OpenLegislation

Commission Implementing Regulation (EU) No 901/2014 of 18 July 2014 implementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to the administrative requirements for the approval and market surveillance of two- or three-wheel vehicles and quadricycles (Text with EEA relevance)

EU Regulation No 901/2014 · Adopted 18 July 2014 · Extends to United Kingdom

Original text. legislation.gov.uk does not revise this item, so later amendments are not shown here. Changes made to it are listed under each provision when known.

Commission Implementing Regulation (EU) No 901/2014

of 18 July 2014

implementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to the administrative requirements for the approval and market surveillance of two- or three-wheel vehicles and quadricycles

(Text with EEA relevance)

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Regulation (EU) No 168/2013 of the European Parliament and of the Council of 15 January 2013 on the approval and market surveillance of two- or three-wheel vehicles and quadricyclesf1, and in particular Articles 22(7), 27(4), 29(4), 30(2), 30(3), 30(6), 32(1), 38(2), 39(3), 40(4), 50(2), 51(3), 57(8) and Article 72 thereof,

Whereas:

(1)

In the interest of clarity, predictability, rationality and simplification and in order to reduce the burden on vehicle manufacturers, this Regulation should, being based on existing practice, further simplify and standardise the documents used for type-approval procedures.

(2)

New technologies have been introduced in vehicles (e.g. electric engines or the application of Euro emission levels) since the templates used for type-approval procedures were drawn up in Directive 2002/24/EC of the European Parliament and of the Councilf2. The templates should be adapted as a result.

(3)

To indicate which procedure has been chosen by the manufacturer when applying for type-approval, a new template for an ‘information folder sheet’ should be introduced.

(4)

To ensure that vehicles are constructed so as to remain safe throughout a reasonable period of time, templates should be created for manufacturer’s statements regarding the endurance of functional safety-critical systems, parts and equipment, and vehicle structure integrity, in accordance with Regulation (EU) No 168/2013.

(5)

In order to ensure reasonable access for independent operators to vehicle repair information, including information relating to on-board diagnostic systems and their interaction with other vehicle systems, manufacturers shall provide unrestricted access to that information and submit proof of their compliance with that requirement to the approval authorities. A template for a corresponding manufacturer’s certificate should be laid down.

(6)

Three models of a certificate of conformity should be made available, corresponding to the type-approval procedures for complete, completed and incomplete vehicles.

(7)

To facilitate the conversion of the performance level of subcategories (L3e/L4e)-A2 to (L3e/L4e)-A3 and vice versa, a template for a corresponding manufacturer's statement to be attached to the information folder should be provided for. In addition, some new information and entries in the certificate of conformity should be added and the characteristics of a specific statutory plate for the subcategories concerned should be determined.

(8)

In accordance with Article 82(2) of Regulation 168/2013 manufacturers may request EU type-approval or national type-approval for new vehicle types under that Regulation already before the application day. In order to facilitate the early application of that Regulation, it should be allowed to use the template of the certificate of conformity set out in Annex IV to Directive 2002/24/EC until 31 December 2015 under the conditions set out in Article 5(2).

(9)

In order to simplify controls while reducing the administrative burden on manufacturers, the anti-tampering control plate should no longer be required and the relevant information it contained should be included on the statutory plate.

(10)

In order to simplify the most common EU type-approval certificate, a new model should be developed exclusively for EU whole-vehicle type-approval of a complete vehicle type, while for the other combinations of vehicle types; a different model of the EU whole-vehicle type-approval certificate should be established.

(11)

Where the manufacturer chooses the single-step type-approval procedure, a list of applicable requirements or acts with which the type of vehicle complies should be appended to the EU whole-vehicle type-approval certificate.

A template for an EU type-approval certificate should be established with regard to harmonise the different templates previously provided for in the separate Union directives for systems and components or separate technical units.

(12)

The numbering system of the EU type-approval certificates provided for under Annex V to Directive 2002/24/EC should be modified to reflect the new legal structure of the acts containing the type approval requirements with which conformity is certified.

(13)

To harmonise the presentation of the most relevant information in test reports, a minimum set of requirements for the format of the test reports should be established.

(14)

To easily identify the results of the tests carried out on the type-approved vehicle, a test result sheet containing a required minimum set of information should be appended to the EU type-approval certificate.

(15)

The list of parts or equipment which may pose a serious risk to the correct functioning of systems that are essential for the safety of the vehicle or for its environmental performance should be established.

(16)

The template for a certificate authorising the placing on the market of parts or equipment which may pose a serious risk to the correct functioning of systems that are essential for the safety of the vehicle or for its environmental performance should be established, together with a certificate numbering system.

(17)

The measures provided for in this Regulation are in accordance with the opinion of the Committee referred to in Article 73(1) of Regulation (EU) No 168/2013,

HAS ADOPTED THIS REGULATION:

Annotations to the whole text

Footnotes

f1

OJ L 60, 2.3.2013, p. 52.

f2

Directive 2002/24/EC of the European Parliament and of the Council of 18 March 2002 relating to the type-approval of two or three-wheel motor vehicles and repealing Council Directive 92/61/EEC (OJ L 124, 9.5.2002, p. 1).

Contents

  1. 1Subject matter
  2. 2Templates for the information document and for the information folder
  3. 3Templates for the manufacturer’s statements on endurance testing and vehicle structure integrity
  4. 4Templates for the manufacturer’s certificates providing proof of compliance to the type-approval authority on access to vehicle on-board diagnostics (OBD) and to vehicle repair and maintenance information
  5. 5Templates for the certificates of conformity
  6. 6Models for the statutory plate and EU type-approval mark
  7. 7Templates for the EU type-approval certificate
  8. 8Numbering system of the EU type-approval certificate
  9. 9Template for the test results sheet
  10. 10Format of test reports
  11. 11List of parts or equipment which may pose a serious risk to the correct functioning of essential systems
  12. 12Template and numbering system for the certificate for the placing on the market and entry into service of parts or equipment which may pose a serious risk to the correct functioning of essential systems
  13. 12aTransitional provisions
  14. 13Entry into force and application
  15. Signature
  16. Attachment
  17. Attachment
  18. Templates for the information document and information folder
  19. LIST OF APPENDICES
  20. INFORMATION FOLDER
  21. General requirements
  22. 1.1When applying for EU type-approval for a vehicle, system, component or separate technical unit, the manufacturer shall provide, in accordance with Article 27 of Regulation (EU) No 168/2013, an information folder which shall contain the following:
  23. 1.2Division 1.2
  24. 1.3Division 1.3
  25. Template of the information folder sheet
  26. Informationon the type-approval procedure chosen in accordance with Article 25(1) of Regulation (EU) No 168/2013
  27. INFORMATION DOCUMENT
  28. General requirements
  29. 1.1Division 1.1
  30. 1.2Division 1.2
  31. Type-approval numbers
  32. 1.3.1The manufacturer shall supply the information required by the following table in respect of the applicable subjects for the vehicle in Annex II to Regulation (EU) No 168/2013. All relevant approvals and test reports (if available) for each subject shall be included. However, information in respect of systems, components or separate technical units need not be given here so long as such information is included in the correspondent approval certificate.
  33. 1.4Division 1.4
  34. 2Content of the information document
  35. 2.1Division 2.1
  36. 2.2Division 2.2
  37. 2.3Division 2.3
  38. 2.3.1Division 2.3.1
  39. 2.3.2Division 2.3.2
  40. 2.3.3Division 2.3.3
  41. Type-, variant- and version designations
  42. 2.4.1Division 2.4.1
  43. 2.4.2Division 2.4.2
  44. 2.4.3Division 2.4.3
  45. 2.4.4Division 2.4.4
  46. 2.4.5Division 2.4.5
  47. Number of characters for the TVV
  48. 2.4.6.1The number of characters shall not exceed:
  49. 2.4.6.2Division 2.4.6.2
  50. 2.4.6.3When the TVV is used as a whole, a space shall be left between the type, the variant and the version.
  51. 2.5Division 2.5
  52. 2.6Division 2.6
  53. 2.7Division 2.7
  54. 2.8INFORMATION DOCUMENT DATA ENTRIES
  55. Attachment

1Subject matter

This Regulation provides for the implementing measures referred to in Article 72 of Regulation (EU) No 168/2013 to establish uniform conditions for the implementation of the administrative requirements for the approval of new two- or three-wheel vehicles and quadricycles, as well as systems, components and separate technical units designed and constructed for such vehicles. It also establishes the administrative requirements for placing on the market and entry into service of parts or equipment which may pose a serious risk to the correct functioning of essential systems.

2Templates for the information document and for the information folder

Manufacturers applying for EU type-approval shall provide the information document and the information folder referred to in Article 27(1) and Article 27(2)(a) of Regulation (EU) No 168/2013 on the basis of the templates set out in Annex I to this Regulation.

3Templates for the manufacturer’s statements on endurance testing and vehicle structure integrity

Manufacturers applying for EU type-approval shall provide statements on endurance of functional safety-critical systems, parts and equipment referred to in Article 22(2) of Regulation (EU) No 168/2013 and on vehicle structure integrity as referred to in Annex XIX to Commission Delegated Regulation (EU) No 3/2014f1 to that Regulation on the basis of the templates set out in Annex II to this Regulation.

4Templates for the manufacturer’s certificates providing proof of compliance to the type-approval authority on access to vehicle on-board diagnostics (OBD) and to vehicle repair and maintenance information

Manufacturers applying for EU type-approval shall provide the approval authority with a certificate on access to vehicle OBD and vehicle repair and maintenance information in accordance with Article 57(8) of Regulation (EU) No 168/2013 on the basis of the templates set out in Annex III to this Regulation.

5Templates for the certificates of conformity

1.

Manufacturers shall issue the certificate of conformity referred to in Article 38(1) of Regulation (EU) No 168/2013 in accordance with the templates set out in Annex IV to this Regulation.

2.

In accordance with Article 82(2) of Regulation (EU) 168/2013 allowing manufacturers to request type-approvals already under that Regulation as from the entry into force of this Implementing Regulation until 31 December 2015, manufacturers may use for vehicles of such newly approved types, alternatively to the template for the Certificate of Conformity laid down in Appendix 1 of Annex IV, the template for the Certificate of Conformity set out in Annex IV to Directive 2002/24/EC which must include in its entries No 04 ‘Vehicle category’ and No 50 ‘Remarks:’ the information and entries laid down in Appendix 2 of Annex IV.

6Models for the statutory plate and EU type-approval mark

Manufacturers shall issue the statutory plate and the EU type-approval mark referred to in Article 39(1) and (2) of Regulation (EU) No 168/2013 in accordance with the models set out in Annex V to this Regulation.

7Templates for the EU type-approval certificate

Approval authorities shall issue the EU type-approval certificates referred to in Article 30(1) of Regulation (EU) No 168/2013 on the basis of the templates set out in Annex VI to this Regulation.

8Numbering system of the EU type-approval certificate

Pursuant to Article 29(4) of Regulation (EU) No 168/2013, the EU type-approval certificates shall be numbered in accordance with the harmonised system set out in Annex VII to this Regulation.

9Template for the test results sheet

Approval authorities shall issue the test results sheet referred to in Article 30(3) of Regulation (EU) No 168/2013 on the basis of the template set out in Annex VIII to this Regulation.

10Format of test reports

The format of the test reports referred to in Article 32(1) of Regulation (EU) No 168/2013 shall comply with the general requirements set out in Annex VIII to this Regulation.

11List of parts or equipment which may pose a serious risk to the correct functioning of essential systems

The list of parts or equipment which may pose a serious risk to the correct functioning of systems that are essential for the safety of the vehicle or for its environmental performance referred to in Article 50(2) of Regulation (EU) No 168/2013 is set out in Annex X to this Regulation.

12Template and numbering system for the certificate for the placing on the market and entry into service of parts or equipment which may pose a serious risk to the correct functioning of essential systems

Approval authorities shall issue the certificate for the placing on the market and entry into service of parts or equipment which may pose a serious risk to the correct functioning of systems that are essential for the safety of the vehicle or for its environmental performance referred to in Article 51(2) of Regulation (EU) No 168/2013 on the basis of the template and in accordance with the numbering system set out in Annex IX to this Regulation.

12aTransitional provisionsF1

1.

Until 30 June 2020 , national authorities shall continue to grant type-approvals to vehicle types in accordance with this Regulation in its version applicable on 11 March 2020 .

2.

Until 31 December 2020 , the Member States shall permit the placing on the market, registration and entry into service of vehicles based on a vehicle type approved in accordance with this Regulation in its version applicable on 11 March 2020 .

13Entry into force and application

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

It shall apply from 1 January 2016.

Signature

This Regulation shall be binding in its entirety and directly applicable in all Member States.

LIST OF ANNEXES

F1Annex Number Annex Title
I Templates for the information document and information folder
II Templates for the manufacturer’s statements on endurance testing and vehicle structure integrity
III Templates for the manufacturer’s certificates providing proof of compliance to the type-approval authority on access to vehicle on-board diagnostics (OBD) and to vehicle repair and maintenance information
IV Templates for the certificates of conformity
V Models for the statutory plate and EU type-approval mark
VI Templates for the EU type-approval certificate
VII Numbering system of the EU type-approval certificate
VIII Format of test reports and template for the test results sheet
IX Template and numbering system for the certificate for the placing on the market and entry into service of parts or equipment which may pose a serious risk to the correct functioning of essential systems
X List of parts or equipment which may pose a serious risk to the correct functioning of essential systems

ANNEX I

LIST OF APPENDICES

F1Appendix Number Appendix title
1 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a tailpipe pollution-control system
2 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a crankcase and evaporative emissions system
3 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an on-board diagnostic (OBD) system
4 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a sound level system
5 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a propulsion unit performance system
F25a Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a maximum torque and a maximum net power of a propulsion unit system
6 Model information document relating to EU type-approval of a pollution-control device as a STU
7 Model information document relating to EU type-approval of a noise-abatement device as a STU
8 Model information document relating to EU type-approval of an exhaust (pollution-control device and noise-abatement device) as a STU
8a Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of audible warning devices system
9 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a braking system
9a Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of glazing, windscreen wipers and defrosting and demisting devices system
9b Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an identification of controls, tell-tales and indicators system
10 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of lighting and light-signalling devices system
11 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a roll-over protective structure (ROPS) system
11a Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a safety belt anchorages system
11b Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a steer-ability, cornering properties and turn ability system
12 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of tyres system
13 Model information document relating to EU type-approval of an audible warning device as a component
13a Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a vehicle occupant protection, including interior fittings, head restraint and vehicle doors system
14 Model information document relating to EU type-approval of a non-glazing front windscreen as a component/STU
15 Model information document relating to EU type-approval of a windscreen washer device as a component/STU
16 Model information document relating to EU type-approval of a rearward visibility device as a component/STU
17 Model information document relating to EU type-approval of safety belts as a STU
18 Model information document relating to EU type-approval of a seating position (saddle/seat) as a component/STU)
19 Model information document relating to EU type-approval of a trailer coupling device as a STU
20 Model information document relating to EU type-approval of devices to prevent unauthorised use as a STU
20a Model information document relating to EU type-approval of a fuel tank as a STU
21 Model information document relating to EU type-approval of passenger handholds as a STU
22 Model information document relating to EU type-approval of footrests as a STU
23 Model information document relating to EU type-approval of a side-car as a STU
24 Manufacturer's declaration for vehicles capable of converting their performance level from subcategory (L3e/L4e)-A2 to (L3e/L4e)-A3 and vice versa
25 Manufacturer’s declaration on powertrain tampering prevention measures (anti-tampering)

1.1When applying for EU type-approval for a vehicle, system, component or separate technical unit, the manufacturer shall provide, in accordance with Article 27 of Regulation (EU) No 168/2013, an information folder which shall contain the following:

  1. 1.1.1.

    a list of contents;

  2. 1.1.2.

    the information on the type-approval procedure chosen in accordance with Article 25(1) of Regulation (EU) No 168/2013, the template for which is set out in point 2 (information folder sheet);

  3. 1.1.3.

    the information document as set out in Part B of this Annex;

  4. 1.1.4.

    all relevant data, drawings, photographs and other information as required in the information document;

  5. 1.1.5.

    the manufacturer’s statement on endurance of functional safety-critical systems, parts and equipment as referred to in Article 22(2) of Regulation (EU) No 168/2013 and set out in Annex II to this regulation;

  6. 1.1.6.

    the manufacturer’s statement on vehicle structure integrity as referred to in Article 22(5) of Regulation (EU) No 168/2013 and in point 1.1.of Annex XIX to Commission Delegated Regulation (EU) No 3/2014 of 24 October 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to vehicle functional safety requirements for the approval of two- or three-wheel vehicles and quadricyclesf1, as set out point 1.4. of Annex II to this regulation;

  7. 1.1.7.

    the manufacturer’s certificate providing proof of compliance to the type-approval authority on access to vehicle on-board diagnostic (OBD) systems and to vehicle repair and maintenance information as referred to in Article 57(8) of Regulation (EU) No 168/2013 and set out in Annex III to this regulation;

  8. 1.1.8.

    the manufacturer’s declaration of conversion of (L3e/L4e)-A2 to (L3e/L4e)-A3 motorcycle characteristics and vice versa as referred to in Article 25(8) of Regulation (EU) No 168/2013 and in point 4.2.6. of Annex III to Commission Delegated Regulation (EU) No 44/2014 of 21 November 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to the vehicle construction and general requirements for the approval of two- or three- wheel vehicles and quadricyclesf2, as set out in Appendix 24 of this Annex;

  9. 1.1.9.

    the manufacturer’s declaration on powertrain tampering prevention measures (anti-tampering) as referred to in Article 20(2) of Regulation (EU) No 168/2013 and in points 2.2., 2.6. and 5.2. of Annex II to Commission Delegated Regulation 44/2014 according to the models established in Appendix 25 of this Annex;

  10. 1.1.10.

    any additional information requested by the approval authority as part of the approval procedure.

1.2

Applications submitted on paper shall be in triplicate. Any drawings shall be to an appropriate scale and in sufficient detail on size A4 sheets or in a folder of A4 format. Photographs, if any, shall show sufficient detail.

1.3

If the systems, components or separate technical units have electronic controls, information concerning their performance shall be provided.

Informationon the type-approval procedure chosen in accordance with Article 25(1) of Regulation (EU) No 168/2013

A duly completed version of this statement shall be included in the information folder.

The undersigned: [… (full name and position)]

Company name and address of the manufacturer: …

Name and address of the manufacturer’s representative (if any): …

Hereby applies for type-approval procedure(4):

  1. (a)

    step-by-step type-approval

  2. (b)

    single-step type-approval

  3. (c)

    mixed type-approval

Where procedures (a) or (c) are chosen, compliance with requirements as under (b) is declared for all systems, components and separate technical units.

Multi-stage type-approval chosen in accordance with Article 25(5) of Regulation (EU) No 168/2013: yes/no(4)

Information on the vehicle(s) to be filled in, if application is for EU whole-vehicle type-approval(3) :

  1. 0.1.

    Make (trade name of the manufacturer): …

  2. 0.2.

    Type(17): …

    1. 0.2.1.

      Variant(s)(17): …

    2. 0.2.2.

      Version(s)(17): …

    3. 0.2.3.

      Commercial name(s) (if available): …

  3. 0.3.

    Category, subcategory and sub-subcategory of vehicle(2): …

Information to be filled in, if application is for type-approval of a system/ component/separate technical unit(3)(4) :

  1. 0.7.

    Make(s) (trade name(s) of manufacturer): …

  2. 0.8.

    Type: …

    1. 0.8.1.

      Commercial name(s) (if available): …

  3. 1.6.

    Virtual and/or self-testing(3)

    1. 1.6.1.

      Overview list with virtual and/or self-tested systems, components or separate technical units pursuant to point 6 of Annex III to Commission Delegated Regulation (EU) No 44/2014 below:

      Overview table virtual and/or self-testing

      Commission Delegated Regulation (EU) No 134/2014 of 16 December 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to environmental and propulsion unit performance requirements and amending Annex V thereof (OJ L 53, 21.2.2014, p. 1).
      Delegated actAnnexSubjectVirtual and/or self-tested: yes/no(4)
      Commission Delegated Regulation (EU) No 134/2014f1 IXTesting procedures on maximum design vehicle speedSelf-testing: yes/no(4)
      Commission Delegated Regulation (EU) No 3/2014IIAudible warning devicesSelf-testing: yes/no(4)
      Commission Delegated Regulation (EU) No 3/2014VIIIDriver-operated controls including identification of controls, tell-tales and indicatorsSelf-testing: yes/no(4)
      Commission Delegated Regulation (EU) No 3/2014IXInstallation of lighting and light- signalling devicesVirtual testing: yes/no(4)
      Commission Delegated Regulation (EU) No 3/2014XRearward visibilityVirtual testing: yes/no(4)
      Commission Delegated Regulation (EU) No 3/2014XIVInstallation of tyresVirtual testing: yes/no(4)
      Commission Delegated Regulation (EU) No 44/2014XIVRegistration plate spaceSelf & Virtual testing: yes/no(4)
      Commission Delegated Regulation (EU) No 44/2014XVIStandsSelf-testing: yes/no(4)
      This Commission Implementing RegulationVIIIStatutory plate and EU type-approval markSelf-testing: yes/no(4)
    2. 1.6.2.

      Detailed report on validation of virtual and/or self-testing added: yes/no(4)

Place: …Date: …
Signature: …Name and position in the company: …

1.1

The information document shall have a reference number supplied by the applicant.

1.2

Where the particulars appearing in the information document for vehicle approval have changed, the manufacturer shall submit revised pages to the approval authority showing clearly the nature of the change(s) and the date of re-issue.

1.3.1The manufacturer shall supply the information required by the following table in respect of the applicable subjects for the vehicle in Annex II to Regulation (EU) No 168/2013. All relevant approvals and test reports (if available) for each subject shall be included. However, information in respect of systems, components or separate technical units need not be given here so long as such information is included in the correspondent approval certificate.

Type-approval number and test report overview

Contracting parties to the Revised 1958 Agreement.

To be indicated if not obtainable from the type-approval number.

The approval authority shall complete the references for the test reports, established by regulatory acts, for which no type-approval certificate is available.
Item number and subjectType-approval number or test report numberf1 Date of issue of the type-approval or of its extension or of the test reportMember State or contracting partyf2 issuing the type- approvalf3 or technical service issuing the test report Reference to the regulatory act and its latest amendmentVariant(s)/ version(s

e.g.

B1 audible warning devices

Signed: …
Position in company: …
Date: …

1.4F1

Vehicles and Vehicle types shall be identified as compliant with environmental step Euro 5 or environmental step Euro 5+ in accordance with the following Table:

Identification of environmental step Euro 5 and Euro 5+ for L-category vehicles

(sub-) category Obligatory as of: 1.1.2020 for new types of vehicles 1.1.2021 for existing types of vehicles Envi. step Obligatory as of: 1.1.2024 for new types of vehicles 1.1.2025 for existing types of vehicles Envi. step
L1e OBD system not required Euro 5 OBD system not required Euro 5
test types I, IV & V: Euro 5 test types I, IV & V: Euro 5
L2e (other than L2e-U) OBD system not required Euro 5 OBD system not required Euro 5
test types I, IV & V: Euro 5 test types I, IV & V: Euro 5
L2e-U OBD system not required Euro 5 OBD system not required Euro 5+
test type I: Euro 4 test type I: Euro 5
test type IV & V: Euro 5 test types IV & V: Euro 5
L3e (other than enduro and trial), L4e, L5e-A and L7e-A OBD stage I system that monitors electric circuit and electronics failure, and triggers a report when: Euro 5 OBD stage I system that monitors electric circuit and electronics failure, and triggers a report when: Euro 5+
  1. (a)

    OBD emission thresholds of Annex VI (B1) to Regulation (EU) No 168/2013 are exceeded, and

  1. (a)

    OBD emission thresholds of Annex VI (B2) to Regulation (EU) No 168/2013 are exceeded, and

  1. (b)

    any operating mode significantly reduces engine torque.

  1. (b)

    any operating mode significantly reduces engine torque.

OBD stage II that monitors emission control system failures and degradation (with the exception of catalyst monitoring), and reports when: OBD stage II that monitors emission control system failures and degradation, and reports when:
OBD emission thresholds of Annex VI (B1) to Regulation (EU) No 168/2013 are exceeded. OBD emission thresholds of Annex VI (B2) to Regulation (EU) No 168/2013 are exceeded.
test types I, IV & V: Euro 5 test types I, IV & V: Euro 5
Enduro L3e-AxE and Trial L3e-AxT OBD stage I system that monitors electric circuit and electronics failure, and triggers a report when: Euro 5 OBD stage I system that monitors electric circuit and electronics failure, and triggers a report when: Euro 5+
  1. (a)

    OBD emission thresholds of Annex VI (B1) to Regulation (EU) No 168/2013 are exceeded, and

  1. (a)

    OBD emission thresholds of Annex VI (B2) to Regulation (EU) No 168/2013 are exceeded, and

  1. (b)

    any operating mode significantly reduces engine torque.

  1. (b)

    any operating mode significantly reduces engine torque.

test type I: Euro 4 test type I: Euro 5
test types IV & V: Euro 5 test types IV & V: Euro 5
L5e (other than Le5-A) and L7e (other than L7e-A) OBD stage I system that monitors electric circuit and electronics failure, and triggers a report when: Euro 5 OBD stage I system that monitors electric circuit and electronics failure, and triggers a report when: Euro 5+
  1. (a)

    OBD emission thresholds of Annex VI (B1) to Regulation (EU) No 168/2013 are exceeded, and

  1. (a)

    OBD emission thresholds of Annex VI (B2) to Regulation (EU) No 168/2013 are exceeded, and

  1. (b)

    any operating mode significantly reduces engine torque.

  1. (b)

    any operating mode significantly reduces engine torque.

test types I, IV & V: Euro 5 test types I, IV & V: Euro 5
L6e other than L6e-B OBD system not required Euro 5 OBD system not required Euro 5
test types I, IV & V: Euro 5 test types I, IV & V: Euro 5
L6e-B OBD system not required Euro 5 OBD system not required Euro 5+
test type I: Euro 4 test type I: Euro 5
test type IV & V: Euro 5 test type IV & V: Euro 5

2Content of the information document

All information documents shall contain the following:

2.1

For a whole vehicle type-approval the manufacturer shall complete:

  • the matrix in point 2.3. to identify the versions and variants of the vehicle intended for type-approval;

  • a list of items applicable to the (sub-)category and to the technical characteristics of the vehicle from which content has been extracted, adhering to the numbering system of the total list set out in point 2.6.

2.2

For a system, component or separate technical unit as listed in table 1 the manufacturer shall complete the applicable appendix to this Annex.

In addition to the Annexes mentioned in table 1, the systems, components and separate technical units shall comply with the following requirements:

  • arrangements for type-approval procedures (Annex III of Commission Delegated Regulation (EU) No 44/2014)

  • conformity of production (CoP) (Annex IV of Delegated Regulation (EU) No 44/2014)

  • access to repair and maintenance information (Annex XV of Delegated Regulation (EU) No 44/2014)

Table 1

Lists of systems, components and separate technical units which may be subject to an EU type-approval

LIST I — Environmental and propulsion unit performance requirements
AppendixSystem or component/separate technical unit (STU)Commission Delegated Regulation (EU) No 134/2014 Annex numberAs amended by and/or at the stage of implementation
1System: tailpipe pollution-control systemII, III, V, VI
2System: crankcase and evaporative emissionsIV, V
3System: environmental and functional on-board diagnostic (OBD)

VIII

(and Annex XII to Commission Delegated Regulation (EU) No 44/2014)

4System: sound levelIX
5System: propulsion unit performanceX
F15a System: maximum torque and a maximum net power of a propulsion unit

X

Appendix 2

6STU: pollution-control deviceII, III, IV, V, VI
7STU: noise-abatement deviceIX
8STU: exhaust device (pollution-control device and noise-abatement device)II, III, V, VI, IX
LIST II — Vehicle functional safety requirements
AppendixSystem or component/separate technical unit (STU)Commission Delegated Regulation (EU) No 3/2014 Annex numberAs amended by and/or at the stage of implementation
8a System: installation of audible warning devices II
9System: brakingIII
9a System: installation of glazing, windscreen wipers and defrosting and demisting devices VII
9b System: identification of controls, tell-tales and indicators VIII
10System: installation of lighting and light-signalling devicesIX
11System: Roll-over protective structure (ROPS)XI
11a System: safety belt anchorages XII
11b System: steer-ability, cornering properties and turn ability XIV
12System: installation of tyresXV
13Component: audible warning deviceII
13a System: vehicle occupant protection, including interior fittings, head restraint and vehicle doors XVII
14Component/STU: non-glazing front windscreenVII
15Component/STU: windscreen washer deviceVII
16Component/STU: rearward visibility deviceX
17STU: safety beltsXII
18Component/STU: seating position (saddle/seat)XIII
LIST III — Vehicle construction and general type-approval requirements
AppendixSystem or component/separate technical unit (STU)Commission Delegated Regulation (EU) No 44/2014 Annex numberAs amended by and/or at the stage of implementation
19STU: trailer coupling deviceV
20STU: devices to prevent unauthorised useVI
20a STU: fuel tank IX
21STU: passenger handholdsXIII
22STU: footrestsXIII
23STU: side-car

VIII, XI, XIII;

(and Annexes III, V, VII, IX, X, XII, XIII, XIV, XV, XVII and XIX to Commission Delegated Regulation (EU) No 3/2014)

2.3

Matrix showing the combinations of the entries listed in point 2.6. within the versions and variants of the vehicle type

Variants and version matrix

Item NoAllVersion 1Version 2Version 3Version n

2.3.1

A separate matrix shall be compiled for each variant within the type.

2.3.2

Entries with no restrictions on their combination within a variant shall be listed in the column headed ‘All’.

2.3.3

The above information may be presented in an alternative format or merged with the information supplied under point 2.6.

2.4.1

The manufacturer shall allocate an alphanumeric code to each vehicle type, variant and version, made up of Roman letters and/or Arabic numerals, which shall also be indicated in the certificate of conformity (see Annex IV) of the vehicle concerned.

The use of brackets and hyphens is permitted provided they do not replace a letter or a numeral.

2.4.2

The whole code shall be designated: Type-Variant-Version or ‘TVV’.

2.4.3

The TVV shall clearly and unequivocally identify a unique combination of technical features in relation to the criteria defined in Part B of this Annex.

2.4.4

The same manufacturer may use the same code in order to define a vehicle type when the latter falls in two or more categories.

2.4.5

The same manufacturer shall not use the same code in order to define a vehicle type for more than one type-approval within the same vehicle category.

2.4.6.1The number of characters shall not exceed:

  1. a..

    15 for the code of the vehicle type;

  2. b..

    25 for the code of one variant;

  3. c..

    35 for the code of one version.

2.4.6.2

The complete alphanumeric ‘TVV’ shall not contain more than 75 characters.

2.4.6.3When the TVV is used as a whole, a space shall be left between the type, the variant and the version.

Example of such TVV: 159AF[… space]0054[… space]977K(BE).

2.5

For those subjects referred to in Annex II to Regulation (EU) No 168/2013 whose approvals have been granted in accordance with the UNECE regulations referred to in Article 54 of Regulation (EU) 168/2013 (UNECE approvals), the manufacturer shall supply the information required in point 2.7. only if it is not already provided in the correspondent approval certificate and/or test report. However, the information referred to in the certificate of conformity (Annex IV) shall be supplied in any case.

2.6

The manufacturer shall complete the applicable item numbers of the template set out in point 2.8. and submit this filled-out list to the approval authority that grants the type-approval, split into two separate documents. The applicable items marked with * shall remain with the approval authority that grants the type-approval and all other applicable items shall make part of the information folder. The Colum ‘(Sub) categories’ indicates to which sub-categories applies each particular entry (e.g. ‘L1e - L7e’ means that the entry applies to all categories and subcategories).

2.7

The following type of data entries may be omitted in the information document under the condition that an appropriate technical drawing either as a paper document or a pdf-file is added to the information folder and on which these listed items are shown in a clear and readable way:

  1. 2.7.1.

    Make (with the exemption of Item No 0.1);

  2. 2.7.2.

    Type (with the exemption of Item No 0.2);

  3. 2.7.3.

    Location / where;

  4. 2.7.4.

    Working principle (with the exemption of Item No 3.2.1.2);

  5. 2.7.5.

    Characteristics;

  6. 2.7.6.

    Number of (with the exemption of Items No 1.3., 3.2.1.1. and 6.16.1.);

  7. 2.7.7.

    Identification / part number;

  8. 2.7.8.

    (Brief) / (Technical) description;

  9. 2.7.9.

    Design;

  10. 2.7.10.

    Schematic drawing / diagram;

  11. 2.7.11.

    (Construction) materials used;

  12. 2.7.12.

    Angles / inclination and other dimensions (height, length, width, distance) (with the exemption of Items No 2.2.1., 2.2.2., 2.2.3., 2.2.17., 7.6.1. and 7.6.2.);

  13. 2.7.13.

    Tolerance;

  14. 2.7.14.

    Reference mark;

  15. 2.7.15.

    Size (with the exemption of point 6.18.1.1.1., 6.18.1.1.2. and 6.18.1.1.3.);

  16. 2.7.16.

    Configuration.

2.8INFORMATION DOCUMENT DATA ENTRIES

OJ L 72, 14.3.2008, p. 1.

OJ L 120, 7.5.2011, p. 1.

Regulation (EC) No 79/2009 of the European Parliament and of the Council of 14 January 2009 on type-approval of hydrogen-powered motor vehicles, and amending Directive 2007/46/EC (OJ L 35, 4.2.2009, p. 32).

OJ L 120, 7.5.2011, p. 1.

OJ L 72, 14.3.2008, p. 1.
Item No.(Sub) categoriesDetailed information
0. GENERAL INFORMATION
A. General information concerning vehicles
0.1. L1e — L7e Make (trade name of manufacturer): …
0.2. L1e — L7e Type(17) : …
0.2.1L1e — L7eVariant(s)(17): …
0.2.2L1e — L7eVersion(s)(17): …
0.2.3.L1e — L7eCommercial name(s) (if available): …
0.3. L1e — L7e Category, subcategory and sub-subcategory of vehicle(2) : …
0.4. L1e — L7e Company name and address of manufacturer: …
0.4.1.L1e — L7eName(s) and address(es) of assembly plants: …
0.4.2.L1e — L7eName and address of manufacturer’s authorised representative, if any: …
0.5. L1e — L7e Manufacturer’s statutory plate(s): …
0.5.1.L1e — L7eLocation of the manufacturer's statutory plate(15)(18): …
0.5.2.L1e — L7eMethod of attachment: …
0.5.3.L1e — L7ePhotographs and/or drawings of the statutory plate (completed example with dimensions): …
0.6. L1e — L7e Location of the vehicle identification number(15) : …
0.6.1.L1e — L7ePhotographs and/or drawings of the locations of the vehicle identification number (completed example with dimensions): …
0.6.1.1.L1e — L7eThe serial number of the type begins with: …
B. General information concerning systems, components or separate technical units
0.7.L1e — L7e Make(s) (trade name(s) of manufacturer): …
0.8. L1e — L7e Type: …
0.8.1.L1e — L7eCommercial name(s) (if available): …
0.8.2.L1e — L7eType-approval number(s) (if available): …
0.8.3.L1e — L7eType-approval(s) issued on (date, if available): …
0.9.L1e — L7e Company name and address of manufacturer: …
0.9.1.L1e — L7eName(s) and address(es) of assembly plants: …
0.9.2.L1e — L7eName and address of manufacturer’s authorised representative, if any: …
0.10. Vehicle(s) for which the system/separate technical unit is intended for(21) : …
0.10.1.L1e — L7eType(17): …
0.10.2.L1e — L7eVariant(17): …
0.10.3.L1e — L7eVersion(17): …
0.10.4.L1e — L7eCommercial name(s) (if available): …
0.10.5.L1e — L7eCategory, subcategory and sub-subcategory of vehicle(2): …
0.11.L1e — L7e Type-approval marks for components and separate technical units(19) : …
0.11.1.L1e — L7eMethod of attachment: …
0.11.2.L1e — L7ePhotographs and/or drawings of the location of the type-approval mark (completed example with dimensions): …
C. General information regarding conformity of production and access to repair and maintenance information
0.12. Conformity of production
0.12.1.L1e — L7eDescription of overall quality-assurance management systems.
0.13. Access to repair and maintenance information
0.13.1.L1e — L7eAddress of principal website for access to vehicle repair and maintenance information: …
0.13.2.L1e — L7eIn the case of multi-stage type-approval, address of principal website for access to vehicle repair and maintenance information from manufacturer(s) at previous stage(s):
1. GENERAL CONSTRUCTION CHARACTERISTICS
1.1.L1e — L7ePhotographs and/or drawings of a representative vehicle: …
1.2.L1e — L7eScale drawing of the whole vehicle: …
1.3.L1e — L7eNumber of axles and wheels: …
1.3.1.L1e — L7eAxles with twinned wheels(23): …
1.3.2.L1e — L7ePowered axles(23): …
1.4.L1e — L7eChassis (if any) (overall drawing): …
1.5.L2e, L5e-B, L6e-B, L7e-A2, L7e-B2, L7e-CMaterial used for the bodywork:
1.6.L1e — L7ePosition and arrangement of the propulsion(s): …
1.7.L4e, L5e-B, L6e-B, L7e-A2, L7e-B2, L7e-CHand of drive: left/right/centre(4): …
1.7.1.L1e — L7eVehicle is equipped to be driven in right/left-hand traffic and in countries that use metric/metric and imperial units.(4): …
1.8. Propulsion unit performance
1.8.1.L3e, L4e, L5e, L7e-A, L7e-B2Declared maximum vehicle speed: … km/h
1.8.2.L1e, L2e, L6e, L7e-B1, L7e-CMaximum design vehicle speed (22): … km/h and gear in which it is reached: …
1.8.3.L1e — L7eMaximum net power combustion engine: … kW at … min-1 at A/F ratio: …
1.8.4.L1e — L7eMaximum net torque combustion engine: … Nm at … min-1 at A/F ratio: …
1.8.5.L1e — L7eMaximum continuous-rated power electric motor (15/30(4) minutes power(27)): … kW at … min–1
1.8.6.L1e — L7eMaximum continuous-rated torque electric motor: … Nm at … min-1
1.8.7.L1e — L7eMaximum continuous total power for propulsion(s): …. kW at …. min-1 at A/F ratio: …
1.8.8.L1e — L7eMaximum continuous total torque for propulsion(s): … Nm at … min-1 at A/F ratio: …
1.8.9.L1e — L7eMaximum peak power for propulsion(s): … kW at … min-1at A/F ratio: …
2.

MASSES AND DIMENSIONS

(in kg and mm.) refer to drawings where applicable

2.1 Range of vehicle mass (overall)
2.1.1.L1e — L7eMass in running order: … kg
2.1.1.1.L1e — L7eDistribution of mass in running order between the axles: … kg
2.1.2.L1e — L7eActual mass: … kg
2.1.2.1.L1e — L7eDistribution of actual mass between the axles: … kg
2.1.3.L1e — L7eTechnically permissible maximum laden mass: … kg
2.1.3.1.L1e — L7eTechnically permissible maximum mass on front axle: … kg
2.1.3.2.L1e — L7eTechnically permissible maximum mass on rear axle: … kg
2.1.3.3.L4eTechnically permissible maximum mass on sidecar axle: … kg
2.1.4.L1e — L7eMaximum hill-starting ability at the maximum technically permissible mass declared by the manufacturer: … % slope
2.1.5.L1e — L7eMaximum pay mass declared by manufacturer: … kg
2.1.6.L1e — L7eSafe load carrying capacity of load platform declared by manufacturer: … kg
2.1.7.L1e — L7eTechnically permissible maximum towable mass in case of (4): Braked: … kg Unbraked: … kg
2.1.7.1L1e — L7eTechnically permissible maximum laden mass of the combination: … kg
2.1.7.2.L1e — L7eTechnically permissible maximum mass at the coupling point: … kg
2.1.8.L1e — L7eMass of the optional equipment: … kg
2.1.9.L1e — L7eMass of the superstructure: … kg
2.1.10.L1e — L7eMass of the propulsion battery: … kg
2.1.11.L2e, L4e, L5e, L6e, L7eMass of the doors: … kg
2.1.12.L2e-U, L5e-B, L6e-BU, L7e-CUMass of the machines or equipment installed on the load platform area: … kg
2.1.13.L1e — L7eMass of the gaseous fuel system as well as storage tanks for gaseous fuel: … kg
2.1.14.L1e — L7eMass of the storage tanks to store compressed air: … kg
2.2. Range of vehicle dimensions (overall)
2.2.1.L1e — L7eLength: … mm
2.2.2.L1e — L7eWidth: … mm
2.2.3.L1e — L7eHeight: … mm
2.2.4.L1e — L7eWheelbase: … mm
2.2.4.1.L4eWheelbase sidecar(28): … mm
2.2.5.Track width
2.2.5.1.

L1e — L7e if equipped with twinned wheels

L2e, L4e, L5e, L6e, L7e

Track width front: … mm.
2.2.5.2.L1e — L7e if equipped with twinned wheelsTrack width rear: … mm.
2.2.5.3.L2e, L4e, L5e, L6e, L7eTrack width sidecar: … mm.
2.2.6.L7e-BFront overhang: … mm.
2.2.7.L7e-BRear overhang: … mm.
2.2.8.Load platform dimensions
2.2.8.1.L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CULength of the load platform: … mm.
2.2.8.2.L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CUWidth of load platform: … mm.
2.2.8.3.L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CUHeight of load platform: … mm.
2.2.9.Centre of gravity
2.2.9.1.L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CULocation of the centre of gravity forward of the rear axle Lcg: … mm.
2.2.9.2.L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CULocation of the centre of gravity above the ground plane Hcg: … mm.
2.2.9.3.L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CULocation centre of gravity of loaded platform forward of the rear axle LcgLP: … mm.
2.2.10.Miscellaneous dimensions
2.2.10.1.L7e-B2Approach angle(11): … degrees.
2.2.10.2.L7e-B2Departure angle(11): … degrees.
2.2.10.3.L7e-B2Ramp angle(11): … degrees.
2.2.10.4.L7e-B2Ground clearance under the front axle(11): … mm.
2.2.10.5.L7e-B2Ground clearance under the rear axle(11): … mm.
2.2.10.6.

L3e-AxE (x=1, 2 or 3), L3e-AxT (x=1, 2 or 3)

L7e-B

Ground clearance between the axles(11): … mm.
2.2.10.7.L7e-BWheelbase to ground clearance ratio … [no unit]
2.2.10.8.L7e-B2Static stability coefficient — Kst: … [no unit]
2.2.10.9.L3e-AxE, L3e-AxTSeat height: … mm
2.2.10.10.L3e-AxE, L3e-AxTGround clearance: … mm
3. GENERAL POWERTRAIN CHARACTERISTICS
3.1 Manufacturer of the propulsion unit
3.1.1. Combustion engine
3.1.1.1.L1e — L7eManufacturer: …
3.1.1.2.L1e — L7eEngine code (as marked on the engine or other means of identification): …
3.1.1.3.L1e — L7eFuel identification marking (if available): …
3.1.2. Electric motor
3.1.2.1.L1e — L7eManufacturer: …
3.1.2.2.L1e — L7eElectric motor code (as marked on the engine or other means of identification): …
3.1.3. Hybrid application
3.1.3.1.L1e — L7eManufacturer: …
3.1.3.2.L1e — L7eApplication code (as marked on the engine or other means of identification): …
3.1.3.3.L1e — L7eFuel identification marking (if available): …
3.1.3.4.L1e — L7ePhotographs and/or drawings of the location of the code(s) and/or type-approval numbers (completed example with dimensions)(20): …
3.2. Combustion engine
3.2.1. Specific engine information
3.2.1.1.L1e — L7eNumber of combustion engines: …
3.2.1.2.L1e — L7eWorking principle: internal combustion engine (ICE)/positive ignition/compression ignition /external combustion engine (ECE)/turbine/compressed air(4): …
3.2.1.3.L1e — L7eCycle: four-stroke/two-stroke/rotary/other(4): …
3.2.1.4.L1e — L7eCylinders
3.2.1.4.1.L1e — L7eNumber: …
3.2.1.4.2.L1e — L7eArrangement(26): …
3.2.1.4.3.L1e — L7eBore(12): … mm
3.2.1.4.4.L1e — L7eStroke(12): … mm
3.2.1.4.5.L1e — L7eNumber and configuration of stators in the case of rotary-piston engine: …
3.2.1.4.6.L1e — L7eVolume of combustion chambers in the case of rotary-piston engine: … cm3
3.2.1.4.7.L1e — L7eFiring order: …
3.2.1.5.L1e — L7eEngine capacity(6): … cm3
3.2.1.6.L1e — L7eVolumetric compression ratio(7): …
3.2.1.7.L1e — L7eNumber of inlet and exhaust valves
* 3.2.1.7.1.L1e — L7eNumber and minimum cross-sectional areas of inlet and outlet ports: …
* 3.2.1.7.2.L1e — L7eValve timing or equivalent data: …
* 3.2.1.7.3.L1e — L7eMaximum lift of valves, angles of opening and closing, or timing details of alternative distribution systems, in relation to dead centres. For variable timing system, minimum and maximum timing: …
* 3.2.1.7.4.L1e — L7eReference and/or setting ranges(4): …
3.2.1.8.L1e — L7eDrawings of combustion chamber, cylinder head, piston, piston rings: …
3.2.1.9.L1e — L7eNormal warm engine idling speed: … min-1
3.2.1.10.L1e — L7eStop-start system: yes/no(4)
* 3.2.2. Powertrain/propulsion/drive-train management system
3.2.2.1.L1e — L7ePCUs/ECUs(4) software identification number(s): … and calibration verification number(s): …
3.2.3. Fuel
3.2.3.1.L1e — L7eFuel type: (9)
3.2.3.2.L1e — L7eVehicle fuel configuration: mono-fuel/bi- fuel/flex fuel(4)
3.2.3.2.1.L1e — L7eMaximum amount of bio-fuel acceptable in fuel: … % by volume
3.2.4. Fuel pressure delivery and control
3.2.4.1.L1e — L7eBrief description and schematic drawing of low-and/or high-pressure fuelling wet system(s)(4): …
3.2.4.2.L1e — L7eLow- and/or high-pressure fuel pump(s): yes/no(4)
3.2.4.2.1.L1e — L7eFuel pump control: mechanical/on/off electric/continuous operation/electronically controlled variable operation(4): …
3.2.4.2.2.L1e — L7e

For CI combustion engines and dual fuel engines only maximum fuel delivery (4)(7): … g/s or mm3/stroke or cycle at an engine speed of:…min-1 or, alternatively, a characteristic diagram: …

(When boost control is supplied, state the characteristic fuel delivery and boost pressure versus engine speed)

3.2.4.3.L1e — L7eCommon rail: yes/no(4)
3.2.4.4.L1e — L7eFuel distributor/rail/hoses(4): yes/no(4)
3.2.4.5.L1e — L7eFuel pressure and/or fuel flow regulator(s): yes/no(4)
3.2.5. Fuel mass metering and control
3.2.5.1.L1e — L7eBy carburettor(s): yes/no(4)
* 3.2.5.1.1.L1e — L7eOperating principle and construction: …
* 3.2.5.1.2.L1e — L7eMaximum fuel-flow rate: … g/s at maximum power and torque: …
3.2.5.1.3.L1e — L7eCarburettor(s) settings(7): …
* 3.2.5.1.4.L1e — L7eCarburettor diffusers: …
* 3.2.5.1.5.L1e — L7eCarburettor fuel-level in float chamber: …
* 3.2.5.1.5.1.L1e — L7eCarburettor mass of float: …
3.2.5.1.6.L1e — L7eCarburettor cold-starting system: manual/automatic(4): yes/no(4)
3.2.5.1.6.1.L1e — L7eCarburettor cold-starting system operating principle(s): …
3.2.5.1.7.L1e — L7eMixture scavenging port: yes/no(4)
3.2.5.1.7.1.L1e — L7eMixture scavenging port dimensions: …
3.2.5.2.L1e — L7eBy mechanically/hydraulically controlled fuel injection(4): yes/no(4)
3.2.5.2.1.L1e — L7eOperation principle: …
3.2.5.2.2.L1e — L7eMechanical/electronic(4) adjustment of maximum fuel mass delivery: yes/no(4)
3.2.5.3.L1e — L7eBy electronically controlled fuel injection system: yes/no(4)
3.2.5.3.1.L1e — L7eOperation principle: port injection/direct injection/pre-chamber/swirl chamber(4): …
3.2.5.3.2.L1e — L7eFuel injector(s): single-/multi-point/direct injection/other (specify) (4): …
3.2.5.3.3.L1e — L7eTotal and per cylinder amount of fuel injectors: …
3.2.5.4.L1e — L7eAir-assisted fuel injector: yes/no(4): …
3.2.5.4.1.L1e — L7eDescription and operating pressure of air-assist: …
3.2.5.5.L1e — L7eCold start system: yes/no(4)
3.2.5.5.1.L1e — L7eDescription of cold start system: …
3.2.5.6.L1e — L7eAuxiliary starting aid: yes/no(4)
3.2.5.7.L1e — L7eCI injection specific: yes/no
3.2.5.7.1.L1e — L7eStatic injection timing(7): …
3.2.5.7.2.L1e — L7eInjection advance curve(7): …
3.2.6. Gaseous fuelling system and control
3.2.6.1.L1e — L7eBrief description and schematic drawing of gaseous fuelling system(s): …
3.2.6.2.L1e — L7eLiquefied petroleum gas (LPG) fuelling system: yes/no(4)
3.2.6.2.1.L1e — L7eType-approval number according to UNECE Regulation No 67f1: …
3.2.6.2.2.L1e — L7eElectronic engine management control unit for LPG fuelling: yes/no(4)
3.2.6.2.2.1.L1e — L7eEmission-related adjustment possibilities: …
3.2.6.2.3.L1e — L7eFurther documentation: …
* 3.2.6.2.3.1L1e — L7eDescription of the safeguarding of the catalyst at switch-over from petrol to LPG or back: …
3.2.6.2.3.2L1e — L7eSystem layout (electrical connections, vacuum connections, compensation hoses, etc.): …
3.2.6.2.4.L1e — L7eDrawing of the symbol: …
3.2.6.3.L1e — L7eNatural gas (NG) fuelling system: yes/no(4)
3.2.6.3.1.L1e — L7eType-approval number according to UNECE Regulation No 110f2: …
3.2.6.3.2.L1e — L7eElectronic engine management-control unit for NG fuelling: yes/no(4)
3.2.6.3.2.1.L1e — L7eEmission-related adjustment possibilities: …
3.2.6.3.3.L1e — L7eFurther documentation: …
* 3.2.6.3.3.1.L1e — L7eDescription of the safeguarding of the catalyst at switch-over from petrol to NG or back: …
3.2.6.3.3.2.L1e — L7eSystem layout (electrical connections, vacuum connections compensation hoses, etc.): …
3.2.6.3.4.L1e — L7eDrawing of the symbol: …
3.2.6.4.L1e — L7eGaseous fuel: LPG/NG-H/NG-L/NG-HL(4): yes/no(4)
3.2.6.4.1.L1e — L7ePressure regulator(s) or vaporiser/pressure regulator(s)(4)
* 3.2.6.4.1.1.L1e — L7eNumber of pressure reduction stages: …
3.2.6.4.1.2.L1e — L7ePressure in final stage, minimum: … kPa — maximum: … kPa
3.2.6.4.1.3.L1e — L7eNumber of main adjustment points: …
3.2.6.4.1.4.L1e — L7eNumber of idle adjustment points: …
3.2.6.4.1.5.L1e — L7eType-approval number: …
3.2.6.4.2.L1e — L7eFuelling system: mixing unit/gas injection/liquid injection/direct injection(4)
* 3.2.6.4.2.1.L1e — L7eMixture strength regulation: …
3.2.6.4.2.2.L1e — L7eSystem description and/or diagram and drawings: …
3.2.6.4.2.3.L1e — L7eType-approval number: …
3.2.6.4.3.L1e — L7eMixing unit: yes/no(4)
3.2.6.4.3.1.L1e — L7eNumber: …
3.2.6.4.3.2.L1e — L7eLocation: …
3.2.6.4.3.3.L1e — L7eAdjustment possibilities: …
3.2.6.4.3.4.L1e — L7eType-approval number: …
3.2.6.4.4.L1e — L7eInlet manifold injection: yes/no(4)
3.2.6.4.4.1.L1e — L7eInjection: single-point/multi-point(4)
3.2.6.4.4.2.L1e — L7eInjection: continuous/simultaneously timed/sequentially timed(4)
3.2.6.4.5.L1e — L7eInjection equipment: yes/no(4)
3.2.6.4.5.1.L1e — L7eAdjustment possibilities: …
3.2.6.4.5.2.L1e — L7eType-approval number: …
3.2.6.4.6.L1e — L7eSupply pump: yes/no(4)
3.2.6.4.6.1.L1e — L7eType-approval number: …
3.2.6.4.7.L1e — L7eInjector(s): …
3.2.6.4.7.1.L1e — L7eType-approval number: …
3.2.6.4.8.L1e — L7eDirect/port injection: yes/no(4)
3.2.6.4.9.L1e — L7eInjection pump/pressure regulator: yes/no (4)
3.2.6.4.9.1.L1e — L7eType-approval number: …
3.2.6.4.10.L1e — L7eSeparate electronic control unit (ECU) for gaseous fuelling system: yes/no(4)
3.2.6.4.10.1.L1e — L7eAdjustment possibilities: …
3.2.6.4.10.2.L1e — L7eSoftware identification number(s): …
3.2.6.4.10.3.L1e — L7eCalibration verification number(s): …
3.2.6.5.L1e — L7eNG fuel-specific equipment: …
3.2.6.5.1.L1e — L7eVariant 1 (only in the case of approvals of engines for several specific fuel compositions): …
3.2.6.5.2.L1e — L7eFuel composition:

Overview

methane (CH4):basis: …%molemin. …%molemax. …%mole
ethane (C2H6):basis: …%molemin. …%molemax. …%mole
propane (C3H8):basis: …%molemin. …%molemax. …%mole
butane (C4H10):basis: …%molemin. …%molemax. …%mole
C5/C5+:basis: …%molemin. …%molemax. …%mole
oxygen (O2):basis: …%molemin. …%molemax. …%mole
inert (N2, He, etc.):basis: …%molemin. …%molemax. …%mole
3.2.6.5.3.L1e — L7eGaseous fuel injector(s): …
3.2.6.5.4.L1e — L7eVariant 2 (only in the case of approvals for several specific fuel compositions): …
3.2.6.6.L1e — L7eHydrogen fuel-specific equipment: yes/no(4)
3.2.6.6.1.L1e — L7eEC type-approval number according to Regulation (EC) No 79/2009 of the European Parliament and of the Councilf3: …
* 3.2.6.6.2.L1e — L7eFurther documentation
3.2.6.6.3.L1e — L7eSystem layout (electrical connections, vacuum connections, compensation hoses, etc.): …
* 3.2.6.6.4.L1e — L7eDescription of the safeguarding of the catalyst at switch-over from petrol to hydrogen/H2NG(4) or back: …
3.2.6.6.5.L1e — L7eDrawing of the symbol: …
3.2.6.7.L1e — L7eH2NG fuelling system: yes/no(4)
3.2.6.7.1.L1e — L7ePercentage of hydrogen in the fuel (the maximum specified by the manufacturer): …
3.2.7. Air-induction system
3.2.7.1.L1e — L7eBrief description and schematic drawing of gaseous intake air-flow and induction system: …
3.2.7.2.L1e — L7eIntake manifold description and working principle (e.g. fixed length/variable length/swirl valves)(4) (include detailed drawings and/or photos): …
* 3.2.7.2.1.L1e — L7eDescription and drawings of inlet pipes and their accessories (plenum chamber, heating device with control strategy, additional air intakes, etc.): …
3.2.7.3.L1e — L7eIntake air pressure charger: yes/no(4)
3.2.7.3.1.L1e — L7eBrief description and schematic drawing of the intake air-pressure charger system: …
3.2.7.3.2.L1e — L7eWorking and control principles: …
3.2.7.3.3.L1e — L7eType(s) (turbo or supercharger, other)(4): …
3.2.7.3.4.L1e — L7eMaximum intake air-charge pressure and flow-rate at maximum torque and power: … kPa and g/s or charge pressure and flow-rate map: … kPa and g/s
3.2.7.4.L1e — L7eWaste gate: yes/no(4)
3.2.7.5.L1e — L7eIntercooler: yes/no(4)
3.2.7.5.1.L1e — L7eType: air-air/air-water/other(4)
* 3.2.7.5.2.L1e — L7eIntake depression at rated engine speed and at 100 % load (compression ignition engines only): … kPa
3.2.7.6.L1e — L7eAir filter, (drawings, photographs): …
3.2.7.7.L1e — L7eIntake air-silencer description (drawings, photographs): …
* 3.2.7.7.1.L1e — L7eWorking principle: …
3.2.8. Air-mass metering and control
3.2.8.1.L1e — L7eBrief description and schematic drawing of air-mass metering and control system: …
3.2.8.2.L1e — L7eMechanical throttle body: yes/no(4)
3.2.8.3.L1e — L7eElectronic throttle control (ETC): yes/no(4)
3.2.8.3.1.L1e — L7eSchematic drawing of electronic throttle control: …
* 3.2.8.3.1.2.L1e — L7eDescription of ETC hardware redundancies regarding sensors/actuators/electric power/ground/control electronics: …
3.2.9. Spark delivery system and control
3.2.9.1.L1e — L7eBrief description and schematic drawing of spark delivery and control system: …
3.2.9.1.1.L1e — L7eWorking principle: …
L1e — L7eIgnition advance curve or map(7) at wide open throttle: …
3.2.9.1.3.L1e — L7eStatic ignition timing (7): … degrees before TDC at maximum torque and power
3.2.9.2.L1e — L7eIon sense capability: yes/no(4)
3.2.9.3.L1e — L7eSpark plugs:
3.2.9.3.1.L1e — L7eGap setting: … mm
3.2.9.4.L1e — L7eIgnition coil(s):
* 3.2.9.4.1.L1e — L7eWorking principle: …
* 3.2.9.4.2.L1e — L7eDwell angle and timing at wide open throttle: …
3.2.10. Powertrain cooling system and control
3.2.10.1.L1e — L7eBrief description and schematic drawing of powertrain cooling and control system: …
3.2.10.2.L1e — L7eCooling system: liquid: yes/no(4)
3.2.10.2.1.L1e — L7eMaximum temperature at outlet: … K
3.2.10.2.2.L1e — L7eNominal setting of the engine temperature control mechanism: …
3.2.10.2.3.L1e — L7eNature of liquid: …
3.2.10.2.4.L1e — L7eCirculating pump(s): yes/no(4)
3.2.10.2.4.1.L1e — L7eCharacteristics: …
3.2.10.2.5.L1e — L7eDrive ratio(s): …
3.2.10.2.6.L1e — L7eDescription of the fan and its drive mechanism: …
3.2.10.3.L1e — L7eAir cooling: yes/no(4)
3.2.10.3.1.L1e — L7eReference point: …
3.2.10.3.2.L1e — L7eMaximum temperature at reference point: … K
3.2.10.3.3.L1e — L7e)Fan: yes/no(4)
3.2.10.3.3.1.L1e — L7eCharacteristics: …
3.2.10.3.3.2.L1e — L7eDrive ratio(s): …
3.2.11. Powertrain lubrication system and control
3.2.11.1.L1e — L7eBrief description and schematic drawing of powertrain lubrication and control system: …
3.2.11.2.L1e — L7eLubrication system configuration(s) (wet sump, dry sump, other, pump/injection into induction system/mixed with the fuel, etc.)(4): …
3.2.11.3.L1e — L7eLocation of oil reservoir (if any): …
3.2.11.4.L1e — L7eFeed system (pump/injection into induction system/mixed with the fuel, etc.)(4): …
3.2.11.5.L1e — L7eLubricating pump: yes/no(4) …
3.2.11.6.L1e — L7eOil cooler: yes/no(4)
3.2.11.6.1.L1e — L7eDrawing …
3.2.11.7.L1e — L7eLubricant(s) characteristics: …
3.2.11.8.L1e — L7eLubricant mixed with the fuel: yes/no(4): …
3.2.11.8.1.L1e — L7ePercentage range of lubricant mixed with the fuel: …
3.2.12. Exhaust system and control
3.2.12.1.L1e — L7eBrief description and schematic drawing of exhaust devices for noise and tailpipe emission control: …
3.2.12.2.L1e — L7eDescription and drawing of the exhaust manifold: …
3.2.12.3.L1e — L7eDescription and detailed drawing of the exhaust device: …
3.2.12.4.L1e — L7eMaximum permissible exhaust back-pressure at rated engine speed and at 100 % load: … kPa(29)
3.2.12.5.L1e — L7eType, marking of exhaust noise-abatement device(s): …
* 3.2.12.6.L1e — L7eNoise-reducing measures in the engine compartment and on the engine where relevant for external noise: …
3.2.12.7.L1e — L7eLocation of the exhaust outlet: …
3.2.12.8.L1e — L7eExhaust noise-abatement device containing fibrous materials: yes/no(4): …
3.2.13. Other electrical systems and control than those intended for the electrical propulsion
3.2.13.1.L1e — L7eRated voltage: … V, positive/negative ground(4)
3.2.13.2.L1e — L7eGenerator: yes/no(4):
3.2.13.2.1.L1e — L7eNominal output: … VA
3.2.13.3.L1e — L7eBattery(ies): yes/no(4)
3.2.13.3.1.L1e — L7eCapacity and other characteristics (mass,…): …
3.2.13.4.L1e — L7eElectric heating systems for the passenger compartment: yes/no(4)
3.3. Pure electric and hybrid electric propulsion and control
3.3.1.L1e — L7eElectric vehicle configuration: pure electric/hybrid electric/manpower — electric(4):
3.3.2.L1e — L7eBrief description and schematic drawing of pure and hybrid electric propulsions and its control system(s): …
3.3.3. Electric propulsion motor
3.3.3.1.L1e — L7eNumber of electric motors for propulsion: …
3.3.3.2.L1e — L7eType (winding, excitation): …
3.3.3.3.L1e — L7eOperating voltage: … V
F13.3.3.4. L1e — L7e 15/30 (4) minutes power (27) : … kW
3.3.4. Propulsion batteries
3.3.4.1.L1e — L7ePrimary propulsion battery
3.3.4.1.1.L1e — L7eNumber of cells: …
3.3.4.1.2.L1e — L7eMass: … kg
3.3.4.1.3.L1e — L7eCapacity: … Ah (Amp-hours) / … V
3.3.4.1.4.L1e — L7eVoltage: … V
3.3.4.1.5.L1e — L7ePosition in the vehicle: …
3.3.4.2.L1e — L7eSecondary propulsion battery
3.3.4.2.1.L1e — L7eNumber of cells: …
3.3.4.2.2.L1e — L7eMass: … kg
3.3.4.2.3.L1e — L7eCapacity: … Ah (Amp-hours) / … V
3.3.4.2.4.L1e — L7eVoltage: … V
3.3.4.2.5.L1e — L7ePosition in the vehicle: …
3.3.5. Hybrid electric vehicle
3.3.5.1.L1e — L7eEngine or motor combination (number of electric motor(s) and/or combustion engine(s)/other)(4): …
3.3.5.2.L1e — L7eCategory of hybrid electric vehicle: off-vehicle charging/not off-vehicle charging:
3.3.5.3.L1e — L7eOperating mode switch: with/without(4)
3.3.5.4.L1e — L7eSelectable modes: yes/no(4)
3.3.5.5.L1e — L7ePure fuel consuming: yes/no(4)
3.3.5.6.L1e — L7eVehicle propelled with fuel cell: yes/no(4)
3.3.5.7.L1e — L7eHybrid operation modes: yes/no(4) (if yes, short description): …
3.3.6. Energy storage device
3.3.6.1.L1e — L7eDescription: (battery, capacitor, flywheel/generator)(4)
3.3.6.2.L1e — L7eIdentification number: …
* 3.3.6.3.L1e — L7eKind of electrochemical couple: …
3.3.6.4.L1e — L7eEnergy (for battery: voltage and capacity Ah in 2h, for capacitor: J,…, for flywheel/generator: J,…,): …
3.3.6.5.L1e — L7eCharger: on-board/external/without(4)
3.3.7. Electric motor (describe each type of electric motor separately) …
3.3.7.1.L1e — L7ePrimary use: propulsion motor/generator(4)
3.3.7.2.L1e — L7eWhen used as propulsion motor: single-/multi-motors (number)(4): …
3.3.7.3.L1e — L7eWorking principle: …
3.3.7.4.L1e — L7eDirect current/alternating current/number of phases: …
3.3.7.5.L1e — L7eSeparate excitation/series/compound(4):
3.3.7.6.L1e — L7eSynchronous/asynchronous(4):
3.3.8. Electric motor control unit
3.3.8.1.L1e — L7eIdentification number: …
3.3.9. Power controller
3.3.9.1.L1e — L7eIdentification number: …
3.4. Other engines, electric motors or combinations (specific information concerning the parts of these motors)
3.4.1. Cooling system (temperatures permitted by the manufacturer)
3.4.1.1.L1e — L7eLiquid cooling: …
3.4.1.1.1.L1e — L7eMaximum temperature at outlet: … K
3.4.1.2.L1e — L7eAir cooling: …
3.4.1.2.1.L1e — L7eReference point: …
3.4.1.2.2.L1e — L7eMaximum temperature at reference point: … K
3.4.2. Lubrication system
3.4.2.1.L1e — L7eDescription of lubrication system: …
3.4.2.2.L1e — L7eLocation of oil reservoir (if any): …
3.4.2.3.L1e — L7eFeed system (pump/injection into induction system/mixed with the fuel, etc.)(4): …
3.4.2.4.L1e — L7eLubricant mixed with the fuel: …
3.4.2.4.1.L1e — L7ePercentage: …
3.4.2.5.L1e — L7eOil cooler: yes/no(4): …
* 3.4.2.5.1.L1e — L7eDrawing(s): …
3.5. Drive-train and control (13)
3.5.1.L1e — L7eBrief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train): …
3.5.2. Clutch
3.5.2.1.L1e — L7eBrief description and schematic drawing of the clutch and its control system: …
3.5.3. Transmission
3.5.3.1.L1e — L7eBrief description and schematic drawing of gear shift system(s) and its control: …
3.5.3.2.L1e — L7eDrawing of the transmission: …
3.5.3.3.L1e — L7eType (mechanical, hydraulic, electric, manual/manual automated/automatic/CVT/ other (indicate).)(4): …
3.5.3.4.L1e — L7eA brief description of the electrical/electronic components (if any): …
3.5.3.5.L1e — L7eLocation relative to the engine: …
3.5.3.6.L1e — L7eMethod of control: …
F23.5.4. L1e — L7e Gear ratios

Overview gear ratios

Gear (24) Internal transmission ratios (ratios of engine to transmission output shaft revolutions) Final drive ratio(s) (ratio of transmission output shaft to driven wheel revolutions) Total gear ratios Ratio (engine speed/vehicle speed) for manual transmission only

1

2

3

…

Reverse
3.5.4.1.

L3e-AxE,

L3e-AxT

Final drive ratio: …
3.5.4.2.

L3e-AxE,

L3e-AxT

Overall gear ratio in highest gear: …
3.6. Safe-cornering device
3.6.1.L1e — L7e equipped with twinned wheels, L2e, L5e, L6e, L7eSafe-cornering device (Annex VIII to Regulation (EU) No 168/2013: yes/no(4); differential/other(4)
3.6.2.L1e — L7e equipped with twinned wheels, L2e, L5e, L6e, L7eDifferential lock: yes/no/optional(4)
3.6.3.L1e — L7eBrief description and schematic drawing of the safe-cornering device, the differential lock and their control systems: …
3.7. Suspension and control
3.7.1.L1e — L7eBrief description and schematic drawing of suspension and its control system: …
3.7.2.L1e — L7eDrawing of the suspension arrangements: …
3.7.3.L1e — L7eLevel adjustment: yes/no/optional(4)
3.7.4.L1e — L7eBrief description of the electrical/electronic components: …
3.7.5.L1e — L7eStabilisers: yes/no/optional(4)
3.7.6.L1e — L7eShock absorbers: yes/no/optional(4)
3.8. Passenger-compartment heating system and air-conditioning
3.8.1. Passenger-compartment heating system
3.8.1.1.L2e, L5e-B, L6e-B, L7eAn overall drawing of the heating system giving its location on the vehicle (and the arrangement of the sound damping devices (including the position of the heat exchange points)): …
3.8.1.2.L2e, L5e-B, L6e-B, L7eAn overall drawing of the heat-exchanger used in systems utilising the heat from the exhaust gases, or of the parts where that exchange takes place (in the case of heating systems using the heat provided by the engine cooling air): …
3.8.1.3.L2e, L5e-B, L6e-B, L7eA sectional drawing of the heat-exchanger or parts where heat exchange takes place, together with a statement of the wall thickness, of the materials used and the characteristics of their surface: …
3.8.1.4.L2e, L5e-B, L6e-B, L7eSpecifications regarding the method of manufacture and technical data relating to other major components of the heating system, such as the fan: …
3.8.2. Air-conditioning
3.8.2.1.L2e, L5e-B, L6e-B, L7eBrief description and schematic drawing of air-conditioning and its control system: …
3.8.2.2.L2e, L5e-B, L6e-B, L7eGas used as refrigerant in the air-conditioning system: …
3.8.2.3.L2e, L5e-B, L6e-B, L7eThe air-conditioning system is designed to contain fluorinated greenhouse gases with global warming potential higher than 150: yes/no(4). If Yes, fill in the following sections:
3.8.2.3.1.L2e, L5e-B, L6e-B, L7eDrawing and brief description of the air-conditioning system, including the reference or part number and material of the leak components: …
3.8.2.3.2.L2e, L5e-B, L6e-B, L7eLeakage of the air-conditioning system
3.8.2.3.3.L2e, L5e-B, L6e-B, L7eReference or part number and material of the components of the system and test information (e.g. test report number, Type-approval number, etc.): …
3.8.2.3.4.L2e, L5e-B, L6e-B, L7eOverall leakage/year of the entire system: … g/year
3.9. Cycles designed to pedal
3.9.1.L1eRatio manpower/electric power: …
3.9.2.L1eMaximum assistance factor: …
3.9.3.L1eMaximum vehicle speed for which the electric motor gives assistance: … km/h
3.9.4.L1eSwitch-off distance: … km
4. GENERAL INFORMATION ON ENVIRONMENTAL AND PROPULSION PERFORMANCE
4.0 General information on environmental and propulsion performance
F34.0.1. L1e — L7e Environmental step: Euro (3/4/5/5+) (4)
4.0.2. L1e — L7e Fuel consumption (provide details for each reference fuel tested) … l/kg (4) /100 km
4.0.3. L1e — L7e CO 2 emissions (25) : … g/km
4.0.4. L1e — L7e Energy consumption (25) : … Wh/km
4.0.5. L1e — L7e Electric range (25) : … km
4.1. Tailpipe emission-control system
4.1.1.L1e — L7eBrief description and schematic drawing of the tailpipe emission-control system and its control: …
4.1.2. Catalytic converter
4.1.2.1.L1e — L7eConfiguration, number of catalytic converters and elements (information to be provided for each separate unit): …
4.1.2.2.L1e — L7eDrawing with dimensions, shape and volume of the catalytic converter(s): …
4.1.2.3.L1e — L7eCatalytic reaction: …
* 4.1.2.4.L1e — L7eTotal charge of precious metals: …
* 4.1.2.5.L1e — L7eRelative concentration: …
* 4.1.2.6.L1e — L7eSubstrate (structure and material): …
* 4.1.2.7.L1e — L7eCell density: …
* 4.1.2.8.L1e — L7eCasing for the catalytic converter(s): …
4.1.2.9.L1e — L7eLocation of the catalytic converter(s) (place and reference distance in the exhaust line): …
4.1.2.10.L1e — L7eCatalyst heat-shield: yes/no(4)
4.1.2.11.L1e — L7eBrief description and schematic drawing of the regeneration system/method of exhaust after-treatment systems and its control system: …
* 4.1.2.11.1.L1e — L7eNormal operating temperature range: … K
4.1.2.11.2.L1e — L7eConsumable reagents: yes/no(4)
4.1.2.11.3.L1e — L7eBrief description and schematic drawing of the reagent flow (wet) system and its control system: …
4.1.2.11.4.L1e — L7eType and concentration of reagent needed for catalytic action: …
* 4.1.2.11.5.L1e — L7eNormal operational temperature range of reagent: … K
4.1.2.11.6.L1e — L7eFrequency of reagent refill: continuous/maintenance(4)
4.1.2.12.L1e — L7eIdentifying part number: …
4.1.3. Oxygen sensor(s)
4.1.3.1.L1e — L7eOxygen sensor component(s) drawing(s): …
4.1.3.2.L1e — L7eDrawing of exhaust device with oxygen sensor location(s) (dimensions relative to exhaust valves): …
4.1.3.3.L1e — L7eControl range(s): …
4.1.3.4.L1e — L7eIdentifying part number(s): …
4.1.3.5.L1e — L7eDescription of oxygen sensor heating system and heating strategy: …
4.1.3.6.L1e — L7eOxygen sensor heat shield(s): yes/no(4)
4.1.4. Secondary air-injection (air-inject in exhaust)
4.1.4.1.L1e — L7eBrief description and schematic drawing of the secondary air-injection system and its control system: …
4.1.4.2.L1e — L7eConfiguration (mechanical, pulse air, air pump etc.)(4): …
4.1.4.3.L1e — L7eWorking principle: …
4.1.5. External exhaust gas recirculation (EGR)
4.1.5.1.L1e — L7eBrief description and schematic drawing of the EGR system (exhaust flow) and its control system: …
4.1.5.2.L1e — L7eCharacteristics: …
4.1.5.3.L1e — L7eWater-cooled EGR system: yes/no(4)
4.1.5.4.L1e — L7eAir-cooled EGR system: yes/no(4)
4.1.6. Particulate filter
4.1.6.1.L1e — L7ePT component drawing with dimensions, shape and capacity of the particulate filter: …
4.1.6.2.L1e — L7eDesign of the particulate filter: …
4.1.6.3.L1e — L7eBrief description and schematic drawing of the particulate filter and its control system: …
4.1.6.4.L1e — L7eLocation (reference distance in the exhaust line): …
4.1.6.5.L1e — L7eMethod or system of regeneration, description and drawing: …
4.1.6.6.L1e — L7eIdentifying part number: …
4.1.7. Lean NOx trap
4.1.7.1.L1e — L7eOperation principle of lean NOx trap: …
4.1.8. Additional tailpipe emission-control devices (if any not covered under another heading)
4.1.8.1.L1e — L7eWorking principle: …
4.2. Crankcase emission control system
4.2.1.L1e — L7eConfiguration of crank-case gas recycling system (breather system, positive crank-case ventilation system, other)(4) (description and drawings).
4.3. Evaporative emission control system
4.3.1.L1e — L7eEvaporative emissions control system: yes/no(4)
4.3.2.L1e — L7eDrawing of the evaporative control system
4.3.3.L1e — L7eDrawing of the canister (including dimensions and indicating vent and purge mechanism)
4.3.4.L1e — L7eWorking capacity: … g
4.3.5.L1e — L7eAdsorption material: … (e.g. charcoal, carbon, synthetic, …)
4.3.6.L1e — L7eHousing material: … (e.g. plastic, steel, …)
4.3.7.L1e — L7eSchematic drawing of the fuel tank, indicating capacity and material: …
4.3.8.L1e — L7eDrawing of the heat-shield between tank and exhaust device: …
4.4. Additional information on environmental and propulsion unit performance
4.4.1.L1e — L7eDescription and/or schematic drawings of additional pollution-control devices: …
4.4.2.L1e — L7eLocation of the coefficient of absorption symbol (compression-ignition engines only): …
4.4.3.L1e — L7eApplicable information document set out in respectively UN Regulation No 9, 41 or 63 shall supplement this information document with regard to the sound level.
4.4.4.L1e — L7eApplicable information document set out in respectively UN Regulation No 92 shall supplement this information document with regards to the noise-abatement devices installed on the vehicle.
5. VEHICLE PROPULSION FAMILY
5.1.L1e — L7eTo define the vehicle propulsion family, the manufacturer shall submit the information required for classification criteria set out in point 3 of Annex XI to Commission Delegated Regulation (EU) No 134/2014, if not already provided in the information document.
6. INFORMATION ON FUNCTIONAL SAFETY
6.1. Audible warning devices
6.1.1.L1e — L7eSummary description of device(s) used and their purpose: …
6.1.2.L1e — L7eDrawing(s) showing the location of the audible warning device(s) in relation to the structure of the vehicle: …
6.1.3.L1e — L7eDetails of the method of attachment, including the part of the vehicle structure to which the audible warning device(s) is (are) attached: …
6.1.4.L1e — L7eElectrical/pneumatic circuit diagram: …
6.1.4.1.L1e — L7eVoltage: AC/DC(4)
6.1.4.2.L1e — L7eRated voltage or pressure: …
6.1.5.L1e — L7eDrawing of the mounting device: …
6.2. Braking, including anti-lock and combined braking systems
6.2.1.L1e — L7eCharacteristics of the brakes, including details and drawings of the drums, discs, hoses, make and type of shoe/pad assemblies and/or linings, effective braking areas, radius of drums, shoes or discs, mass of drums, adjustment devices, relevant parts of the axle(s) and suspension, levers, pedals (4): …
6.2.2.L1e — L7eOperating diagram, description and/or drawing of the braking system, including details and drawings of the transmission and controls as well as a brief description of the electrical and/or electronic components used in the braking system(4):
6.2.2.1.L1e — L7eFront, rear and sidecar brakes, disc and/or drum(4):
6.2.2.2.L1e — L7eParking braking system: …
6.2.2.3.L1e — L7eAny additional braking system: …
6.2.3.L1e — L7eVehicle is equipped to tow a trailer with no brake/overrun brake/electric/pneumatic/hydraulic service brakes: yes/no(4): …
6.2.4.L1e — L7eAnti-lock/Combined braking system
6.2.4.1.L1e — L7eAnti-lock braking system: yes/no/optional(4)
6.2.4.2.L1e — L7eCombined braking system: yes/no/optional(4)
6.2.4.3.L1e — L7eAnti-lock and combined braking system: yes/no/optional(4)
6.2.4.4.L1e — L7eSchematic drawing(s): …
6.2.5.L1e — L7eHydraulic reservoir(s) (volume and location): …
6.2.6.L1e — L7eParticular characteristics of the braking system(s)
6.2.6.1.L1e — L7eBrake shoes and/or pads(4): …
6.2.6.2.L1e — L7eLinings and/or pads (indicate make, type, grade of material or identification mark): …
6.2.6.3.L1e — L7eBrake levers and/or pedals(4): …
6.2.6.4.L1e — L7eOther devices (where applicable): drawing and description: …
6.3. Electrical safety
6.3.1.L1e — L7eBrief description of the power circuit components installation and drawings/photographs showing the location of the power circuit components installation: …
6.3.2.L1e — L7eSchematic diagram of all electrical functions included in power circuit: …
6.3.3.L1e — L7eWorking voltage(s) (V): …
6.3.4.L1e — L7eDescription of protection against electric-shocks: …
6.3.5.L1e — L7eFuse and/or circuit breaker yes/no/optional(4)
6.3.5.1.L1e — L7eDiagram showing the functional range: …
6.3.6.L1e — L7eConfiguration of power wiring harness: …
6.4. Front and rear protective structures
6.4.1. Front protective structure
6.4.1.1.L1e — L7eDetailed technical description (including photographs or drawings): …
6.4.1.2.L1e — L7eMaterials used: …
6.4.2. Rear protective structure
6.4.2.1.L1e — L7eDetailed technical description (including photographs or drawings): …
6.4.2.2.L1e — L7eMaterials used: …
6.5. Glazing, windscreen wipers and washers, and defrosting and demisting systems
6.5.1. Windscreen
6.5.1.1.L2e, L5e, L6e, L7eMaterials used: …
6.5.1.2.L2e, L5e, L6e, L7eMethod of mounting: …
6.5.1.3.L2e, L5e, L6e, L7eAngle of inclination: …
6.5.1.4.L2e, L5e, L6e, L7eWindscreen accessories and the position in which they are fitted, together with a brief description of any electrical/electronic components: …
6.5.1.5.L2e, L5e, L6e, L7eDrawing of the windscreen with dimensions: …
6.5.2. Other windows
6.5.2.1.L2e, L5e, L6e, L7eMaterials used: …
6.5.2.2L2e, L5e, L6e, L7eA brief description of the electrical/electronic components (if any) of the window lifting mechanism: …
6.5.3. Opening roof glazing
6.5.3.1.L2e, L5e, L6e, L7eMaterials used: …
6.5.4. Other glass panes
6.5.4.1.L2e, L5e, L6e, L7eMaterials used: …
6.6. Windscreen wiper(s)
6.6.1.L2e, L5e, L6e, L7eDetailed technical description (including photographs or drawings): …
6.7. Windscreen washer
6.7.1.L2e, L5e, L6e, L7eDetailed technical description (including photographs or drawings): …
6.7.2.L2e, L5e, L6e, L7eCapacity of the reservoir: … l
6.8. Defrosting and demisting
6.8.1.L2e, L5e, L6e, L7eDetailed technical description (including photographs or drawings): …
6.9. Driver-operated controls including identification of controls, tell-tales and indicators
6.9.1.L1e — L7eArrangement and identification of controls, tell-tales and indicators: …
6.9.2.L1e — L7ePhotographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators: …
6.9.3.L1e — L7eControls, tell-tales and indicators for which, when fitted, identification is mandatory, including the identification symbols to be used for that purpose:
6.9.4.L1e — L7e

Summary table: the vehicle is equipped with the following driver-operated controls, including indicators and tell-tales(4)

Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purpose

  1. (+)
    x

  2. yes

    3. -

  3. no or not separately available

    4. o

  4. optional.

  1. (++)
    d

  2. directly on control, indicator or tell-tale

    3. c

  3. in close vicinity.
Symbol NoDeviceControl / indicator availablef4 Identified by symbol Wheref5 Tell-tale available Identified by symbol Where
1Master light
2Dipped-beam head lamps
3Main-beam head lamps
4Position (side) lamps
5Front fog lamps
6Rear fog lamp
7Headlamp levelling device
8Parking lamps
9Direction indicators
10Hazard warning
11Windscreen wiper
12Windscreen washer
13Windscreen wiper and washer
14Headlamp cleaning device
15Windscreen demisting and defrosting
16Rear window demisting and defrosting
17Ventilating fan
18Diesel pre-heat
19Choke
20Brake failure
21Fuel level
22Battery charging condition
23Engine coolant temperature
24Malfunction indicator light (MI)
6.9.5.L1e — L7e

Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which shall be used if they are to be identified

  1. (+)
    x

  2. yes

    3. -

  3. no or not separately available

    4. o

  4. optional.

  1. (++)
    d

  2. directly on control, indicator or tell-tale

    3. c

  3. in close vicinity.
Symbol NoDeviceControl / indicator availablef6 Identified by symbol Wheref7 Tell-tale available Identified by symbol Where
1Parking brake
2Rear window wiper
3Rear window washer
4Rear window wiper and washer
5Intermittent windscreen wiper
6Audible warning device (horn)
7Front hood (bonnet)
8Rear hood (boot)
9Seat belt
10Engine oil pressure
11Unleaded petrol
12…
13…
6.10. Speedometer and odometer
6.10.1. Speedometer
6.10.1.1.L1e — L7ePhotographs and/or drawings of the complete system: …
6.10.1.2.L1e — L7eVehicle speed range displayed: …
6.10.1.3.L1e — L7eTolerance of the measuring mechanism of the speedometer: …
6.10.1.4.L1e — L7eTechnical constant of the speedometer: …
6.10.1.5.L1e — L7eMethod of operation and description of the drive mechanism: …
6.10.1.6.L1e — L7eOverall transmission ratio of the drive mechanism: …
6.10.2. Odometer
6.10.2.1.L1e — L7eTolerance of the measuring mechanism of the odometer: …
6.10.2.2.L1e — L7eMethod of operation and description of the drive mechanism: …
6.11. Installation of lighting, light-signalling devices, including automatic switching of lighting
6.11.1.L1e — L7eList of all devices (mentioning the number, make(s),type, component type-approval mark(s), the maximum intensity of the main-beam headlamps, colour, the corresponding tell-tale): …
6.11.2.L1e — L7eDiagram showing the location of the lighting and light-signalling devices: …
6.11.3.L1e — L7eHazard warning lamps: …
6.11.4.L1e — L7eBrief description of the electrical and/or electronic components used in the lighting system and in the light-signalling system: …
6.11.5.L1e — L7eFor every lamp and reflector, supply the following information (in writing and/or by diagram):
6.11.5.1.L1e — L7eDrawing showing the extent of the illuminating surface: …
6.11.5.2.L1e — L7eMethod used to define the apparent surface in accordance with point 2.10 of UNECE Regulation No 48 (OJ L 323, 6.12.2011, p. 46): …
6.11.5.3.L1e — L7eAxis of reference and centre of reference: …
6.11.5.4.L1e — L7eMethod of operation of concealable lamps: …
6.11.6.L1e — L7eDescription/drawing and type of headlamp levelling device (e.g. automatic, stepwise manually adjustable, continuously manually adjustable)(4): …
6.11.6.1.L1e — L7eControl device: …
6.11.6.2.L1e — L7eReference marks: …
6.11.6.3.L1e — L7eMarks assigned for loading conditions: …
6.12. Rearward visibility
6.12.1. Rear-view mirrors (stating for each mirror)
6.12.1.1.L1e — L7eDrawing(s) for the identification of the mirror showing the position of the mirror relative to the vehicle structure: …
6.12.1.2.L1e — L7eDetails of the method of attachment including that part of the vehicle structure to which it is attached: …
6.12.1.3.L1e — L7eA brief description of the electronic components of the adjustment system: …
6.12.2.L1e — L7e Devices for indirect vision other than mirrors
6.12.2.1.L1e — L7eDescription of the device: …
6.12.2.2.L1e — L7eIn the case of a camera-monitor device, the detection distance (mm), contrast, luminance range, glare correction, display performance (black and white/colour(4)), image repetition frequency, luminance reach of the monitor(4): …
6.12.2.3.L1e — L7eSufficiently detailed drawings to identify the complete device, including installation instructions; the position for the EU type-approval mark has to be indicated on the drawings: …
6.13. Rollover protective structure (ROPS)
6.13.1.L7e-B2Detailed technical description, position, fixing, etc. (including photographs or drawings): …
6.13.2. ROPS by Frame(4)
6.13.2.1.L7e-B2Internal and external dimensions: …
6.13.2.2.L7e-B2Material(s) and method of construction: …
6.13.3. ROPS by Cab (4)
6.13.3.1.L7e-B2Other weather protection arrangements (description): …
6.13.3.2.L7e-B2Internal and external dimensions: …
6.13.4. ROPS by Roll bar(s) mounted at front/rear(4), fold-down/not fold down (4)
6.13.4.1.L7e-B2Dimensions: …
6.13.4.2.L7e-B2Material(s) and method of construction: …
6.14. Safety belts and/or other restraints
6.14.1.L2e, L4e, L5e-B, L6e-B, L7e

Number and position of safety belts and restraint systems and seats on which they can be used, please fill out table below:

(L = left side, R = right side, C = centre)

Safety belt configuration and associated information

L = left, C= centre, R=right
Complete EU type-approval markVariant, if applicableBelt adjustment device for height (indicate yes/no/optional)
First row of seatsL
C
R
Second row of seatsL
C
R
6.14.2.L2e, L4e, L5e-B, L6e-B, L7eDescription of a specific type of belt, with one anchorage attached to the seat back-rest or incorporating an energy-dissipation device: …
6.14.3.L2e, L4e, L5e-B, L6e-B, L7eNumber and location of the anchorages: …
6.14.4.L2e, L4e, L5e-B, L6e-B, L7eBrief description of electrical/electronic components: …
6.15. Safety belt anchorages
6.15.1.L2e, L4e, L5e-B, L6e-B, L7ePhotographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point: …
6.15.2.L2e, L4e, L5e-B, L6e-B, L7eDrawings of the anchorages and the parts of the vehicle structure to which they are attached (together with a statement on the nature of the materials used): …
6.15.3.L2e, L4e, L5e-B, L6e-B, L7eDesignation of the types of belts(14) authorised for attachment to the anchorages on the vehicle: …

Safety-belt anchorage configuration and associated information

Anchorage location
Vehicle structureSeat structure
First row of seats
Right-hand seat

Lower anchorages

Upper anchorages

outboard inboard
Centre seat

Lower anchorages

Upper anchorages

right left
Left-hand seat

Lower anchorages

Upper anchorages

outboard inboard
Second row of seats
Right-hand seat

Lower anchorages

Upper anchorages

outboard inboard
Centre seat

Lower anchorages

Upper anchorages

right left
Left-hand seat

Lower anchorages

Upper anchorages

outboard inboard
6.15.4.L2e, L4e, L5e-B, L6e-B, L7eType-approval mark for each position: …
6.15.5.L2e, L4e, L5e-B, L6e-B, L7eSpecial devices (example: seat-height adjustment, preloading device, etc.): …
6.15.6.L2e, L4e, L5e-B, L6e-B, L7ePhotographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point: …
6.15.7.L2e, L4e, L5e-B, L6e-B, L7eObservation: …
6.16. Seating positions (saddles and seats)
6.16.1.L1e — L7eNumber of seating positions: …
6.16.1.1.L2e, L5e, L6e, L7eLocation and arrangement(8): …
6.16.2.L1e — L7eSeating position configuration: seat/saddle(4)
6.16.3.L1e — L7eDescription and drawings of:
6.16.3.1.L1e — L7eThe seats and their anchorages: …
6.16.3.2.L1e — L7eThe adjustment system: …
6.16.3.3.L1e — L7eThe displacement and locking systems: …
6.16.3.4.L1e — L7eThe seat-belt anchorages incorporated in the seat structure: …
6.16.3.5.L1e — L7eThe parts of the vehicle used as anchorages: …
6.16.4.L2e, L4e, L5e-B, L6e-B, L7eCoordinates or drawing of the R-point(s) of all seating positions: …
6.16.4.1.L2e, L4e, L5e-B, L6e-B, L7eDriver’s seat: …
6.16.4.2.L2e, L4e, L5e-B, L6e-B, L7eAll other seating positions: …
6.16.5.L1e — L7eDesign torso angle: …
6.16.5.1.L1e — L7eDriver’s seat: …
6.16.5.2.L1e — L7eAll other seating positions: …
6.16.6.L1e — L7eRange of seat adjustment: …
6.16.6.1.L1e — L7eDriver’s seat: …
6.16.6.2.L1e — L7eAll other seating positions: …
6.17. Steer-ability, cornering properties and turn-ability
6.17.1.L1e — L7eSchematic diagram of steered axle(s) showing steering geometry: …
6.17.2. Transmission and control of steering
6.17.2.1.L1e — L7eConfiguration of steering transmission (specify for front and rear): …
6.17.2.2.L1e — L7eLinkage to wheels (including other than mechanical means; specify for front and rear): …
6.17.2.2.1.L1e — L7eA brief description of the electrical/electronic components: …
6.17.2.3.L1e — L7eDiagram of the steering transmission: …
6.17.2.4.L2e, L5e, L6e, L7eSchematic diagram(s) of the steering control(s): …
6.17.2.5.L2e, L5e, L6e, L7eRange and method of adjustment of the steering control(s): …
6.17.2.6.L2e, L5e, L6e, L7eMethod of assistance: …
6.17.3. Maximum steering angle of the wheels
6.17.3.1.L1e — L7eTo the right: … degrees; number of turns of the steering wheel (or equivalent data): …
6.17.3.2.L1e — L7eTo the left: … degrees; number of turns of the steering wheel (or equivalent data): …
6.18. Tyres/wheels combination
6.18.1. Tyres:
6.18.1.1.Size designation
6.18.1.1.1.L1e — L7eAxle 1: …
6.18.1.1.2.L1e — L7eAxle 2: …
6.18.1.1.3.L4eSidecar wheel: …
6.18.1.2.L1e — L7eMinimum load-capacity index: … with the maximum load on each tyre: … kg
6.18.1.3.L1e — L7eMinimum-speed category symbol compatible with the theoretical maximum design vehicle speed: …
6.18.1.4.L1e — L7eTyre pressure(s) as recommended by the vehicle manufacturer: … kPa
6.18.2. Wheels:
6.18.2.1.L1e — L7eRim size(s): …
6.18.2.2.L1e — L7eCategories of use compatible with the vehicle: …
6.18.2.3.L1e — L7eNominal rolling circumference: …
6.19. Vehicle maximum speed limitation plate and its location on the vehicle
6.19.1.L7e-B1 and L7e-B2Maximum speed limitation plate (indicate the reflecting material used; drawings and photos may be used as appropriate): …
6.19.2.L7e-B1 and L7e-B2Location of maximum speed limitation plate (indicate variants where necessary; drawings and photos may be used as appropriate): …
6.19.3.L7e-B1 and L7e-B2Height above road surface, upper edge: … mm
6.19.4.L7e-B1 and L7e-B2Height above road surface, lower edge: … mm
6.19.5.L7e-B1 and L7e-B2Distance of the centre line from the longitudinal median plane of the vehicle: … mm
6.19.6.L7e-B1 and L7e-B2Distance from the left vehicle edge: … mm
6.20. Vehicle occupant protection, including interior fittings and vehicle doors
6.20.1. Bodywork
6.20.1.1.L2e, L5e-B, L6e-B, L7eMaterials used and methods of construction: …
6.20.2. Occupant doors, latches and hinges
6.20.2.1.L2e, L5e, L6e, L7eNumber of doors, and its configuration, dimensions and maximum angle of opening(5): …
6.20.2.2.L2e, L5e, L6e, L7eDrawing of latches and hinges and of their position in the doors: …
6.20.2.3.L2e, L5e, L6e, L7eTechnical description of latches and hinges: …
6.20.2.4.L2e, L5e, L6e, L7eDetails, including dimensions, of entrances, steps and necessary handles where applicable: …
6.20.3. Interior protection for occupants
6.20.3.1.L2e, L5e, L6e, L7ePhotographs, drawings and/or an exploded view of the interior fittings, showing the parts in the passenger compartment and the materials used (with the exception of interior rear view mirrors, arrangement of controls, seats and the rear part of seats), roof and opening roof, backrest: …
6.20.4. Head restraints
6.20.4.1.L2e, L5e, L6e, L7eHead restraints: integrated/detachable/separate(4)
6.20.4.2.L2e, L5e, L6e, L7eDetailed description of the head restraint, specifying in particular the nature of the padding material or materials and, where applicable, the position and specifications of the braces and anchorage pieces for the type of seat for which approval is sought: …
6.20.4.3.L2e, L5e, L6e, L7eIn the case of a ‘separate’ head restraint
6.20.4.3.1.L2e, L5e, L6e, L7eDetailed description of the structural zone to which the head restraint is intended to be fixed: …
6.20.4.3.2.L2e, L5e, L6e, L7eScale drawings of the significant parts of the structure and the head restraint: …
6.21. Maximum continuous total power and/or maximum vehicle speed limitation by design
6.21.1. Propulsion and/or drive-train output governors
6.21.1.1.L1e — L7eNumber (minimum two, exemption L3e-A3 and L4e-A3):
6.21.1.2.L1e — L7eHow is the redundancy of governors ensured?: …
6.21.1.3.L1e — L7eNominal cut-off point no 1: …
6.21.1.3.1.L1e — L7eEngine/motor/drive-train rotation speed at which cut-off starts under load: … min-1
6.21.1.3.2.L1e — L7eMaximum rotation speed at the minimum engine load: … min-1
6.21.1.4.L1e — L7eNominal cut-off point no 2: …
6.21.1.4.1L1e — L7eEngine/motor/drive-train rotation speed at which cut-off starts under load(4): … min-1
6.21.1.4.2.L1e — L7eMaximum rotation speed at the minimum engine load: … min-1
6.21.1.5.L1e — L7eThe stated purpose of governor(s): maximum design vehicle speed limitation/maximum power limitation/engine over-speed protection(4): …
7. INFORMATION ON VEHICLE CONSTRUCTION
7.1. Coupling devices and attachments
7.1.1.L1e — L7eL-category vehicle equipped with coupling device: yes/no/optional(4)
7.1.2.L1e — L7eGuidelines and information for consumers in all EU languages regarding the impact on the driveability of using a trailer with an L-category vehicle included in the owner's manual: yes/no(4)
7.1.3.L1e — L7eFor coupling-device approved as separate technical unit: installation and operating instructions added to documentation: yes/no(4)
7.1.4.L1e — L7ePhotographs and/or drawings showing the position and the construction of the coupling-devices: …
7.1.5.L1e — L7eInstructions for attaching the coupling-type to the vehicle and photographs or drawings of the fixing points on the vehicle as stated by the manufacturer; additional information, if the use of the coupling-type is restricted to certain variants or versions of the vehicle type: …
7.1.6.L1e — L7eAttachment points for a secondary coupling and/or breakaway cable (drawings and pictures may be used as appropriate): yes/no(4)
7.2. Devices to prevent unauthorised use
7.2.1. Protective device
7.2.1.1.L1e — L7eSummary description of protective device(s) used: …
7.2.2. Vehicle immobiliser
7.2.2.1.L1e — L7eTechnical description of the vehicle immobiliser and of the measures taken against inadvertent activation: …
7.2.3. Alarm system
7.2.3.1.L1e — L7eDescription of the alarm system and of the vehicle parts involved in its installation: …
7.2.3.2.L1e — L7eList of the main components comprising the alarm system: …
7.3. Electromagnetic compatibility (EMC)
7.3.1.L1e — L7eRequirements under UNECE Regulation No 10 (OJ L 254, 20.9.2012, p. 1) are met with relevant documentation included in the information document: yes/no(4)
7.3.2.L1e — L7eTable or drawing of radio-interference control equipment: …
7.3.3.L1e — L7eParticulars of the nominal value of the direct-current resistance, and, in the case of resistive ignition cables, of their nominal resistance per metre: …
7.4. External projections
7.4.1.L1e — L7evehicles with bodyworkGeneral arrangement (drawing or photographs accompanied if necessary by dimensional details and/or text) indicating the position of the attached sections and views, of any parts of the exterior surface which can be regarded as critical for external projections, for example, and where relevant: bumpers, floor line, door and window pillars, air-intake grilles, radiator grille, windscreen wipers, rain gutter channels, handles, slide rails, flaps, door hinges and locks, hooks, eyes, winches, decorative trim, badges, emblems and recesses and any other parts of the exterior surface which can be regarded as critical (e.g. lighting equipment): …
7.5. Fuel storage
7.5.1. Fuel tank(s)
7.5.1.1.Main fuel tank(s)
7.5.1.1.1.L1e — L7eMaximum capacity: …
7.5.1.1.2.L1e — L7eMaterials used: …
7.5.1.1.3.L1e — L7eFuel tank inlet: restricted orifice/label(4) …
7.5.1.2.Reserve fuel tank(s)
7.5.1.2.1.L1e — L7eMaximum capacity: …
7.5.1.2.2.L1e — L7eMaterials used: …
7.5.1.2.3.L1e — L7eFuel tank inlet: restricted orifice/label(4) …
7.5.1.3.L1e — L7eDrawing and technical description of the tank(s) with connections and lines of the breathing and venting system, locks, valves, fastening devices: …
7.5.1.4.L1e — L7eDrawing clearly showing the position of the tank(s) in the vehicle: …
7.5.1.5.L1e — L7eDrawing of the heat shield between tank and exhaust device: …
7.5.2. Compressed natural gas (CNG) container(s)
7.5.2.1.L1e — L7eApplicable information document set out in UNECE regulation No 110f8 as prescribed for vehicle category M1 shall supplement this information document with regards to the CNG tanks installed on the vehicle.
7.5.3.L1e — L7e Liquefied petroleum gas (LPG)container(s)
7.5.3.1.L1e — L7eApplicable information document set out in UNECE regulation No 67f9 as prescribed for vehicle category M1 shall supplement this information document with regards to the LPG tanks installed on the vehicle.
7.6. On-board diagnostics (OBD) functional requirements
7.6.1 On-board diagnostics system
7.6.1.1.L1e — L7eStage I: yes/no(4) and/or
7.6.1.2.L1e — L7eStage II: yes/no(4)
7.6.2. OBD system general information
7.6.2.1.L3e—L7e(10) Written description and/or drawing of the malfunction indicator (MI): …
7.6.2.2.L3e—L7e(10) List and purpose of all components monitored by the OBD system: …
7.6.2.3.L3e— L7e(10) Written description (general working principles) for all OBD stage I circuit (open circuit, shorted low and high, rationality) and electronics (PCU/ECU internal and communication) diagnostics: …
7.6.2.4.L3e—L7e(10) Written description (general working principles) for all OBD stage I diagnostic functionality triggering any operating mode which significantly reduces engine torque in case of fault detection: …
7.6.2.5.L3e— L7e(10) Written description of the communication protocol(s) supported: …
7.6.2.6.L3e—L7e(10) Physical location of diagnostic-connector (add drawings and photographs): …
7.6.2.7.L3e— L7e(10) Written description in case of voluntary compliance with OBD stage II (general working principles):
7.6.2.7.1.L3e — L7e(10) Positive-ignition engines
7.6.2.7.1.1.L3e — L7e(10) Catalyst monitoring: …
7.6.2.7.1.2.L3e — L7e(10) Misfire detection: …
7.6.2.7.1.3.L3e — L7e(10) Oxygen sensor monitoring: …
7.6.2.7.1.4.L3e — L7e(10) Other components monitored by the OBD system: …
7.6.2.7.2.L3e — L7e(10) Compression-ignition engines
7.6.2.7.2.1.L3e — L7e(10) Catalyst monitoring: …
7.6.2.7.2.2.L3e — L7e(10) Particulate filter monitoring: …
7.6.2.7.2.3.L3e — L7e(10) Electronic fuelling system monitoring: …
7.6.2.7.2.4.L3e — L7e(10) deNOx system monitoring: …
7.6.2.7.2.5.L3e — L7e(10) Other components monitored by the OBD system: …
7.6.2.7.3L3e — L7e(10) Criteria for MI activation (fixed number of driving cycles or statistical method): …
7.6.2.7.4.L3e — L7e(10) List of all OBD output codes and formats used (with explanation of each): …
7.6.3.

OBD compatibility

The following additional information shall be provided by the vehicle manufacturer to enable the manufacture of OBD-compatible replacement or service parts, diagnostic tools and test equipment:

7.6.3.1.L3e — L7e(10) A comprehensive document describing all sensed components concerned with the strategy for fault detection and MI activation (fixed number of driving cycles or statistical method). This shall, include a list of relevant secondary sensed parameters for each component monitored by the OBD system. The document shall also list all OBD output codes and formats (with an explanation of each) used in association with individual emission-related powertrain components and individual non-emission-related components, where monitoring the component is used to determine MI activation. This shall contain, in particular, a comprehensive explanation for the data given in service $05 Test ID $ 21 to FF and the data given in service $06: …
7.6.3.2.L3e — L7e(10) For vehicle types using a communication link in accordance with ISO 15765-4 ‘Road vehicles, diagnostics on controller area network (CAN) — Part 4: requirements for emissions-related systems’, the manufacturer shall provide a comprehensive explanation for the data given in service $06 Test ID $00 to FF, for each OBD monitor ID supported: …
7.6.3.3.L3e — L7e(10) The information required above may be provided in table form as described below.

Example OBD fault-code overview list

ComponentFault codeMonitoring strategyFault detection criteriaMI activation criteriaSecondary parametersPreconditioningDemonstration test
Intake air temperature sensor open circuitP0xxxxzzComparison with temperature model after cold start> 20 degr difference between measured and modelled intake air temperature3rd cycleCoolant and intake air temperature sensor signalsTwo type I cyclesType I
7.6.3.4.L3e — L7e(10) Description of ETC diagnostic fault codes: …
F47.6.3.5. L3e — L7e (10) Description of the default modes which a driver may experience in case of an ETC failure
7.6.4.

Communication protocol information

The following information shall be referenced to a specific vehicle make, model and variant, or identified using other workable definitions such as VIN or vehicle and systems identification:

7.6.4.1.L3e — L7e(10) Any protocol information system needed to enable complete diagnostics in addition to the standards prescribed in point 3.8. of Appendix 1 to Annex XII to Commission Delegated Regulation (EU) No 44/2014, such as additional hardware or software protocol information, parameter identification, transfer functions, ‘keep alive’ requirements, or error conditions;
7.6.4.2.L3e — L7e(10) Details of how to obtain and interpret all fault codes not in accordance with the standards prescribed in point 3.11. of Appendix 1 to Annex XII to Commission Delegated Regulation (EU) No 44/2014
7.6.4.3.L3e — L7e(10) A list of all available live data parameters including scaling and access information;
7.6.4.4.L3e — L7e(10) A list of all available functional tests including device activation or control and the means to implement them;
7.6.4.5.L3e — L7e(10) Details of how to obtain all component and status information, time stamps, pending DTC and freeze frames;
7.6.4.6.L3e — L7e(10) PCU/ECU identification and variant coding;
7.6.4.7.L3e — L7e(10) Details of how to reset service lights;
7.6.4.8.L3e — L7e(10) Location of diagnostic connector and connector details;
7.6.4.9.L3e — L7e(10) Engine code identification.
7.6.5. Test and diagnosis of OBD monitored components
7.6.5.1.L3e — L7e(10) A description of tests to confirm its functionality, at the component or in the harness:
7.7. Passenger handholds and footrests
7.7.1. Handholds
7.7.1.1.L1e — L7eConfiguration: strap and/or handle(4)
7.7.1.3.L1e — L7ePhotographs and/or drawings showing the location and the construction:
7.7.2. Footrests
7.7.2.1.L1e — L7ePhotographs and/or drawings showing the location and the construction:
7.8. Registration plate space
7.8.1.L1e — L7eLocation of rear registration plate (indicate variants where necessary; drawings may be used as appropriate): …
7.8.1.1.L1e — L7eHeight above road surface, upper edge: … mm
7.8.1.2.L1e — L7eHeight above road surface, lower edge: … mm
7.8.1.3.L1e — L7eDistance of the centre line from the longitudinal median plane of the vehicle: … mm
7.8.1.4.L1e — L7eDimensions (length x width): … mm x … mm
7.8.1.5.L1e — L7eInclination of the plane to the vertical: … degr.
7.8.1.6.L1e — L7eAngle of visibility in the horizontal plane: … degr
7.9. Stands
7.9.1.L1e, L3eConfiguration: central and/or side(4): …
7.9.2.L1e, L3eConstruction material used: …
7.9.3.L1e, L3ePhotographs and drawings showing the location of the stand(s) in relation to the structure of the vehicle: …
7.9.4.L1e, L3eDescription of the method to prevent contact of the stand with the ground when the vehicle is being propelled: …

Appendix 1

Model information document relating to EU type-approval of a type of/ a type of a vehicle with regard to(4) a tailpipe pollution-control system

Item No(Sub) categoriesDetailed information
B. General information concerning systems, components or separate technical units
0.7.L1e — L7e Make(s) (trade name(s) of manufacturer): …
0.8.L1e — L7e Type: …
0.8.1.L1e — L7eCommercial name(s) (if available): …
0.8.2.L1e — L7eType-approval number(s) (if available): …
0.8.3.L1e — L7eType-approval(s) issued on (date, if available): …
0.9.L1e — L7e Company name and address of manufacturer: …
0.9.1.L1e — L7eName(s) and address(es) of assembly plants: …
0.9.2.L1e — L7eName and address of manufacturer’s authorised representative, if any: …
0.10. Vehicle(s) for which the system/separate technical unit is intended for(21) :
0.10.1.L1e — L7eType(17): …
0.10.2.L1e — L7eVariant(17): …
0.10.3.L1e — L7eVersion(17): …
0.10.4.L1e — L7eCommercial name(s) (if available): …
0.10.5.L1e — L7eCategory, subcategory and sub-subcategory of vehicle(2): …
0.11.L1e — L7e Type-approval marks for components and separate technical units(19) : …
0.11.1.L1e — L7eMethod of attachment: …
0.11.2.L1e — L7ePhotographs and/or drawings of the location of the type-approval mark (completed example with dimensions): …
C. General information concerning vehicle, systems, components or separate technical units
0.12. Conformity of production
0.12.1.L1e — L7eDescription of overall quality-assurance management systems.
1. GENERAL CONSTRUCTION CHARACTERISTICS
1.8. Propulsion unit performance
1.8.1.L3e, L4e, L5e, L7e-A, L7e-B2Declared maximum vehicle speed: … km/h
1.8.2.L1e, L2e, L6e, L7e-B1, L7e-CMaximum design vehicle speed (22): … km/h and gear in which it is reached: …
1.8.3.L1e — L7eMaximum net power combustion engine: … kW at … min–1at A/F ratio: …
1.8.4.L1e — L7eMaximum net torque combustion engine: … Nm at … min–1at A/F ratio: …
1.8.5.L1e — L7eMaximum continuous-rated power electric motor (15/30(4) minutes power(27)): … kW at … min–1
1.8.6.L1e — L7eMaximum continuous-rated torque electric motor: … Nm at … min–1
1.8.7.L1e — L7eMaximum continuous total power for propulsion(s): … kW at … min–1 at A/F ratio: …
1.8.8.L1e — L7eMaximum continuous total torque for propulsion(s): … Nm at … min–1 at A/F ratio: …
1.8.9.L1e — L7eMaximum peak power for propulsion(s): … kW at … min–1at A/F ratio: …
4. GENERAL INFORMATION ON ENVIRONMENTAL AND PROPULSION UNIT PERFORMANCE
4.1. Tailpipe emission-control system
4.1.1.L1e — L7eBrief description and schematic drawing of the tailpipe emission-control system and its control:
4.1.2. Catalytic converter
4.1.2.1.L1e — L7eConfiguration, number of catalytic converters and elements (information to be provided for each separate unit): …
4.1.2.2.L1e — L7eDrawing with dimensions, shape and volume of the catalytic converter(s): …
4.1.2.3.L1e — L7eCatalytic reaction: …
* 4.1.2.4.L1e — L7eTotal charge of precious metals: …
* 4.1.2.5.L1e — L7eRelative concentration: …
* 4.1.2.6.L1e — L7eSubstrate (structure and material): …
* 4.1.2.7.L1e — L7eCell density: …
* 4.1.2.8.L1e — L7eCasing for the catalytic converter(s): …
4.1.2.9.L1e — L7eLocation of the catalytic converter(s) (place and reference distance in the exhaust line): …
4.1.2.10.L1e — L7eCatalyst heat-shield: yes/no(4)
4.1.2.11.L1e — L7eBrief description and schematic drawing of the regeneration system/method of exhaust after-treatment systems and its control system: …
4.1.2.11.1.L1e — L7eNormal operating temperature range: … K
4.1.2.11.2.L1e — L7eConsumable reagents: yes/no(4)
4.1.2.11.3.L1e — L7eBrief description and schematic drawing of the reagent flow (wet) system and its control system: …
4.1.2.11.4.L1e — L7eType and concentration of reagent needed for catalytic action: …
4.1.2.11.5.L1e — L7eNormal operational temperature range of reagent: … K
4.1.2.12.L1e — L7eIdentifying part number: …
4.1.3. Oxygen sensor(s)
4.1.3.1.L1e — L7eOxygen sensor component(s) drawing(s): …
4.1.3.2.L1e — L7eDrawing of exhaust device with oxygen sensor location(s) (dimensions relative to exhaust valves): …
4.1.3.3.L1e — L7eControl range(s): …
4.1.3.4.L1e — L7eIdentifying part number(s): …
4.1.3.5.L1e — L7eDescription of oxygen sensor heating system and heating strategy: …
4.1.3.6.L1e — L7eOxygen sensor heat shield(s): yes/no(4)
4.1.4. Secondary air-injection (air-inject in exhaust)
4.1.4.1.L1e — L7eBrief description and schematic drawing of the secondary air-injection system and its control system: …
4.1.4.2.L1e — L7eConfiguration (mechanical, pulse air, air pump etc.)(4): …
4.1.4.3.L1e — L7eWorking principle: …
4.1.5. External exhaust gas recirculation (EGR)
4.1.5.1.L1e — L7eBrief description and schematic drawing of the EGR system (exhaust flow) and its control system: …
4.1.6. Particulate filter
4.1.6.1.L1e — L7ePT component drawing with dimensions, shape and capacity of the particulate filter: …
4.1.6.2.L1e — L7eDesign of the particulate filter: …
4.1.6.3.L1e — L7eBrief description and schematic drawing of the particulate filter and its control system: …
4.1.6.4.L1e — L7eLocation (reference distance in the exhaust line): …
4.1.6.5.L1e — L7eMethod or system of regeneration, description and drawing: …
4.1.6.6.L1e — L7eIdentifying part number: …
4.1.7. Lean NOx trap
4.1.7.1.L1e — L7eOperation principle of lean NOx trap: …
4.1.8. Additional tailpipe emission-control devices (if any not covered under another heading)
4.1.8.1.L1e — L7eWorking principle: …
5. VEHICLE PROPULSION FAMILY
5.1.L1e — L7eTo define the vehicle propulsion family, the manufacturer shall submit the information required for classification criteria set out in point 3 of Annex XI to Commission Delegated Regulation (EU) No 134/2014, if not already provided in the information document.