement of compliance submitted by the manufacturer is sufficient. No test report shall be required.

      The type-approval authority or technical service may require additional information of further evidence, if need be.

      N/AThe regulatory act shall not apply. Compliance with one or more specific aspects included in the regulatory act may however be imposed.
      ItemSubjectRegulatory actSpecific issuesApplicability and specific requirements
      1Permissible sound levelDirective 70/157/EECA
      2Emissions (Euro 5 and 6) light duty vehicles/access to informationRegulation (EC) No 715/2007A

      (a)

      On-board diagnostic (OBD)

      The vehicle shall be fitted with an OBD system that fulfils the requirements of Article 4(1) and (2) of Regulation (EC) No 692/2008 (The OBD system shall be designed to record at least the malfunction of the engine management system).

      The OBD-interface shall be able to communicate with commonly available diagnostic tools.

      (b)

      In service conformity

      N/A

      (c)

      Access to information

      It is sufficient that the manufacturer provide access to repair and maintenance information in a readily accessible and prompt manner.
      3APrevention of fire risks (liquid fuel tanks)

      Regulation (EC) No 661/2009

      UNECE Regulation No 34

      (a)

      Liquid fuel tanks

      B

      (b)

      Installation in vehicle

      B
      4ASpace for mounting and fixing rear registration plates

      Regulation (EC) No 661/2009

      Regulation (EU) No 1003/2010

      B
      5ASteering equipment

      Regulation (EC) No 661/2009

      UNECE Regulation No 79

      C

      (a)

      Mechanical systems

      The provisions of paragraph 5 of UNECE Regulation No 79 shall apply.

      All tests prescribed in paragraph 6.2 of UNECE Regulation No 79 shall be performed and the requirements of paragraph 6.1 of UNECE Regulation No 79 shall apply.

      (b)

      Complex electronic vehicle control system

      All the requirements of Annex 6 of UNECE Regulation No 79 shall apply.

      Compliance with these requirements may only be checked by an appointed technical service.

      6ADoor latches and door retention components

      Regulation (EC) No 661/2009

      UNECE Regulation No 11

      C

      (a)

      General requirements (Paragraph 5 of UNECE Regulation No 11)

      All the requirements shall apply.

      (b)

      Performance requirements (Paragraph 6 of UNECE Regulation No 11)

      Only the requirements of paragraph 6.1.5.4 and paragraph 6.3 on door locks shall apply.
      7AAudible warning devices and signals

      Regulation (EC) No 661/2009

      UNECE Regulation No 28

      (a)

      Components

      X

      (b)

      Installation on vehicle

      B
      8ADevices for indirect vision and their installation

      Regulation (EC) No 661/2009

      UNECE Regulation No 46

      (a)

      Components

      X

      (b)

      Installation on vehicle

      B
      9BBraking

      Regulation (EC) No 661/2009

      UNECE Regulation No 13-H

      (a)

      Design and tests requirements

      A

      (b)

      Electronic stability control (ESC) and brake assist systems(BAS)

      The fitting of BAS and ESC shall not be required. If fitted, they shall comply with the requirements of UNECE Regulation No 13-H.
      10AElectromagnetic compatibility

      Regulation (EC) No 661/2009

      UNECE Regulation No 10

      B
      12AInterior fittings

      Regulation (EC) No 661/2009

      UNECE Regulation No 21

      C

      (a)

      Interior arrangement

      (i)

      Radii and protrusion requirements for switches, pull-knobs and the like, controls and general interior fittings

      The requirements of paragraphs 5.1 to 5.6 of UNECE Regulation No 21 may be waived at the request of the manufacturer.

      The requirements of paragraph 5.2 of UNECE Regulation No 21 with the exception of paragraphs 5.2.3.1, 5.2.3.2 and 5.2.4 shall apply.

      (ii)

      Energy absorption tests on the upper dashboard

      Energy absorption tests on the upper dashboard shall only be performed when the vehicle is not fitted with at least two front airbags or two static four-point harnesses.

      (iii)

      Energy absorption test on the rear part of the seats

      N/A

      (b)

      Power-operation of windows, roof-panel systems and partition systems

      All requirements of paragraph 5.8 UNECE Regulation No 21 shall apply.
      13AProtection of motor vehicles against unauthorised use

      Regulation (EC) No 661/2009

      UNECE Regulation No 116

      A
      14AProtection of the driver against the steering mechanism in the event of impact

      Regulation (EC) No 661/2009

      UNECE Regulation No 12

      C
      Tests are required when the vehicle has not been tested under UNECE Regulation No 94 (see item 53A)
      15ASeats, their anchorages and any head restraints

      Regulation (EC) No 661/2009

      UNECE Regulation No 17

      C

      (a)

      General requirements

      1. (i)

        Specifications

      Requirements of paragraph 5.2 of UNECE Regulation No 17 shall apply with the exception of paragraph 5.2.3.

      (ii)

      Strength tests for seat backrest and head restraints

      The requirements of paragraph 6.2 UNECE Regulation No 17 shall apply.

      (iii)

      Unlocking and adjustment tests

      The test shall be performed in accordance with the requirements of Annex 7 to UNECE Regulation No 17.

      (b)

      Head restraints

      1. (i)

        Specifications

      Requirements of paragraphs 5.4, 5.5, 5.6, 5.10, 5.11 and 5.12 of UNECE Regulation No 17 shall apply with the exception of paragraph 5.5.2.

      (ii)

      Strength tests on head restraints

      The test prescribed in paragraph 6.4 shall be performed.

      (c)

      Special requirements regarding the protection of occupants from displaced luggage

      The requirements of Annex 9 to UNECE Regulation No 26 may be waived at the request of the manufacturer.
      16AExternal projections

      Regulation (EC) No 661/2009

      UNECE Regulation No 26

      C

      (a)

      General specifications

      The requirements of paragraph 5 of UNECE Regulation No 26 shall apply.

      (b)

      Particular specifications

      The requirements of paragraph 6 of UNECE Regulation No 26 shall apply.
      17AVehicle access and manoeuvrability

      Regulation (EC) No 661/2009

      Regulation (EU) No 130/2012

      D
      17BSpeedometer equipment including its installation

      Regulation (EC) No 661/2009

      UNECE Regulation No 39

      B
      18AManufacturer’s statutory plate and vehicle identification number

      Regulation (EC) No 661/2009

      Regulation (EU) No 19/2011

      B
      19ASafety-belt anchorages, Isofix anchorages systems and Isofix top tether anchorages

      Regulation (EC) No 661/2009

      UNECE Regulation No 14

      B
      20AInstallation of lighting and light-signalling devices on vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 48

      B

      Daytime Running Lights (DRL) shall be fitted to a new vehicle type in accordance with Article 2 of Directive 2008/89/EC.

      21ARetro-reflecting devices for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 3

      X
      22AFront and rear position lamps, stop-lamps and end-outline marker lamps for motor vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 7

      X
      22BDaytime running lamps for power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 87

      X
      22CSide-marker lamps for motor vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 91

      X
      23ADirection indicators for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 6

      X
      24AIllumination of rear-registration plates of power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 4

      X
      25APower-driven vehicle’s sealed-beam headlamps (SB) emitting an European asymmetrical passing beam or a driving beam or both

      Regulation (EC) No 661/2009

      UNECE Regulation No 31

      X
      25BFilament lamps for use in approved lamp units of power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 37

      X
      25CMotor vehicle headlamps equipped with gas-discharge light sources

      Regulation (EC) No 661/2009

      UNECE Regulation No 98

      X
      25DGas-discharge light sources for use in approved gas-discharge lamp units of power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 99

      X
      25EMotor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with filament lamps and/or LED modules

      Regulation (EC) No 661/2009

      UNECE Regulation No 112

      X
      25FAdaptive front-lighting systems (AFS) for motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 123

      X
      26APower-driven vehicle front fog lamps

      Regulation (EC) No 661/2009

      UNECE Regulation No 19

      X
      27ATowing device

      Regulation (EC) No 661/2009

      Regulation (EU) No 1005/2010

      B
      28ARear fog lamps for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 38

      X
      29AReversing lights for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 23

      X
      30AParking lamps for power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 77

      X
      31ASafety-belts, restraint systems, child restraint systems and Isofix child restraint systems

      Regulation (EC) No 661/2009

      UNECE Regulation No 16

      (a)

      Components

      X

      (b)

      Installation requirements

      B
      32AForward field of vision

      Regulation (EC) No 661/2009

      UNECE Regulation No 125

      A
      33ALocation and identification of hand controls, tell-tales and indicators

      Regulation (EC) No 661/2009

      UNECE Regulation No 121

      A
      34AWindscreen defrosting and demisting systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 672/2010

      C

      (a)

      Windscreen defrosting

      Only paragraph 1.1.1 of Annex II to Regulation (EU) No 672/2010 shall apply provided that warm air flow is ducted to the whole surface of the windscreen or the latter is electrically heated on its whole surface.

      (b)

      Windscreen demisting

      Only point 1.2.1 of Annex II to Regulation (EU) No 672/2010 shall apply provided that warm air flow is ducted to the whole surface of the windscreen or the latter is electrically heated on its whole surface.
      35AWindscreen wiper and washer systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 1008/2010

      C

      (a)

      Windscreen wiper system

      Paragraphs 1.1 to 1.1.10 of Annex III to Regulation (EU) No 1008/2010 shall apply.

      Only the test described in paragraph 2.1.10 of Annex III to Regulation (EU) No 1008/2010 shall be performed.

      (b)

      Windscreen washer system

      Section 1.2 of Annex III to Regulation (EU) No 1008/2010 shall apply with the exception of points 1.2.2, 1.2.3 and 1.2.5.
      36AHeating system

      Regulation (EC) No 661/2009

      UNECE Regulation No 122

      C

      The fitting of a heating system shall not be required.

      (a)

      All heating systems

      The requirements of paragraph 5.3 and of paragraph 6 of UNECE Regulation No 122 shall apply.

      (b)

      LPG heating systems

      The requirements of Annex 8 to UNECE Regulation No 122 shall apply.
      37AWheel guards

      Regulation (EC) No 661/2009

      Regulation (EU) No 1009/2010

      B
      40Engine powerDirective 80/1269/EEC

      A

      (When the vehicle manufacturer produces his own engine).

      (When the vehicle manufacturer uses an engine from another manufacturer)

      Bench test data from the engine manufacturer are accepted provided that the engine management system is identical (i.e. having at least the same ECU).

      Power output test may be performed on a chassis dynamometer. It shall be taken into account of the power loss in the transmission.

      41Emissions (Euro IV and V) heavy duty vehiclesDirective 2005/55/ECA
      OBDMay be waived at the request of the vehicle manufacturer.
      41AEmissions (Euro VI) heavy duty vehicles/access to informationRegulation (EC) No 595/2009

      A

      With the exception of the set of requirements relating to OBDs and access to information.

      44AMasses and dimensions

      Regulation (EC) No 661/2009

      Regulation (EU) No 1230/2012

      B

      The hill start test at maximum combination mass described in paragraph 5.1 of Part A of Annex 1 to Regulation (EU) No 1230/2012 may be waived at the request of the manufacturer.

      45ASafety glazing materials and their installation on vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 43

      (a)

      Components

      X

      (b)

      Installation

      B
      46TyresDirective 92/23/EECComponentsX
      46AInstallation of tyres

      Regulation (EC) No 661/2009

      Regulation (EU) No 458/2011

      B

      Dates for progressive application shall be those set out in Article 13 of Regulation (EC) No 661/2009.

      46BPneumatic tyres for motor vehicles and their trailers (Class C1)

      Regulation (EC) No 661/2009

      UNECE Regulation No 30

      ComponentsX
      46DTyre rolling sound emissions, adhesion on wet surfaces and rolling resistance (classes C1, C2 and C3)

      Regulation (EC) No 661/2009

      UNECE Regulation No 117

      ComponentsX
      46ETemporary-use spare unit, run-flat tyres/system and tyre pressure monitoring system

      Regulation (EC) No 661/2009

      UNECE Regulation No 64

      ComponentsX
      Fitting of a tyre-pressure monitoring system (TPMS)

      B

      The fitting of a TPMS shall not be required.

      50AMechanical coupling components of combinations of vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 55

      (a)

      Components

      X

      (b)

      Installation

      B
      53AProtection of occupants in the event of a frontal collision

      Regulation (EC) No 661/2009

      UNECE Regulation No 94

      C

      The requirements of UNECE Regulation No 94 shall apply to vehicles fitted with front airbags. Vehicles not fitted with airbags shall fulfil the requirement of item 14A of this table.

      54AProtection of occupants in the event of lateral collision

      Regulation (EC) No 661/2009

      UNECE Regulation No 95

      C

      (shall apply from 1 November 2014)

      Head form test

      The manufacturer shall supply the technical service with suitable information concerning a possible impact of the head of the dummy against the structure of the vehicle or the side glazing if made up of laminated glazing.

      When such impact is proven likely to happen, then the partial test using the head form test described in paragraph 3.1 of Annex 8 to UNECE Regulation No 95 shall be conducted and the criterion specified in paragraph 5.2.1.1 of UNECE Regulation 95 shall be met.

      In agreement with the technical service, the test procedure described in Annex 4 to UNECE Regulation No 21 may be used as an alternative to the test mentioned above.

      58Pedestrian protectionRegulation (EC) No 78/2009

      (a)

      Technical requirements applicable to vehicle

      N/A

      (b)

      Frontal protection systems

      X
      59RecyclabilityDirective 2005/64/EC

      N/A

      Only Article 7 on reuse of component parts shall apply.

      61Air-conditioning systemsDirective 2006/40/EC

      A

      Fluorinated greenhouse gases with a global warming potential higher than 150 are permitted until 31 December 2016.

      62Hydrogen systemRegulation (EC) No 79/2009X
      63General SafetyRegulation (EC) No 661/2009Under this item, a type-approval may be granted, at the request of the manufacturer. See footnote (15) of the table for vehicles produced in unlimited series
      64Gear shift indicators

      Regulation (EC) No 661/2009

      Regulation (EU) No 65/2012

      N/A
      67Specific components for liquefied petroleum gases (LPG) and their installation on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 67

      (a)

      Components

      X

      (b)

      Installation

      A
      68Vehicle alarm systems (VAS)

      Regulation (EC) No 661/2009

      UNECE Regulation No 97

      (a)

      Components

      X

      (b)

      Installation

      B
      69Electric safety

      Regulation (EC) No 661/2009

      UNECE Regulation No 100

      B
      70Specific components for CNG and their installation on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 110

      (a)

      Components

      X

      (b)

      Installation

      A
      Table 2
      N1 vehicles f20

      The explanatory notes relating to Part I of Annex IV apply also to Table 2. The letters in Table 2 have the same meaning as in Table 1.

      ItemSubjectRegulatory actSpecific issuesApplicability and specific requirements
      1Permissible sound levelDirective 70/157/EECA
      2Emissions (Euro 5 and 6) light duty vehicles/access to informationRegulation (EC) No 715/2007A

      (a)

      OBD

      The vehicle shall be fitted with an OBD system that fulfils the requirements of Article 4(1) and (2) of Regulation (EC) No 692/2008(the OBD system shall be designed to record at least the malfunction of the engine management system).

      The OBD-interface shall be able to communicate with commonly available diagnostic tools.

      (b)

      In service conformity

      N/A

      (c)

      Access to information

      It is sufficient that the manufacturer provides access to repair and maintenance information in a readily accessible and prompt manner.
      3APrevention of fire risks (liquid fuel tanks)

      Regulation (EC) No 661/2009

      UNECE Regulation No 34

      (a)

      Liquid fuel tanks

      B

      (b)

      Installation in vehicle

      B
      4ASpace for mounting and fixing rear registration plates

      Regulation (EC) No 661/2009

      Regulation (EU) No 1003/2010

      B
      5ASteering equipment

      Regulation (EC) No 661/2009

      UNECE Regulation No 79

      C

      (a)

      Mechanical systems

      The provisions of paragraph 5 of UNECE Regulation No 79.01 shall apply.

      All tests prescribed in paragraph 6.2 of UNECE Regulation No 79 shall be performed and the requirements of paragraph 6.1 of UNECE Regulation No 79 shall apply.

      (b)

      Complex electronic vehicle control system

      All the requirements of Annex 6 of UNECE Regulation No 79 shall apply.

      Compliance with these requirements may only be checked by an appointed technical service.

      6ADoor latches and door retention components

      Regulation (EC) No 661/2009

      UNECE Regulation No 11

      C

      (a)

      General requirements (Paragraph 5 of UNECE Regulation No 11)

      All requirements shall apply.

      (b)

      Performance requirements (Paragraph 6 of UNECE Regulation No 11)

      Only the requirements of paragraph 6.1.5.4 and paragraph 6.3 on door locks shall apply.
      7AAudible warning devices and signals

      Regulation (EC) No 661/2009

      UNECE Regulation No 28

      (a)

      Components

      X

      (b)

      Installation on vehicle

      B
      8ADevices for indirect vision and their installation

      Regulation (EC) No 661/2009

      UNECE Regulation No 46

      (a)

      Components

      X

      (b)

      Installation on vehicle

      B
      9ABraking of vehicles and trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 13.

      (a)

      design and test requirements

      A

      (b)

      ESC

      The fitting of ESC shall not be required. If fitted, it shall comply with the requirements of UNECE Regulation No 13.
      9BBraking of passenger cars

      Regulation (EC) No 661/2009

      UNECE Regulation No 13-H

      (a)

      Design and test requirements

      A

      (b)

      Electronic stability control (ESC) and brake assist systems(BAS)

      The fitting of BAS and ESC shall not be required. If fitted, they shall comply with the requirements of UNECE Regulation No 13-H.
      10AElectromagnetic compatibility

      Regulation (EC) No 661/2009

      UNECE Regulation No 10

      B
      13AProtection of motor vehicles against unauthorised use

      Regulation (EC) No 661/2009

      UNECE Regulation No 116

      A
      14AProtection of the driver against the steering mechanism in the event of impact

      Regulation (EC) No 661/2009

      UNECE Regulation No 12

      C

      (a)

      Barrier impact test

      A test shall be required.

      (b)

      Body block impact test against steering wheel

      Not required if the steering wheel is fitted with an airbag.

      (c)

      Head form test

      Not required if the steering wheel is fitted with an airbag.
      15ASeats, their anchorages and any head restraints

      Regulation (EC) No 661/2009

      UNECE Regulation N 17

      B
      17AVehicle access and manoeuvrability

      Regulation (EC) No 661/2009

      Regulation (EU) No 130/2012

      D
      17BSpeedometer equipment including its installation

      Regulation (EC) No 661/2009

      UNECE Regulation No 39

      B
      18AManufacturer’s statutory plate and vehicle identification number

      Regulation (EC) No 661/2009

      Regulation (EU) No 19/2011

      B
      19ASafety-belt anchorages, Isofix anchorages systems and Isofix top tether anchorages

      Regulation (EC) No 661/2009

      UNECE Regulation No 14

      B
      20AInstallation of lighting and light-signalling devices on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 48

      B

      DRLs shall be fitted to a new vehicle type in accordance with Article 2 of Directive 2008/89/EC.

      21ARetro-reflecting devices for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 3

      X
      22AFront and rear position lamps, stop-lamps and end-outline marker lamps for motor vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 7

      X
      22BDaytime running lamps for power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 87

      X
      22CSide-marker lamps for motor vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 91

      X
      23ADirection indicators for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 6

      X
      24AIllumination of rear-registration plates of power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 4

      X
      25APower-driven vehicle’s sealed-beam headlamps (SB) emitting an European asymmetrical passing beam or a driving beam or both

      Regulation (EC) No 661/2009

      UNECE Regulation No 31

      X
      25BFilament lamps for use in approved lamp units of power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 37

      X
      25CMotor vehicle headlamps equipped with gas-discharge light sources

      Regulation (EC) No 661/2009

      UNECE Regulation No 98

      X
      25DGas-discharge light sources for use in approved gas-discharge lamp units of power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 99

      X
      25EMotor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with filament lamps and/or LED modules

      Regulation (EC) No 661/2009

      UNECE Regulation No 112

      X
      25FAdaptive front-lighting systems (AFS) for motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 123

      X
      26APower-driven vehicle front fog lamps

      Regulation (EC) No 661/2009

      UNECE Regulation No 19

      X
      27ATowing device

      Regulation (EC) No 661/2009

      Regulation (EU) No 1005/2010

      B
      28ARear fog lamps for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 38

      X
      29AReversing lights for power-driven vehicles and their trailers

      Regulation (EC) No 661/2009

      UNECE Regulation No 23

      X
      30AParking lamps for power-driven vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 77

      X
      31ASafety-belts, restraint systems, child restraint systems and Isofix child restraint systems

      Regulation (EC) No 661/2009

      UNECE Regulation No 16

      (a)

      Components

      X

      (b)

      Installation requirements

      B
      33ALocation and identification of hand controls, tell-tales and indicators

      Regulation (EC) No 661/2009

      UNECE Regulation No 121

      A
      34AWindscreen defrosting and demisting systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 672/2010

      N/A

      The vehicle shall be fitted with a suitable windscreen defrosting and demisting system.

      35AWindscreen wiper and washer systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 1008/2010

      N/A

      The vehicle shall be fitted with a suitable windscreen wiper and washer system.

      36AHeating system

      Regulation (EC) No 661/2009

      UNECE Regulation No 122

      C

      The fitting of a heating system shall not be required.

      (a)

      All heating systems

      The requirements of paragraph 5.3 and of paragraph 6 of UNECE Regulation No 122 shall apply.

      (b)

      LPG heating systems

      The requirements of Annex 8 to UNECE Regulation No 122 shall apply.
      38Head restraints whether or not incorporated in vehicle seats

      Regulation (EC) No 661/2009

      UNECE Regulation No 25

      X
      40Engine powerDirective 80/1269/EEC

      A

      (When the vehicle manufacturer produces his own engine)

      (When the vehicle manufacturer uses an engine from another manufacturer)

      Bench test data from the engine manufacturer are accepted provided that the engine management system is identical (i.e. having at least the same ECU).

      Power output test may be performed on a chassis dynamometer. It shall be taken into account of the power loss in the transmission.

      41Emissions (Euro IV and V) heavy duty vehiclesDirective 2005/55/ECA
      OBDMaybe waived at the request of the vehicle manufacturer.
      41AEmissions (Euro VI) heavy duty vehicles/access to informationRegulation (EC) No 595/2009

      A

      With the exception of the set of requirements relating to OBDs and access to information.

      43ASpray suppression systems

      Regulation (EC) No 661/2009

      Regulation (EU) No 109/2011

      B
      45ASafety glazing materials and their installation on vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 43

      (a)

      Components

      X

      (b)

      Installation

      B
      46TyresDirective 92/23/EECComponentsX
      46AInstallation of tyres

      Regulation (EC) No 661/2009

      Regulation (EU) No 458/2011

      B

      Dates for progressive application shall be those set out in Article 13 of Regulation (EC) No 661/2009.

      46BPneumatic tyres for motor vehicles and their trailers (Class C1)

      Regulation (EC) No 661/2009

      UNECE Regulation No 30

      ComponentsX
      46CPneumatic tyres for commercial vehicles and their trailers (Classes C2 and C3)

      Regulation (EC) No 661/2009

      UNECE Regulation No 54

      ComponentsX
      46DTyre rolling sound emissions, adhesion on wet surfaces and rolling resistance (Classes C1, C2 and C3)

      Regulation (EC) No 661/2009

      UNECE Regulation No 117

      ComponentsX
      46ETemporary-use spare unit, run-flat tyres/system and tyre pressure monitoring system

      Regulation (EC) No 661/2009

      UNECE Regulation No 64

      ComponentsX
      Fitting of a tyre-pressure monitoring system

      B

      The fitting of a TPMS shall not be required

      48Masses and dimensionsDirective 97/27/ECB
      48AMasses and dimensions

      Regulation (EC) No 661/2009

      Regulation (EU) No 1230/2012

      B
      Hill start test at maximum combination massThe hill start test at maximum combination mass described in paragraph 5.1 of Part A of Annex 1 to Regulation (EU) No 1230/2012 may be waived at the request of the manufacturer.
      49ACommercial vehicles with regards to their external projections forward of the cab’s rear panel

      Regulation (EC) No 661/2009

      UNECE Regulation No 61

      C

      (a)

      General specifications

      The requirements of paragraph 5 of UNECE Regulation No 61 shall apply

      (b)

      Particular specifications

      The requirements of paragraph 6 of UNECE Regulation No 61 shall apply.
      50AMechanical coupling components of combinations of vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 55

      (a)

      Components

      X

      (b)

      Installation

      B
      54AProtection of occupants in the event of lateral collision

      Regulation (EC) No 661/2009

      UNECE Regulation No 95

      CC
      Head form test

      The manufacturer shall supply the technical service with suitable information concerning a possible impact of the head of the dummy against the structure of the vehicle or the side glazing if made up of laminated glazing.

      When such impact is proven likely to happen, then the partial test using the head form test described in paragraph 3.1 of Annex 8 to UNECE Regulation No 95 shall be conducted and the criterion specified in paragraph 5.2.1.1 of UNECE Regulation 95 shall be met.

      In agreement with the technical service, the test procedure described in Annex 4 to UNECE Regulation No 21 may be used as an alternative to the test mentioned above.

      56Vehicles for the carriage of dangerous goods

      Regulation (EC) No 661/2009

      UNECE Regulation No 105

      A
      58Pedestrian protectionRegulation (EC) No 78/2009

      (a)

      Technical requirements applicable to a vehicle

      N/A

      (b)

      Frontal protection systems

      X
      59RecyclabilityDirective 2005/64/EC

      N/A

      Only Article 7 on reuse of component parts shall apply.

      61Air-conditioning systemsDirective 2006/40/EC

      B

      Fluorinated greenhouse gases with a global warming potential higher than 150 are permitted until 31 December 2016.

      62Hydrogen systemRegulation (EC) No 79/2009X
      63General SafetyRegulation (EC) No 661/2009Under this item, a type-approval may be granted, at the request of the manufacturer. See footnote (15) of the table for vehicles produced in unlimited series
      67Specific components for liquefied petroleum gases (LPG) and their installation on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 67

      (a)

      Components

      X

      (b)

      Installation

      A
      68Vehicle alarm systems (VAS)

      Regulation (EC) No 661/2009

      UNECE Regulation No 97

      (a)

      Components

      X

      (b)

      Installation

      B
      69Electric safety

      Regulation (EC) No 661/2009

      UNECE Regulation No 100

      B
      70Specific components for CNG and their installation on motor vehicles

      Regulation (EC) No 661/2009

      UNECE Regulation No 110

      (a)

      Components

      X

      (b)

      Installation

      A
  2. (2)

    Part A of Annex XII is amended as follows:

    1. (a)

      In Section 1, the fourth line in the table is replaced by the following:

      ‘

      N11 000

      ’

    2. (b)

      Section 2 is amended as follows:

      1. (i)

        The second line in the table is replaced by the following:

        ‘

        M1100

        ’

      2. (ii)

        The fourth line in the table is replaced by the following:

        ‘

        N1

        500 until 31 October 2016

        250 from 1 November 2016

        ’