Annex I

United Kingdom

Annex I to Implementing Regulation (EU) 2015/504 is amended as follows:

(1)

in the list of appendices, the row relating to Appendix 8 is replaced by the following:

‘

8 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) the installation of rear-view mirrors as a system

’
(2)
Part A is amended as follows:
1. (a)
  
  in point 1.1., the following point (j) is added:
  
  ‘(j)
  
  For vehicles of categories T2, T3 and T4.3 equipped with foldable ROPS with an automatic locking system, a certificate of the manufacturer stating that the preliminary test has been done according to the test procedure set out in point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014^f1.’
2. (b)
  
  in point 2., in the Explanatory notes relating to the information folder sheet, explanatory note (5) is amended as follows:
  
  ‘(5)
  
  For engines indicate the information relative to the engine type or the engine family type, as applicable without the type-approval extension number.’

(3)

Part B is amended as follows:

(a)

in point 3.1., Table 1-1 is replaced by the following:

‘

Table 1-1

Lists of systems, components and separate technical units which may be subject to an EU type-approval

Commission Delegated Regulation (EU) 2015/96 of 1 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council as regards environmental and propulsion unit performance requirements of agricultural and forestry vehicles (OJ L 16, 23.1.2015, p. 1).

Commission Delegated Regulation (EU) 2015/68 of 15 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle braking requirements for the approval of agricultural and forestry vehicles (OJ L 17, 23.1.2015, p. 1).

LIST I — Environmental and propulsion unit performance requirements
Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) 2015/96^f2 Annex number As amended by and/or at the stage of implementation
1 System: installation of an engine/engine family II
2 System: external sound level III
3 Component/STU: engine/engine family I
LIST II — Vehicle functional safety requirements
Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) 2015/208 Annex number As amended by and/or at the stage of implementation
4 System: driver information X
5 System: installation of lighting and light-signalling devices XII
6 System: electro-magnetic compatibility XV
7 System: installation of audible warning device(s) XVI
8 System: installation of rear-view mirrors IX
9 System: installation of crawler undercarriage XXXIII
10 STU: electro-magnetic compatibility of electrical / electronic sub-assemblies XV
11 Component/STU: ballast masses XXIII
12 Component/STU: lateral and/or rear protective structure XXVI / XXVII
13 Component: tyre XXX
14 Component/STU: mechanical coupling XXXIV
LIST III — Vehicle braking requirements
Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) 2015/68^f3 Annex number As amended by and/or at the stage of implementation
15 System: braking II
LIST IV — Vehicle construction and general type-approval requirements
Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) No 1322/2014 Annex number As amended by and/or at the stage of implementation
16 System: driver's exposure to noise level XIII
17 System: seat-belt anchorages XVIII
18 System: protection against hazardous substances XXIX
19 STU: roll-over protective structure (ROPS) VI / VII / VIII / IX / X
20 STU: falling objects protective structure (FOPS) XI
21 Component/STU: driver's seat XIV
22 Component/STU: safety belts XIX
23 STU: protection against penetrating objects (OPS) XX

’

Commission Delegated Regulation (EU) 2015/96 of 1 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council as regards environmental and propulsion unit performance requirements of agricultural and forestry vehicles (OJ L 16, 23.1.2015, p. 1).
Commission Delegated Regulation (EU) 2015/68 of 15 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle braking requirements for the approval of agricultural and forestry vehicles (OJ L 17, 23.1.2015, p. 1).
LIST I — Environmental and propulsion unit performance requirements
Appendix	System or component/separate technical unit (STU)	Commission Delegated Regulation (EU) 2015/96^f2 Annex number	As amended by and/or at the stage of implementation
1	System: installation of an engine/engine family	II
2	System: external sound level	III
3	Component/STU: engine/engine family	I
LIST II — Vehicle functional safety requirements
Appendix	System or component/separate technical unit (STU)	Commission Delegated Regulation (EU) 2015/208 Annex number	As amended by and/or at the stage of implementation
4	System: driver information	X
5	System: installation of lighting and light-signalling devices	XII
6	System: electro-magnetic compatibility	XV
7	System: installation of audible warning device(s)	XVI
8	System: installation of rear-view mirrors	IX
9	System: installation of crawler undercarriage	XXXIII
10	STU: electro-magnetic compatibility of electrical / electronic sub-assemblies	XV
11	Component/STU: ballast masses	XXIII
12	Component/STU: lateral and/or rear protective structure	XXVI / XXVII
13	Component: tyre	XXX
14	Component/STU: mechanical coupling	XXXIV
LIST III — Vehicle braking requirements
Appendix	System or component/separate technical unit (STU)	Commission Delegated Regulation (EU) 2015/68^f3 Annex number	As amended by and/or at the stage of implementation
15	System: braking	II
LIST IV — Vehicle construction and general type-approval requirements
Appendix	System or component/separate technical unit (STU)	Commission Delegated Regulation (EU) No 1322/2014 Annex number	As amended by and/or at the stage of implementation
16	System: driver's exposure to noise level	XIII
17	System: seat-belt anchorages	XVIII
18	System: protection against hazardous substances	XXIX
19	STU: roll-over protective structure (ROPS)	VI / VII / VIII / IX / X
20	STU: falling objects protective structure (FOPS)	XI
21	Component/STU: driver's seat	XIV
22	Component/STU: safety belts	XIX
23	STU: protection against penetrating objects (OPS)	XX

(b)

point 5 is amended as follows:

(i)

entry 1.6.1.1. is deleted;
(ii)

the following entry 1.6.3. is inserted:

‘1.6.3.

The vehicle identification number of the type begins with: …’;
(iii)

entry 2.5.1. is replaced by the following:

‘2.5.1.

Type-approval of: engine type/engine family⁽⁴⁾ ’;
(iv)

entry 3.3. is replaced by the following:

‘3.3.

Axles and wheels:’;
(v)

entry 4.1.2.1.2. is replaced by the following:

‘4.1.2.1.2.

In the case of a rigid drawbar or centre-axle R- or S-category vehicle indicate the vertical load on the front coupling point (S):… kg’;

(vi)

entry 4.1.2.2. is replaced by the following:

‘4.1.2.2.

Mass(es) and tyre(s)

According to the tyre specification.

Load transmitted to the reference centre of the coupling under static conditions, irrespective to the coupling device; if the maximum permissible vertical load on the coupling point depending on the coupling is indicated in this table, expand the table at the right side and indicate the identification of the coupling device in the header of the column; for R- or S-category vehicles this column(s) concerns the rear coupling devices if there is such a device.

Value to be provided only if the maximum permissible vertical load on the coupling point is lower than indicated in entries 38.3 and 38.4

Tyre combi-nation No Axle No Tyre dimension incl load capacity index & speed category symbol Rolling radius(1) [mm] Tyre Load rating per tyre [kg] Maximum permissible mass per axle [kg]^f4 Maximum permissible mass of the vehicle [kg] Maximum permissible vertical load on the coupling point [kg] ^f5 ^f6 Track width [mm]
Minimum Maximum
1 1 … … … … … … …
2 … … … … … … …
… … … … … … … …
2 1 … … … … … … …
2 … … … … … … …
… … … … … … … …
… 1 … … … … … … …
2 … … … … … … …
… … … … … … … …

’;

(vii)

entry 4.1.2.4. is deleted;

According to the tyre specification.
Load transmitted to the reference centre of the coupling under static conditions, irrespective to the coupling device; if the maximum permissible vertical load on the coupling point depending on the coupling is indicated in this table, expand the table at the right side and indicate the identification of the coupling device in the header of the column; for R- or S-category vehicles this column(s) concerns the rear coupling devices if there is such a device.
Value to be provided only if the maximum permissible vertical load on the coupling point is lower than indicated in entries 38.3 and 38.4
Tyre combi-nation No	Axle No	Tyre dimension incl load capacity index & speed category symbol	Rolling radius(1) [mm]	Tyre Load rating per tyre [kg]	Maximum permissible mass per axle [kg]^f4	Maximum permissible mass of the vehicle [kg]	Maximum permissible vertical load on the coupling point [kg] ^f5 ^f6	Track width [mm]
Minimum	Maximum
1	1	…		…	…	…	…	…	…
2	…		…	…	…	…	…	…
…	…		…	…	…	…	…	…
2	1	…		…	…	…	…	…	…
	2	…		…	…	…	…	…	…
	…	…		…	…	…	…	…	…
…	1	…		…	…	…	…	…	…
	2	…		…	…	…	…	…	…
	…	…		…	…	…	…	…	…

(viii)

entry 4.1.3. is replaced by the following:

‘4.1.3.

Technically permissible towable mass(es) for T- or C-category vehicles for each chassis/ braking configuration of the R- or S-category vehicle (for R- and S-category vehicles, indicate the maximum permissible load(s) on the rear coupling point):

Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.

R- and S category vehicleBrake Drawbar Rigid drawbar Centre-axle
Unbraked^f7 … kg … kg … kg
Inertia-braked … kg … kg … kg
Hydraulic braked … kg … kg … kg
Pneumatic braked … kg … kg … kg

’

(ix)

entry 4.1.4. is replaced by the following:

‘4.1.4.

Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle:

R- and S category vehicleBrake Drawbar Rigid drawbar Centre-axle
Unbraked … kg … kg … kg
Inertia-braked … kg … kg … kg
Hydraulic braked … kg … kg … kg
Pneumatic braked … kg … kg … kg

’;
(x)

entries 4.1.5. to 4.1.5.3. are deleted;
(xi)

entry 4.2.1.3. is replaced by the following:

‘4.2.1.3.

Height (in running order)⁽³³⁾ ’;
(xii)

the following entries 4.2.1.3.1. and 4.2.1.3.2. are inserted after entry 4.2.1.3.:

‘4.2.1.3.1.

Maximum … mm

4.2.1.3.2.

Minimum … mm’;
(xiii)

entry 5.1.2.2. is deleted;
(xiv)

entry 5.6. is replaced by the following:

‘5.6.

Actual forward movement of powered wheels corresponding to one complete revolution of the wheel: … mm’;
(xv)

entries 6.6. and 6.7. are replaced by the following:

‘6.6.

Rated speed: … min^–1

6.7.

Maximum torque speed: … min^–1 ’;
(xvi)

entry 6.18., including all its sub-entries, is replaced by the following:

‘6.18.

Fuel feed for diesel engines

6.18.1.

Feed pump

6.18.1.1

Pressure⁽⁷⁾ … kPa or characteristic diagram: …

6.18.2.

Injection system

6.18.2.1.

Pump

6.18.2.1.1.

Make(s): …

6.18.2.1.2.

Type(s): …

6.18.2.1.3.

Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …

6.18.2.1.3.1.

Method used: on engine/on pump bench⁽⁴⁾

6.18.2.2.

Injection advance:

6.18.2.2.1.

Injection advance curve⁽⁷⁾: …

6.18.2.2.2.

Timing⁽⁷⁾: …

6.18.2.3.

Injection piping:

6.18.2.3.1.

Length: … mm

6.18.2.3.2.

Internal diameter: … mm

6.18.2.4.

Injector(s)

6.18.2.4.1.

Make(s) …

6.18.2.4.2.

Type(s): …

6.18.2.4.3.

Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …

6.18.2.5.

Governor

6.18.2.5.1.

Make(s) …

6.18.2.5.2.

Type(s): …

6.18.2.5.3.

Speed at which cut-off starts under full load⁽⁷⁾: … min^{– 1}

6.18.2.5.4.

Maximum no-load speed⁽⁷⁾: … min^{– 1}

6.18.2.5.5.

Idling speed⁽⁷⁾: … min^{– 1}

6.18.2.6.

Cold-start system

6.18.2.6.1.

Make(s): …

6.18.2.6.2.

Type(s): …

6.18.2.6.3.

Description: …’;
(xvii)

entry 6.19.4.2. is replaced by the following:

‘6.19.3.2.

Type(s): …’;
(xviii)

entry 7.1.1. is replaced by the following:

‘7.1.1.

Combustion cycle: positive ignition/compression ignition⁽⁴⁾ ’;
(xix)

entries 8.6. and 8.7. are replaced by the following:

‘8.6.

Rated speed: … min^–1

8.7.

Maximum torque speed: … min^–1 ’;
(xx)

entry 8.12.2., including all its sub-entries, is replaced by the following:

‘8.12.2.

Air

8.12.2.1.

Blower: yes/no(4)

8.12.2.1.1.

Characteristics of the blower. …

8.12.2.1.2.

Drive ratio(s) (if applicable): …’;
(xxi)

entry 8.17., including all its sub-entries, is replaced by the following:

‘8.17.

Measures taken against air pollution

8.17.1.

Device for recycling crankcase gases: yes/no⁽⁴⁾

8.17.2.

Additional anti-pollution devices (if any):

8.17.2.1.

Catalytic converter: yes/no⁽⁴⁾

8.17.2.1.1.

Make: …

8.17.2.1.2.

Type …

8.17.2.1.3.

Number of catalytic converters and elements …

8.17.2.1.4.

Dimensions and volume of the catalytic converter(s): …

8.17.2.1.5.

Type of catalytic action …

8.17.2.1.6.

Total charge of precious metals: …

8.17.2.1.7.

Relative concentration: …

8.17.2.1.8.

Substrate (structure and material): …

8.17.2.1.9.

Cell density: …

8.17.2.1.10.

Type of casing for the catalytic converter(s): …

8.17.2.1.11.

Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: …

8.17.2.1.12.

Normal operating range: … K

8.17.2.1.13.

Consumable reagent (where appropriate) …

8.17.2.1.13.1.

Type and concentration of reagent needed for catalytic action: …

8.17.2.1.13.2.

Normal operational temperature range of reagent: … K

8.17.2.1.13.3.

International standard (if applicable): …

8.17.2.1.14.

NO_x sensor: yes/no⁽⁴⁾

8.17.2.1.15.

Oxygen sensor: yes/no⁽⁴⁾

8.17.2.1.15.1.

Make: …

8.17.2.1.15.2.

Type …

8.17.2.1.15.3.

Location: …

8.17.2.1.16.

Air injection: yes/no⁽⁴⁾

8.17.2.1.16.1.

Type: pulse air/air pump/other⁽⁴⁾ (if other specify: …)

8.17.2.1.17.

EGR: yes/no⁽⁴⁾

8.17.2.1.17.1.

Characteristics (cooled/uncooled, high pressure/low pressure, etc.): …

8.17.2.1.18.

Particulate trap: yes/no⁽⁴⁾

8.17.2.1.18.1.

Dimensions and capacity of the particulate trap: …

8.17.2.1.18.2.

Type and design of the particulate trap: …

8.17.2.1.18.3.

Location (place(s) and maximum/minimum distance(s) from engine: …

8.17.2.1.18.4.

Method or system of regeneration, description and/or drawing: …

8.17.2.1.18.5.

Normal operating temperature range: … K and pressure range: …kPa

8.17.2.1.19.

Other systems: yes/no⁽⁴⁾

8.17.2.1.19.1.

Description and operation: …’;
(xxii)

entry 8.18., including all its sub-entries, is replaced by the following:

‘8.18.

Fuel feed for diesel engines

8.18.1.

Feed pump

8.18.1.1

Pressure⁽⁷⁾ … kPa or characteristic diagram: …

8.18.2.

Injection system

8.18.2.1.

Pump

8.18.2.1.1.

Make(s): …

8.18.2.1.2.

Type(s): …

8.18.2.1.3.

Delivery: … and …mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …

8.18.2.1.3.1.

Method used: on engine/on pump bench⁽⁴⁾

8.18.2.2.

Injection advance:

8.18.2.2.1.

Injection advance curve⁽⁷⁾: …

8.18.2.2.2.

Timing⁽⁷⁾: …

8.18.2.3.

Injection piping:

8.18.2.3.1.

Length: … mm

8.18.2.3.2.

Internal diameter: … mm

8.18.2.4.

Injector(s)

8.18.2.4.1.

Make(s) …

8.18.2.4.2.

Type(s): …

8.18.2.4.3.

Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …

8.18.2.5.

Governor

8.18.2.5.1.

Make(s) …

8.18.2.5.2.

Type(s): …

8.18.2.5.3.

Speed at which cut-off starts under full load⁽⁷⁾: … min^–1

8.18.2.5.4.

Maximum no-load speed⁽⁷⁾: … min^–1

8.18.2.5.5.

Idling speed⁽⁷⁾: … min^–1

8.18.2.6.

Cold-start system

8.18.2.6.1.

Make(s): …

8.18.2.6.2.

Type(s): …

8.18.2.6.3.

Description: …’;
(xxiii)

entry 8.19. is replaced by the following:

‘8.19.

Fuel feed for petrol engines ’;
(xxiv)

entry 9., including all its sub-entries, is replaced by the following:

‘9.

ENERGY STORAGE DEVICE(S)⁽¹¹⁾

9.1.

Description: battery/capacitor/flywheel/generator(4)

9.2.

Identification number: …

9.3.

Kind of electrochemical couple: …

9.4.

Energy stored

9.4.1.

For battery, voltage: … and capacity: … Ah in 2h

9.4.2.

For capacitor: … J

9.4.3.

For flywheel/generator⁽⁴⁾: … J

9.4.3.1.

Flywheel moment of inertia: … kg m²

9.4.3.1.1.

Additional moment of inertia if no gear is engaged: … kg m²

9.5.

Charger: on-board/external/without⁽⁴⁾ ’;
(xxv)

entry 10.4.4.1. is replaced by the following:

‘10.4.4.1.

Exhaust noise-abatement device containing fibrous materials: yes/no⁽⁴⁾ ’;

Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.
R- and S category vehicleBrake	Drawbar	Rigid drawbar	Centre-axle
Unbraked^f7	… kg	… kg	… kg
Inertia-braked	… kg	… kg	… kg
Hydraulic braked	… kg	… kg	… kg
Pneumatic braked	… kg	… kg	… kg

R- and S category vehicleBrake	Drawbar	Rigid drawbar	Centre-axle
Unbraked	… kg	… kg	… kg
Inertia-braked	… kg	… kg	… kg
Hydraulic braked	… kg	… kg	… kg
Pneumatic braked	… kg	… kg	… kg

(xxvi)

entry 11., including all its sub-entries, is replaced by the following:

‘11.

DRIVE-TRAIN AND CONTROL⁽¹³⁾

11.1.

Brief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train):

11.2.

Transmission

11.2.1.

Brief description and schematic drawing of gear shift system(s) and its control: …

11.2.2.

Diagram and or drawing of the transmission system: …

11.2.3.

Type of transmission: mechanical/hydraulic/electric/other⁽⁴⁾ (if other specify …)

11.2.4.

Brief description of the electrical/electronic components (if any): …

11.2.5.

Location relative to the engine: …

11.2.6.

Method of control: …

11.2.7.

Transfer box: with/without⁽⁴⁾

11.2.8.

Type of gear shift system(s)⁽²⁴⁾: …

11.3.

Clutch (if any)

11.3.1.

Brief description and schematic drawing of the clutch and its control system:

11.3.2.

Maximum torque conversion: …

11.4.

Gear ratios

Continuously variable transmission

Gear Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions) Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions) Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions) Total gear ratios Ratio (engine speed/vehicle speed) for manual transmission only

Maximum for CVT^f8

1

2

3

Minimum for CVT

Reverse

1

…

11.5.

Differential lock

11.5.1.

Differential lock: yes/no/optional⁽⁴⁾ ’;

(xxvii)

entry 22.3.1. is replaced by the following:

‘22.3.1.

Photographs, drawings and/or an exploded view of the interior fittings, showing the parts in the passenger compartment and the materials used (with the exception of interior rear view mirrors), arrangement of controls, seats and their rear parts, head restraints, roof and opening roof, doors and window winders and other non-specified fittings: …’;
(xxviii)

entry 25.5.2. is replaced by the following:

‘25.5.2.

Rated voltage or air pressure: … V / kPa(4)’;
(xxix)

entry 28., including all its sub-entries, is replaced by the following:

‘28.

REAR REGISTRATION PLATE(S) SPACE

28.1.

Location of registration plate(s) (indicate variants where necessary; drawings may be used as appropriate):

28.1.1.

Height above road surface, upper edge: …mm

28.1.2.

Height above road surface, lower edge: …mm

28.1.3.

Distance of the centre line from the longitudinal median plane of the vehicle: …mm

28.1.4.

Dimensions (length x width): …mm x …mm

28.1.5.

Inclination of the plane to the vertical: …degr.

28.1.6.

Angle of visibility in the horizontal plane: ….degr.’
(xxx)

entry 29., including all its sub-entries, is replaced by the following:

‘29.

BALLAST MASSES

29.1.

Detailed technical description (including photographs or drawings with dimensions) of the ballast masses and how they are mounted on the tractor:

29.2.

Number of sets of ballast masses: …

29.2.1.

Number of components on each set: Set 1: … Set 2: …Set …

29.3.

Mass of the components on each set: Set 1: …kg Set 2: …kg Set …:…kg

29.3.1.

Total mass of each set: Set 1: …kg Set 2: …kg Set …:…kg

29.4.

Total mass of ballast masses: …kg

29.4.1.

Distribution of these masses among the axles: …kg

29.5.

Material(s) and method of construction: …’;

(xxxi)

entry 38.5. is replaced by the following:

‘38.5.

Description of the mechanical coupling:

Type (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208): …
Make: …
Manufacturer’s type designation: …
Maximum horizontal load/D-Value^(4)(44): … kg/kN⁽⁴⁾
Towable mass (T) ^(4)(44): … tonnes
Maximum permissible vertical load on the coupling point (S)⁽⁴⁴⁾: … kg
Photographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.
Short technical description of the coupling device specifying the type of construction and the material used.
Type of Test Static/Dynamic ⁽⁴⁾

(EU) type-approval mark or -number of

drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars)

type-approval mark or –number of mechanical couplings that shall be attached to the ladder frame /trailer hitch support (if restricted to certain types):

…

’;

(xxxii)

the following entry 39.2. is inserted:

‘39.2.

Maximum towable mass⁽¹⁶⁾: … kg’;
(xxxiii)

entry 43.1. is replaced by the following:

‘43.1.

Brief description of the braking system(s) installed on the vehicle⁽⁵⁵⁾: …’;
(xxxiv)

entry 43.3. is deleted;
(xxxv)

entry 43.6., including all its sub-entries, is replaced by the following:

‘43.6.

Towed vehicle braking devices

43.6.1.

Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None⁽⁴⁾

43.6.2.

Towed vehicle-brake actuating device (description, characteristics): …

43.6.3.

Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …

43.6.4.

Connections type: Single line/Two-lines/None⁽⁴⁾

43.6.4.1.

Supply pressure Hydraulic: Single line: … kPa Two lines: … kPa

43.6.4.2.

Supply pressure Pneumatic: Two lines: … kPa

43.6.5.

Presence of ISO 7638:2003 connector⁽¹⁵⁾: yes/no⁽⁴⁾ ’;
(xxxvi)

before the heading ‘E. Information on vehicle construction’, the following entries are inserted:

‘43.A.

TOWED VEHICLE AXLE AND BRAKE INFORMATION DOCUMENT WITH RESPECT TO THE ALTERNATIVE TYPE I AND TYPE III PROCEDURE

43.A.1.

General

43.A.1.1.

Name and address of axle or vehicle manufacturer:

43.A.2.

Axle data

43.A.2.1.

Manufacturer (name and address): …

43.A.2.2.

Type/variant: …

43.A.2.3.

Axle identifier: ID1- …

43.A.2.4.

Test axle load (F_e): … daN

43.A.2.5.

Wheel and brake data according to the following figures 1A and 1B …

43.A.3.

Brake

43.A.3.1.

General information

43.A.3.1.1.

Make:

43.A.3.1.2.

Manufacturer (name and address):

43.A.3.1.3.

Type of brake (e.g. drum / disc):

43.A.3.1.3.1.

Variant (e.g. S-cam, single wedge etc.):

43.A.3.1.4.

Brake identifier: ID2-

43.A.3.1.5.

Brake data according to the figures 2A and 2B:

43.A.3.2.

Drum brake data

43.A.3.2.1.

Brake adjustment device (external/integrated): …

43.A.3.2.2.

Declared maximum brake input torque C_max: … Nm

43.A.3.2.3.

Mechanical efficiency: η = …

43.A.3.2.4.

Declared brake input threshold torque C0,dec: … Nm

43.A.3.2.5.

Effective length of the cam shaft: … mm

43.A.3.3.

Brake drum

43.A.3.3.1.

Max diameter of friction surface (wear limit) … mm

43.A.3.3.2.

Base material: …

43.A.3.3.3.

Declared mass: … kg

43.A.3.3.4.

Nominal mass: … kg

43.A.3.4.

Brake lining

43.A.3.4.1.

Manufacturer and address …

43.A.3.4.2.

Make …

43.A.3.4.3.

Type …

43.A.3.4.4.

Identification (type identification on lining) …

43.A.3.4.5.

Minimum thickness (wear limit) … mm

43.A.3.4.6.

Method of attaching friction material to brake shoe: …

43.A.3.4.6.1.

… Worst case of attachment (in the case of more than one):

43.A.3.5.

Disc brake data

43.A.3.5.1.

Connection type to the axle (axial, radial, integrated, etc.): …

43.A.3.5.2.

Brake adjustment device (external/integrated): …

43.A.3.5.3.

Max. actuation stroke: … mm

43.A.3.5.4.

Declared maximum input force Th_Amax: … daN

43.A.3.5.4.1

Cmax = ThAmax · l_e : … Nm

43.A.3.5.5.

Friction radius: r_e = … mm

43.A.3.5.6.

Lever length: l_e = … mm

43.A.3.5.7.

Input/output ratio (l_e/e_e): i = ….

43.A.3.5.8.

Mechanical efficiency: η = …

43.A.3.5.9.

Declared brake input threshold force Th_A0,dec: … N

43.A.3.5.9.1.

C_0,dec = Th_A0,dec · l_e : … Nm

43.A.3.5.10.

Minimum rotor thickness (wear limit): … mm

43.A.3.6.

Brake disc data …

43.A.3.6.1.

Disc type description: …

43.A.3.6.2.

Connection/mounting to the hub: …

43.A.3.6.3.

Ventilation (yes/no): …

43.A.3.6.4.

Declared mass: … kg

43.A.3.6.5.

Nominal mass: … kg

43.A.3.6.6.

Declared external diameter: … mm

43.A.3.6.7.

Minimum external diameter: … mm

43.A.3.6.8.

Inner diameter of friction ring: … mm

43.A.3.6.9.

Width of ventilation channel (if appl.): … mm

43.A.3.6.10.

Base material: …

43.A.3.7.

Brake pad data …

43.A.3.7.1.

Manufacturer and address: …

43.A.3.7.2.

Make:

43.A.3.7.3.

Type: …

43.A.3.7.4.

Identification (type identification on pad back plate): …

43.A.3.7.5.

Minimum thickness (wear limit): … mm

43.A.3.7.6.

Method of attaching friction material to pad back plate: …

43.A.3.7.6.1.

Worst case of attachment (in the case of more than one): …

Figure 1A

Figure 1B

Figure 2A

Figure 2B

xe (mm) ae (mm) he (mm) ce (mm) de (mm) ee (mm) α0e α1e be (mm) re (mm) Ae (cm2) S1e (mm) S2e (mm) S3e (mm)

’;
(xxxvii)

entries 45.6.3.1. to 45.6.3.4. are replaced by the following:

‘45.6.3.1.

SAE J1939-13 (Serial control and communications vehicle network): yes/no⁽⁴⁾

45.6.3.2.

ISO 11783-2 (Tractors and machinery for agriculture and forestry – Serial control and communications data network): yes/no⁽⁴⁾

45.6.3.3.

ISO 15031-3 (Road vehicles – Communication between vehicle and external equipment for emissions-related diagnostics): yes/no⁽⁴⁾

45.6.3.4.

ISO 13400-4 (Road vehicles – Diagnostic communication over Internet Protocol (DoIP))⁽⁴⁾: yes/no⁽⁴⁾ ’;
(xxxviii)

entry 46.2.1. is replaced by the following:

‘46.2.1.

In the case of roll bar: foldable/not foldable⁽⁴⁾ ’;
(xxxix)

entry 46.2.2., including all its sub-entries, is replaced by the following:

‘46.2.2.

In the case of foldable roll bar:

46.2.2.1.

Folding operation: non-assisted / partially assisted / fully assisted⁽⁴⁾

46.2.2.2.

In case of non-assisted or partially assisted folding operation:

46.2.2.2.1.

Hand-operated foldable ROPS: with tools/ without tools⁽⁴⁾

46.2.2.2.2.

Photographs and detailed technical drawings showing the grasping area and a lateral and top view of the accessible zones. Dimensions and maximum forces for actuating the ROPS must figure on the drawings: …

46.2.2.3.

In case of partially assisted or fully assisted folding operation, brief description of the assistance devices as well as of their control devices, if any, and their location: …

46.2.2.4.

Locking mechanism: manual/automatic⁽⁴⁾

46.2.2.4.1.

For manual locking mechanisms, brief description of the locking mechanism and of its ergonomic design to avoid pinching or shearing hazards and to limit the force required for its operation: …

46.2.2.4.2.

For automatic locking mechanisms,

46.2.2.4.2.1.

Brief description of the locking mechanism, its control devices, if any, and their location: …

46.2.2.4.2.2.

Manufacturers' certificate set out in Note 2 of point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014: yes/no⁽⁴⁾ ’;
(xxxx)

entry 49.4.1. is replaced by the following:

‘49.4.1.

Position of the driving seat: left/right/centre⁽⁴⁾ ’;
(xxxxi)

entry 49.5., including all its sub-entries, is replaced by the following:

‘49.5.

Passenger seat(s)

49.5.1.

Number of passenger seats: …

49.5.2.

Location and arrangement⁽⁸⁾: …

49.5.3.

Dimensions of the passenger seat(s): …

49.5.4.

Main characteristics of the passenger seat(s): …

49.5.5.

Requirements under standard EN 15694:2009 (Agricultural and forestry tractors. Passenger seat. Requirements and test procedures) are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾

49.5.6.

Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs - Quads). Safety requirements and test methods) on passenger seats for ATV Type II vehicle are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾ ’;
(xxxxii)

entry 51.2., including all its sub-entries, is replaced by the following:

‘51.2.

Main power take-off

51.2.1.

Position: front/rear/other⁽⁴⁾ (if other specify: …)

51.2.2.

Revolutions per minute: … min^–1

51.2.2.1.

Ratio of power take-off revolutions to that of the engine: …

51.2.3.

Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2⁽⁵⁷⁾ or ISO 789-1:1990 (Agricultural tractors – Test procedures – Part 1: Power tests for power take-off))

Rated speed PTO(min^–1) Corresponding engine speed(min^–1) Power(kW)
1-540 … …
2-1 000 … …
540E
1 000E

51.2.4.

Power take-off guard (description, dimensions, drawings, photographs): …’;
(xxxxiii)

entry 51.2.3. is replaced by the following:

‘51.3.3.

Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2⁽⁵⁷⁾ or ISO 789-1:1990 (Agricultural tractors – Test procedures – Part 1: Power tests for power take-off))

Rated speed PTO(min^–1) Corresponding engine speed(min^–1) Power(kW)
1-540 … …
2-1 000 … …
540E
1 000E

’

Rated speed PTO(min^–1)	Corresponding engine speed(min^–1)	Power(kW)
1-540	…	…
2-1 000	…	…
540E
1 000E

Rated speed PTO(min^–1)	Corresponding engine speed(min^–1)	Power(kW)
1-540	…	…
2-1 000	…	…
540E
1 000E

(xxxxiv)

entry 54.3. is replaced by the following:

‘54.3.

Number and position of safety belts and seats on which they can be used, please fill out table below:

Safety belt configuration and associated information

L = left, C = centre, R = right

Complete EU type-approval mark / ECE type-approval mark Variant, if applicable Belt adjustment device for height (indicate yes/no/optional)
Driver's seat L
C
R

Passenger seat

1
L
C
R

Passenger seat

…
L
C
R

’;

(xxxxv)

entry 57., including all its sub-entries, is replaced by the following:

‘57.

DRIVER-OPERATED CONTROL DEVICES INCLUDING IDENTIFICATION OF CONTROL DEVICES, TELL-TALES AND INDICATORS

57.1.

Photographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators:

57.2.

Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purpose

x

yes

–

no or not separately available

o

optional.

d

directly on control, indicator or tell-tale

c

in close vicinity.

Symbol No Device Control / indicator available^f9 Identified by symbol Where^f10 Tell-tale available Identified by symbol Where
1 Dipped-beam head lamps
2 Main-beam head lamps
3 Position (side) lamps
4 Front fog lamps
5 Rear fog lamp
6 Headlamp levelling device
7 Parking lamps
8 Direction indicators
9 Hazard warning
10 Windscreen wiper
11 Windscreen washer
12 Windscreen wiper and washer
13 Headlamp cleaning device
14 Windscreen demisting and defrosting
15 Rear window demisting and defrosting
16 Ventilating fan
17 Diesel pre-heat
18 Choke
19 Brake failure
20 Fuel level
21 Battery charging condition
22 Engine coolant temperature
23 Malfunction indicator light (MI)

57.3.

Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which shall be used if they are to be identified

x

yes

–

no or not separately available

o

optional.

d

directly on control, indicator or tell-tale

c

in close vicinity.

Symbol No Device Control / indicator available^f11 Identified by symbol Where^f12 Tell-tale available Identified by symbol Where
1 Parking brake
2 Rear window wiper
3 Rear window washer
4 Rear window wiper and washer
5 Intermittent windscreen wiper
6 Audible warning device
7 Hood
8 Seat belt
9 Engine oil pressure
10 Unleaded petrol
11 …
12 ….

57.4.

Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the interior of the vehicle and showing for tractors without enclosed cab, how the accessibility to internal control devices from the ground has been avoided: …

57.5.

Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the exterior of the vehicle and indicating the front and the rear hazard zones in accordance with Appendix 1 of Annex XXIII to Commission Delegated Regulation (EU) No 1322/2014: …

57.6.

Requirements under Annexes A and C of standard ISO 15077:2008 (Tractors and self-propelled machinery for agriculture – Operator controls – Actuating forces, displacement, location and method of operation) are met with relevant documentation included in the information document: yes/no⁽⁴⁾

57.7.

Requirements under paragraph 4.5.3 of standard ISO 4254-1:2013 (Agricultural machinery – Safety – Part 1: General requirements), with the exception of fingertip operation control devices, are met with relevant documentation included in the information document: yes/no⁽⁴⁾

57.8.

Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs - Quads). Safety requirements and test methods) on throttle control and manual clutch control are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾

57.9.

For vehicles of T- and C-category, requirements under standard ISO 10975:2009 (Tractors and machinery for agriculture – Auto-guidance systems for operator-controlled tractors and self-propelled machines – Safety requirements) are met with relevant documentation included in the information document: yes/no/not applicable⁽⁴⁾ ’;

(c)
Appendix 1 is amended as follows:
1. (i)
  
  entry 2.5.1. is replaced by the following:
  
  ‘2.5.1.
  
  Type-approval of: engine type/engine family⁽⁴⁾ ’;
2. (ii)
  
  entry 5.1.2.2. is deleted;
3. (iii)
  
  entries 6.6. and 6.7. are replaced by the following:
  
  ‘6.6.
  
  Rated speed: … min^–1
  
  6.7.
  
  Maximum torque speed: … min^–1 ’;
4. (iv)
  
  entry 6.18., including all its sub-entries, is replaced by the following:
  
  ‘6.18.
  
  Fuel feed for diesel engines
  
  6.18.1.
  
  Feed pump
  
  6.18.1.1
  
  Pressure⁽⁷⁾ … kPa or characteristic diagram: …
  
  6.18.2.
  
  Injection system
  
  6.18.2.1.
  
  Pump
  
  6.18.2.1.1.
  
  Make(s): …
  
  6.18.2.1.2.
  
  Type(s): …
  
  6.18.2.1.3.
  
  Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …
  
  6.18.2.1.3.1.
  
  Method used: on engine/on pump bench⁽⁴⁾
  
  6.18.2.2.
  
  Injection advance:
  
  6.18.2.2.1.
  
  Injection advance curve⁽⁷⁾: …
  
  6.18.2.2.2.
  
  Timing⁽⁷⁾: …
  
  6.18.2.3.
  
  Injection piping:
  
  6.18.2.3.1.
  
  Length: … mm
  
  6.18.2.3.2.
  
  Internal diameter: … mm
  
  6.18.2.4.
  
  Injector(s)
  
  6.18.2.4.1.
  
  Make(s) …
  
  6.18.2.4.2.
  
  Type(s): …
  
  6.18.2.4.3.
  
  Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …
  
  6.18.2.5.
  
  Governor
  
  6.18.2.5.1.
  
  Make(s) …
  
  6.18.2.5.2.
  
  Type(s): …
  
  6.18.2.5.3.
  
  Speed at which cut-off starts under full load⁽⁷⁾: … min^–1
  
  6.18.2.5.4.
  
  Maximum no-load speed⁽⁷⁾: … min^–1
  
  6.18.2.5.5.
  
  Idling speed⁽⁷⁾: … min^–1
  
  6.18.2.6.
  
  Cold-start system
  
  6.18.2.6.1.
  
  Make(s): …
  
  6.18.2.6.2.
  
  Type(s): …
  
  6.18.2.6.3.
  
  Description: …’;
5. (v)
  
  entry 7.1.1. is replaced by the following:
  
  ‘7.1.1.
  
  Combustion cycle: positive ignition/compression ignition⁽⁴⁾ ’;
6. (vi)
  
  entries 8.6. and 8.7. are replaced by the following:
  
  ‘8.6.
  
  Rated speed: … min^–1
  
  8.7.
  
  Maximum torque speed: … min^–1 ’;
7. (vii)
  
  entry 8.12.2., including all its sub-entries, is replaced by the following:
  
  ‘8.12.2.
  
  Air
  
  8.12.2.1.
  
  Blower: yes/no⁽⁴⁾
  
  8.12.2.1.1.
  
  Characteristics of the blower. …
  
  8.12.2.1.2.
  
  Drive ratio(s) (if applicable): …’;
8. (viii)
  
  entry 8.17., including all its sub-entries, is replaced by the following:
  
  ‘8.17.
  
  Measures taken against air pollution
  
  8.17.1.
  
  Device for recycling crankcase gases: yes/no⁽⁴⁾
  
  8.17.2.
  
  Additional anti-pollution devices (if any):
  
  8.17.2.1.
  
  Catalytic converter: yes/no⁽⁴⁾
  
  8.17.2.1.1.
  
  Make: …
  
  8.17.2.1.2.
  
  Type …
  
  8.17.2.1.3.
  
  Number of catalytic converters and elements …
  
  8.17.2.1.4.
  
  Dimensions and volume of the catalytic converter(s): …
  
  8.17.2.1.5.
  
  Type of catalytic action …
  
  8.17.2.1.6.
  
  Total charge of precious metals: …
  
  8.17.2.1.7.
  
  Relative concentration: …
  
  8.17.2.1.8.
  
  Substrate (structure and material): …
  
  8.17.2.1.9.
  
  Cell density: …
  
  8.17.2.1.10.
  
  Type of casing for the catalytic converter(s): …
  
  8.17.2.1.11.
  
  Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: …
  
  8.17.2.1.12.
  
  Normal operating range: …K
  
  8.17.2.1.13.
  
  Consumable reagent (where appropriate) …
  
  8.17.2.1.13.1.
  
  Type and concentration of reagent needed for catalytic action: …
  
  8.17.2.1.13.2.
  
  Normal operational temperature range of reagent: … K
  
  8.17.2.1.13.3.
  
  International standard (if applicable): …
  
  8.17.2.1.14.
  
  NOx sensor: yes/no⁽⁴⁾
  
  8.17.2.1.15.
  
  Oxygen sensor: yes/no⁽⁴⁾
  
  8.17.2.1.15.1.
  
  Make: …
  
  8.17.2.1.15.2.
  
  Type …
  
  8.17.2.1.15.3.
  
  Location: …
  
  8.17.2.1.16.
  
  Air injection: yes/no⁽⁴⁾
  
  8.17.2.1.16.1.
  
  Type: pulse air/air pump/other(4) (if other specify: …)
  
  8.17.2.1.17.
  
  EGR: yes/no⁽⁴⁾
  
  8.17.2.1.17.1.
  
  Characteristics (cooled/uncooled, high pressure/low pressure, etc.): …
  
  8.17.2.1.18.
  
  Particulate trap: yes/no⁽⁴⁾
  
  8.17.2.1.18.1.
  
  Dimensions and capacity of the particulate trap: …
  
  8.17.2.1.18.2.
  
  Type and design of the particulate trap: …
  
  8.17.2.1.18.3.
  
  Location (place(s) and maximum/minimum distance(s) from engine: …
  
  8.17.2.1.18.4.
  
  Method or system of regeneration, description and/or drawing: …
  
  8.17.2.1.18.5.
  
  Normal operating temperature range: … K and pressure range: … kPa
  
  8.17.2.1.19.
  
  Other systems: yes/no⁽⁴⁾
  
  8.17.2.1.19.1.
  
  Description and operation:… .’
9. (ix)
  
  entry 8.18., including all its sub-entries, is replaced by the following:
  
  ‘8.18.
  
  Fuel feed for diesel engines
  
  8.18.1.
  
  Feed pump
  
  8.18.1.1
  
  Pressure⁽⁷⁾ … kPa or characteristic diagram: …
  
  8.18.2.
  
  Injection system
  
  8.18.2.1.
  
  Pump
  
  8.18.2.1.1.
  
  Make(s): …
  
  8.18.2.1.2.
  
  Type(s): …
  
  8.18.2.1.3.
  
  Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …
  
  8.18.2.1.3.1.
  
  Method used: on engine/on pump bench⁽⁴⁾
  
  8.18.2.2.
  
  Injection advance:
  
  8.18.2.2.1.
  
  Injection advance curve⁽⁷⁾: …
  
  8.18.2.2.2.
  
  Timing⁽⁷⁾: …
  
  8.18.2.3.
  
  Injection piping:
  
  8.18.2.3.1.
  
  Length: … mm
  
  8.18.2.3.2.
  
  Internal diameter: … mm
  
  8.18.2.4.
  
  Injector(s)
  
  8.18.2.4.1.
  
  Make(s) …
  
  8.18.2.4.2.
  
  Type(s): …
  
  8.18.2.4.3.
  
  Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …
  
  8.18.2.5.
  
  Governor
  
  8.18.2.5.1.
  
  Make(s) …
  
  8.18.2.5.2.
  
  Type(s): …
  
  8.18.2.5.3.
  
  Speed at which cut-off starts under full load⁽⁷⁾: … min^–1
  
  8.18.2.5.4.
  
  Maximum no-load speed⁽⁷⁾: … min^–1
  
  8.18.2.5.5.
  
  Idling speed⁽⁷⁾: … min^–1
  
  8.18.2.6.
  
  Cold-start system
  
  8.18.2.6.1.
  
  Make(s): …
  
  8.18.2.6.2.
  
  Type(s): …
  
  8.18.2.6.3.
  
  Description: …’;
10. (x)
  
  entry 8.19. is replaced by the following:
  
  ‘8.19.
  
  Fuel feed for petrol engines ’;
(d)
Appendix 2 is amended as follows:
1. (i)
  
  entry 2.5.1. is replaced by the following:
  
  ‘2.5.1.
  
  Type-approval of: engine type/engine family⁽⁴⁾ ’;
2. (ii)
  
  entry 5.1.2.2. is deleted;
3. (iii)
  
  entry 10.4.4.1. is replaced by the following:
  
  ‘10.4.4.1.
  
  Exhaust noise-abatement device containing fibrous materials: yes/no⁽⁴⁾ ’;
(e)
Appendix 3 is amended as follows:
1. (i)
  
  the following entry 2.2.4. is inserted:
  
  ‘2.2.4.
  
  For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
2. (ii)
  
  entry 2.5.1. is replaced by the following:
  
  ‘2.5.1.
  
  Type-approval of: engine type/engine family⁽⁴⁾ ’;
3. (iii)
  
  entries 6.6. and 6.7. are replaced by the following:
  
  ‘6.6.
  
  Rated speed: … min^–1
  
  6.7.
  
  Maximum torque speed: … min^–1 ’;
4. (iv)
  
  entry 6.18., including all its sub-entries, is replaced by the following:
  
  ‘6.18.
  
  Fuel feed for diesel engines
  
  6.18.1.
  
  Feed pump
  
  6.18.1.1
  
  Pressure⁽⁷⁾ … kPa or characteristic diagram: …
  
  6.18.2.
  
  Injection system
  
  6.18.2.1.
  
  Pump
  
  6.18.2.1.1.
  
  Make(s): …
  
  6.18.2.1.2.
  
  Type(s): …
  
  6.18.2.1.3.
  
  Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …
  
  6.18.2.1.3.1.
  
  Method used: on engine/on pump bench⁽⁴⁾
  
  6.18.2.2.
  
  Injection advance:
  
  6.18.2.2.1.
  
  Injection advance curve⁽⁷⁾: …
  
  6.18.2.2.2.
  
  Timing⁽⁷⁾: …
  
  6.18.2.3.
  
  Injection piping:
  
  6.18.2.3.1.
  
  Length: … mm
  
  6.18.2.3.2.
  
  Internal diameter: … mm
  
  6.18.2.4.
  
  Injector(s)
  
  6.18.2.4.1.
  
  Make(s) …
  
  6.18.2.4.2.
  
  Type(s): …
  
  6.18.2.4.3.
  
  Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …
  
  6.18.2.5.
  
  Governor
  
  6.18.2.5.1.
  
  Make(s) …
  
  6.18.2.5.2.
  
  Type(s): …
  
  6.18.2.5.3.
  
  Speed at which cut-off starts under full load⁽⁷⁾: … min^–1
  
  6.18.2.5.4.
  
  Maximum no-load speed⁽⁷⁾: … min^–1
  
  6.18.2.5.5.
  
  Idling speed⁽⁷⁾: … min^–1
  
  6.18.2.6.
  
  Cold-start system
  
  6.18.2.6.1.
  
  Make(s): …
  
  6.18.2.6.2.
  
  Type(s): …
  
  6.18.2.6.3.
  
  Description: …’;
5. (v)
  
  entry 6.19.4.2. is replaced by the following:
  
  ‘6.19.3.2.
  
  Type(s): …’;
6. (vi)
  
  entry 7.1.1. is replaced by the following:
  
  ‘7.1.1.
  
  Combustion cycle: positive ignition/compression ignition⁽⁴⁾ ’;
7. (vii)
  
  entries 8.6. and 8.7. are replaced by the following:
  
  ‘8.6.
  
  Rated speed: … min^–1
  
  8.7.
  
  Maximum torque speed: … min^–1 ’;
8. (viii)
  
  entry 8.12.2., including all its sub-entries, is replaced by the following:
  
  ‘8.12.2.
  
  Air
  
  8.12.2.1.
  
  Blower: yes/no⁽⁴⁾
  
  8.12.2.1.1.
  
  Characteristics of the blower. …
  
  8.12.2.1.2.
  
  Drive ratio(s) (if applicable): …’;
9. (ix)
  
  entry 8.17., including all its sub-entries, is replaced by the following:
  
  ‘8.17.
  
  Measures taken against air pollution
  
  8.17.1.
  
  Device for recycling crankcase gases: yes/no⁽⁴⁾
  
  8.17.2.
  
  Additional anti-pollution devices (if any):
  
  8.17.2.1.
  
  Catalytic converter: yes/no⁽⁴⁾
  
  8.17.2.1.1.
  
  Make: …
  
  8.17.2.1.2.
  
  Type …
  
  8.17.2.1.3.
  
  Number of catalytic converters and elements …
  
  8.17.2.1.4.
  
  Dimensions and volume of the catalytic converter(s): …
  
  8.17.2.1.5.
  
  Type of catalytic action …
  
  8.17.2.1.6.
  
  Total charge of precious metals: …
  
  8.17.2.1.7.
  
  Relative concentration: …
  
  8.17.2.1.8.
  
  Substrate (structure and material): …
  
  8.17.2.1.9.
  
  Cell density: …
  
  8.17.2.1.10.
  
  Type of casing for the catalytic converter(s): …
  
  8.17.2.1.11.
  
  Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: …
  
  8.17.2.1.12.
  
  Normal operating range: …K
  
  8.17.2.1.13.
  
  Consumable reagent (where appropriate) …
  
  8.17.2.1.13.1.
  
  Type and concentration of reagent needed for catalytic action: …
  
  8.17.2.1.13.2.
  
  Normal operational temperature range of reagent: … K
  
  8.17.2.1.13.3.
  
  International standard (if applicable): …
  
  8.17.2.1.14.
  
  NO_x sensor: yes/no⁽⁴⁾
  
  8.17.2.1.15.
  
  Oxygen sensor: yes/no⁽⁴⁾
  
  8.17.2.1.15.1.
  
  Make: …
  
  8.17.2.1.15.2.
  
  Type …
  
  8.17.2.1.15.3.
  
  Location: …
  
  8.17.2.1.16.
  
  Air injection: yes/no⁽⁴⁾
  
  8.17.2.1.16.1.
  
  Type: pulse air/air pump/other⁽⁴⁾ (if other specify: …)
  
  8.17.2.1.17.
  
  EGR: yes/no(4)
  
  8.17.2.1.17.1.
  
  Characteristics (cooled/uncooled, high pressure/low pressure, etc.): …
  
  8.17.2.1.18.
  
  Particulate trap: yes/no⁽⁴⁾
  
  8.17.2.1.18.1.
  
  Dimensions and capacity of the particulate trap: …
  
  8.17.2.1.18.2.
  
  Type and design of the particulate trap: …
  
  8.17.2.1.18.3.
  
  Location (place(s) and maximum/minimum distance(s) from engine: …
  
  8.17.2.1.18.4.
  
  Method or system of regeneration, description and/or drawing: …
  
  8.17.2.1.18.5.
  
  Normal operating temperature range: … K and pressure range: …kPa
  
  8.17.2.1.19.
  
  Other systems: yes/no⁽⁴⁾
  
  8.17.2.1.19.1.
  
  Description and operation: …’;
10. (x)
  
  entry 8.18., including all its sub-entries, is replaced by the following:
  
  ‘8.18.
  
  Fuel feed for diesel engines
  
  8.18.1.
  
  Feed pump
  
  8.18.1.1
  
  Pressure⁽⁷⁾ … kPa or characteristic diagram: …
  
  8.18.2.
  
  Injection system
  
  8.18.2.1.
  
  Pump
  
  8.18.2.1.1.
  
  Make(s): …
  
  8.18.2.1.2.
  
  Type(s): …
  
  8.18.2.1.3.
  
  Delivery: … and … mm³⁽⁷⁾ per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: …
  
  8.18.2.1.3.1.
  
  Method used: on engine/on pump bench⁽⁴⁾
  
  8.18.2.2.
  
  Injection advance:
  
  8.18.2.2.1.
  
  Injection advance curve⁽⁷⁾: …
  
  8.18.2.2.2.
  
  Timing⁽⁷⁾: …
  
  8.18.2.3.
  
  Injection piping:
  
  8.18.2.3.1.
  
  Length: … mm
  
  8.18.2.3.2.
  
  Internal diameter: … mm
  
  8.18.2.4.
  
  Injector(s)
  
  8.18.2.4.1.
  
  Make(s) …
  
  8.18.2.4.2.
  
  Type(s): …
  
  8.18.2.4.3.
  
  Opening pressure⁽⁷⁾: … kPa, or characteristic diagram: …
  
  8.18.2.5.
  
  Governor
  
  8.18.2.5.1.
  
  Make(s) …
  
  8.18.2.5.2.
  
  Type(s): …
  
  8.18.2.5.3.
  
  Speed at which cut-off starts under full load⁽⁷⁾: … min^–1
  
  8.18.2.5.4.
  
  Maximum no-load speed⁽⁷⁾: … min^–1
  
  8.18.2.5.5.
  
  Idling speed⁽⁷⁾: … min^–1
  
  8.18.2.6.
  
  Cold-start system
  
  8.18.2.6.1.
  
  Make(s): …
  
  8.18.2.6.2.
  
  Type(s): …
  
  8.18.2.6.3.
  
  Description: …’;
11. (xi)
  
  entry 8.19. is replaced by the following:
  
  ‘8.19.
  
  Fuel feed for petrol engines ’;
(f)

in Appendix 7 entry 25.5.2. is replaced by the following:

‘25.5.2.

Rated voltage or air pressure: … V / kPa⁽⁴⁾ ’;
(g)

in Appendix 8, the title is replaced by the following:

‘Appendix 8

Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) the installation of rear-view mirrors as a system ’

(h)

Appendix 9 is amended as follows:

(i)

entry 3.3. is replaced by the following:

‘3.3.

Axles and wheels:’;
(ii)

entry 4.1.2.1.2. is replaced by the following:

‘4.1.2.1.2.

In the case of a rigid drawbar or centre-axle R- or S-category vehicle indicate the vertical load on the front coupling point (S): … kg’;
(iii)

entries 4.1.2.2. and 4.1.2.4. are deleted;

(iv)

entry 4.1.3. is replaced by the following:

‘4.1.3.

Technically permissible towable mass(es) for T- or C-category vehicles for each chassis/ braking configuration of the R- or S-category vehicle (for R- and S-category vehicles, indicate the maximum permissible load(s) on the rear coupling point):

Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.

R- and S category vehicleBrake Drawbar Rigid drawbar Centre-axle
Unbraked^f13 … kg … kg … kg
Inertia-braked … kg … kg … kg
Hydraulic braked … kg … kg … kg
Pneumatic braked … kg … kg … kg

’

(v)

entry 4.1.4. is replaced by the following:

‘4.1.4.

Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle:

R- and S category vehicleBrake Drawbar Rigid drawbar Centre-axle
Unbraked … kg … kg … kg
Inertia-braked … kg … kg … kg
Hydraulic braked … kg … kg … kg
Pneumatic braked … kg … kg … kg

’;
(vi)
entries 4.1.5. to 4.1.5.3. are deleted;
1. (i)
  Appendix 10 is amended as follows:
  1. (i)
    
    the following entry 2.2.4. is inserted:
    
    ‘2.2.4.
    
    For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾:…’;
  2. (ii)
    
    entry 24.1. is replaced by the following:
    
    ‘24.1.
    
    Schedule describing all projected combinations of relevant vehicle electrical/electronic systems or ESAs, body styles⁽⁶⁰⁾, variations in body material , general wiring arrangements, engine variations, left-hand/right-hand drive versions and wheelbase versions:…’;

(j)
Appendix 11 is amended as follows:
1. (i)
  
  the following entry 2.2.4. is inserted:
  
  ‘2.2.4.
  
  For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
2. (ii)
  
  entry 29., including all its sub-entries, is replaced by the following:
  
  ‘29.
  
  BALLAST MASSES
  
  29.1.
  
  Detailed technical description (including photographs or drawings with dimensions) of the ballast masses and how they are mounted on the tractor:
  
  29.2.
  
  Number of sets of ballast masses: …
  
  29.2.1.
  
  Number of components on each set: Set 1: … Set 2:… Set …:…
  
  29.3.
  
  Mass of the components on each set: Set 1: ….kg Set 2: …kg Set … kg
  
  29.3.1.
  
  Total mass of each set: Set 1: …kg … Set 2: … kg Set … kg
  
  29.4.
  
  Total mass of ballast masses: …kg
  
  29.4.1.
  
  Distribution of these masses among the axles: … kg
  
  29.5.
  
  Material(s) and method of construction: …’;
(k)

Appendix 12 is amended as follows:

(i)

the following entry 2.2.4. is inserted:

‘2.2.4.

For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
(l)

Appendix 13 is amended as follows:

(i)

the following entry 2.2.4. is inserted:

‘2.2.4.

For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.
R- and S category vehicleBrake	Drawbar	Rigid drawbar	Centre-axle
Unbraked^f13	… kg	… kg	… kg
Inertia-braked	… kg	… kg	… kg
Hydraulic braked	… kg	… kg	… kg
Pneumatic braked	… kg	… kg	… kg

R- and S category vehicleBrake	Drawbar	Rigid drawbar	Centre-axle
Unbraked	… kg	… kg	… kg
Inertia-braked	… kg	… kg	… kg
Hydraulic braked	… kg	… kg	… kg
Pneumatic braked	… kg	… kg	… kg

(m)

Appendix 14 is amended as follows:

(i)

the following entry 2.2.4. is inserted:

‘2.2.4.

For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
(ii)

entry 38.1. is replaced by the following:

‘38.1.

Photographs and dimensional drawings of the mechanical coupling, its installation on the vehicle and its coupling with the device installed on the towed vehicle: …’;

(iii)

entry 38.5. is replaced by the following:

‘38.5.

Description of the mechanical coupling:

Type (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208): …
Make: …
Manufacturer’s type designation: …
Maximum horizontal load/D-Value^(4)(44): … kg/kN⁽⁴⁾
Towable mass (T) ^(4)(44): … tonnes
Maximum permissible vertical load on the coupling point (S)⁽⁴⁴⁾: … kg
Photographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.
Short technical description of the coupling device specifying the type of construction and the material used.
Type of Test Static/Dynamic ⁽⁴⁾

(EU) type-approval mark or -number of

drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars)

type-approval mark or –number of mechanical couplings that shall be attached to the ladder frame /trailer hitch support (if restricted to certain types):’;

…

’;

(n)

Appendix 15 is amended as follows:

(i)

entry 3.3. is replaced by the following:

‘3.3.

Axles and wheels:’;
(ii)

entry 4.1.2.1.2. is replaced by the following:

‘4.1.2.1.2.

In the case of a rigid drawbar or centre-axle R- or S-category vehicle indicate the vertical load on the front coupling point (S): … kg’;
(iii)

entry 4.1.2.4. is deleted;

(iv)

entry 4.1.3. is replaced by the following:

‘4.1.3.

Technically permissible towable mass(es) for T- or C-category vehicles for each chassis/ braking configuration of the R- or S-category vehicle (for R- and S-category vehicles, indicate the maximum permissible load(s) on the rear coupling point):

Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.

R- and S category vehicleBrake Drawbar Rigid drawbar Centre-axle
Unbraked^f14 … kg … kg … kg
Inertia-braked … kg … kg … kg
Hydraulic braked … kg … kg … kg
Pneumatic braked … kg … kg … kg

’

(v)

entry 4.1.4. is replaced by the following:

‘4.1.4.

Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle:

R- and S category vehicleBrake Drawbar Rigid drawbar Centre-axle
Unbraked … kg … kg … kg
Inertia-braked … kg … kg … kg
Hydraulic braked … kg … kg … kg
Pneumatic braked … kg … kg … kg

’;
(vi)

entries 4.1.5. to 4.1.5.3. are deleted;
(vii)

entry 5.1.2.2. is deleted;
(viii)

entries 6.6. and 6.7. are replaced by the following:

‘6.6.

Rated speed: … min^–1

6.7.

Maximum torque speed: … min^–1 ’;
(ix)

the following entries 7., 7.1. and 7.1.1. are inserted:

‘7.

ESSENTIAL CHARACTERISTICS OF THE ENGINE FAMILY

7.1.

Common parameters⁽⁵⁶⁾

7.1.1.

Combustion cycle: positive ignition/compression ignition⁽⁴⁾ ’;
(x)

entry 9., including all its sub-entries, is replaced by the following:

‘9.

ENERGY STORAGE DEVICE(S)⁽¹¹⁾

9.1.

Description: battery/capacitor/flywheel/generator⁽⁴⁾

9.2.

Identification number: …

9.3.

Kind of electrochemical couple: …

9.4.

Energy stored

9.4.1.

For battery, voltage: … and capacity: … Ah in 2h

9.4.2.

For capacitor: … J

9.4.3.

For flywheel/generator(4): … J

9.4.3.1.

Flywheel moment of inertia: … kg m²

9.4.3.1.1.

Additional moment of inertia if no gear is engaged: … kg m²

9.5.

Charger: on-board/external/without⁽⁴⁾ ’;

Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.
R- and S category vehicleBrake	Drawbar	Rigid drawbar	Centre-axle
Unbraked^f14	… kg	… kg	… kg
Inertia-braked	… kg	… kg	… kg
Hydraulic braked	… kg	… kg	… kg
Pneumatic braked	… kg	… kg	… kg

R- and S category vehicleBrake	Drawbar	Rigid drawbar	Centre-axle
Unbraked	… kg	… kg	… kg
Inertia-braked	… kg	… kg	… kg
Hydraulic braked	… kg	… kg	… kg
Pneumatic braked	… kg	… kg	… kg

(xi)

entry 11., including all its sub-entries, is replaced by the following:

‘11.

DRIVE-TRAIN AND CONTROL⁽¹³⁾

11.1.

Brief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train):

11.2.

Transmission

11.2.1.

Brief description and schematic drawing of gear shift system(s) and its control: …

11.2.2.

Diagram and or drawing of the transmission system: …

11.2.3.

Type of transmission: mechanical/hydraulic/electric/other⁽⁴⁾ (if other specify …)

11.2.4.

Brief description of the electrical/electronic components (if any): …

11.2.5.

Location relative to the engine: …

11.2.6.

Method of control: …

11.2.7.

Transfer box: with/without⁽⁴⁾

11.2.8.

Type of gear shift system(s)⁽²⁴⁾: …

11.3.

Clutch (if any)

11.3.1.

Brief description and schematic drawing of the clutch and its control system:

11.3.2.

Maximum torque conversion: …

11.4.

Gear ratios

Continuously variable transmission

Gear Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions) Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions) Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions) Total gear ratios Ratio (engine speed/vehicle speed) for manual transmission only

Maximum for CVT^f15

1

2

3

Minimum for CVT*

Reverse

1

…

11.5.

Differential lock

11.5.1.

Differential lock: yes/no/optional⁽⁴⁾ ’;

(xii)

entry 43.1. is replaced by the following:

‘43.1.

Brief description of the braking system(s) installed on the vehicle⁽⁵⁵⁾: …’;
(xiii)

entry 43.3. is deleted;
(xiv)

entry 43.6., including all its sub-entries, is replaced by the following:

‘43.6.

Towed vehicle braking devices

43.6.1.

Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None⁽⁴⁾

43.6.2.

Towed vehicle-brake actuating device (description, characteristics): …

43.6.3.

Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …

43.6.4.

Connections type: Single line/Two-lines/None⁽⁴⁾

43.6.4.1.

Supply pressure Hydraulic: Single line: … kPa Two lines: … kPa

43.6.4.2.

Supply pressure Pneumatic: Two lines: … kPa

43.6.5.

Presence of ISO 7638:2003 connector⁽¹⁵⁾: … yes/no⁽⁴⁾ ’;
(xv)

the following entries are added:

‘43.A

TOWED VEHICLE AXLE AND BRAKE INFORMATION DOCUMENT WITH RESPECT TO THE ALTERNATIVE TYPE I AND TYPE III PROCEDURE

43.A.1.

General

43.A.1.1.

Name and address of axle or vehicle manufacturer:

43.A.2.

Axle data

43.A.2.1.

Manufacturer (name and address): …

43.A.2.2.

Type/variant: …

43.A.2.3.

Axle identifier: ID1- …

43.A.2.4.

Test axle load (Fe): … daN

43.A.2.5.

Wheel and brake data according to the following figures 1A and 1B

43.A.3.

Brake

43.A.3.1.

General information

43.A.3.1.1.

Make:

43.A.3.1.2.

Manufacturer (name and address):

43.A.3.1.3.

Type of brake (e.g. drum / disc):

43.A.3.1.3.1.

Variant (e.g. S-cam, single wedge etc.):

43.A.3.1.4.

Brake identifier: ID2-

43.A.3.1.5.

Brake data according to the figures 2A and 2B:

43.A.3.2.

Drum brake data

43.A.3.2.1.

Brake adjustment device (external/integrated): …

43.A.3.2.2.

Declared maximum brake input torque C_max: … Nm

43.A.3.2.3.

Mechanical efficiency: η =…

43.A.3.2.4.

Declared brake input threshold torque C_0,dec: … Nm

43.A.3.2.5.

Effective length of the cam shaft: … mm

43.A.3.3.

Brake drum

43.A.3.3.1.

Max diameter of friction surface (wear limit) … mm

43.A.3.3.2.

Base material: …

43.A.3.3.3.

Declared mass: … kg

43.A.3.3.4.

Nominal mass: … kg

43.A.3.4.

Brake lining

43.A.3.4.1.

Manufacturer and address …

43.A.3.4.2.

Make …

43.A.3.4.3.

Type …

43.A.3.4.4.

Identification (type identification on lining) …

43.A.3.4.5.

Minimum thickness (wear limit) … mm

43.A.3.4.6.

Method of attaching friction material to brake shoe: …

43.A.3.4.6.1.

… Worst case of attachment (in the case of more than one):

43.A.3.5.

Disc brake data

43.A.3.5.1.

Connection type to the axle (axial, radial, integrated, etc.): …

43.A.3.5.2.

Brake adjustment device (external/integrated): …

43.A.3.5.3.

Max. actuation stroke: … mm

43.A.3.5.4.

Declared maximum input force Th_Amax: … daN

43.A.3.5.4.1

Cmax = Th_Amax · l_e : … Nm

43.A.3.5.5.

Friction radius: r_e = … mm

43.A.3.5.6.

Lever length: l_e = … mm

43.A.3.5.7.

Input/output ratio (l_e/e_e): i = …

43.A.3.5.8.

Mechanical efficiency: η = …

43.A.3.5.9.

Declared brake input threshold force Th_A0,dec: … N

43.A.3.5.9.1.

C_0,dec = Th_A0,dec · l_e : … Nm

43.A.3.5.10.

Minimum rotor thickness (wear limit): … mm

43.A.3.6.

Brake disc data …

43.A.3.6.1.

Disc type description: …

43.A.3.6.2.

Connection/mounting to the hub: …

43.A.3.6.3.

Ventilation (yes/no): …

43.A.3.6.4.

Declared mass: … kg

43.A.3.6.5.

Nominal mass: … kg

43.A.3.6.6.

Declared external diameter: … mm

43.A.3.6.7.

Minimum external diameter: … mm

43.A.3.6.8.

Inner diameter of friction ring: … mm

43.A.3.6.9.

Width of ventilation channel (if appl.): … mm

43.A.3.6.10.

Base material: …

43.A.3.7.

Brake pad data …

43.A.3.7.1.

Manufacturer and address: …

43.A.3.7.2.

Make:

43.A.3.7.3.

Type: …

43.A.3.7.4.

Identification (type identification on pad back plate): …

43.A.3.7.5.

Minimum thickness (wear limit): … mm

43.A.3.7.6.

Method of attaching friction material to pad back plate: …

43.A.3.7.6.1.

Worst case of attachment (in the case of more than one): …

Figure 1A

Figure 1B

Figure 2A

Figure 2B

xe (mm) ae (mm) he (mm) ce (mm) de (mm) ee (mm) α0e α1e be (mm) re (mm) Ae (cm2) S1e (mm) S2e (mm) S3e (mm)

’;

(o)
Appendix 19 is amended as follows:
1. (i)
  
  the following entry 2.2.4. is inserted:
  
  ‘2.2.4.
  
  For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
2. (ii)
  
  entry 46.2.1. is replaced by the following:
  
  ‘46.2.1.
  
  In the case of roll bar: foldable/not foldable⁽⁴⁾ ’;
3. (iii)
  
  entry 46.2.2., including all its sub-entries, is replaced by the following:
  
  ‘46.2.2.
  
  In the case of foldable roll bar:
  
  46.2.2.1.
  
  Folding operation: non-assisted / partially assisted / fully assisted⁽⁴⁾
  
  46.2.2.2.
  
  In case of non-assisted or partially assisted folding operation:
  
  46.2.2.2.1.
  
  Hand-operated foldable ROPS: with tools/ without tools⁽⁴⁾
  
  46.2.2.2.2.
  
  Photographs and detailed technical drawings showing the grasping area and a lateral and top view of the accessible zones. Dimensions and maximum forces for actuating the ROPS must figure on the drawings: …
  
  46.2.2.3.
  
  In case of partially assisted or fully assisted folding operation, brief description of the assistance devices as well as of their control devices, if any, and their location: …
  
  46.2.2.4.
  
  Locking mechanism: manual/automatic⁽⁴⁾
  
  46.2.2.4.1.
  
  For manual locking mechanisms, brief description of the locking mechanism and of its ergonomic design to avoid pinching or shearing hazards and to limit the force required for its operation: …
  
  46.2.2.4.2.
  
  For automatic locking mechanisms,
  
  46.2.2.4.2.1.
  
  Brief description of the locking mechanism, its control devices, if any, and their location: …
  
  46.2.2.4.2.2.
  
  Manufacturers' certificate set out in Note 2 of point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014: yes/no⁽⁴⁾ ’;
(p)

in Appendix 20, the following entry 2.2.4. is inserted:

‘2.2.4.

For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
(q)
Appendix 21 is amended as follows:
1. (i)
  
  the following entry 2.2.4. is inserted:
  
  ‘2.2.4.
  
  For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
2. (ii)
  
  entry 49.4.1. is replaced by the following:
  
  ‘49.4.1.
  
  Position of the driving seat: left/right/centre⁽⁴⁾ ’;

(r)

Appendix 22 is amended as follows:

(i)

the following entry 2.2.4. is inserted:

‘2.2.4.

For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;

(ii)

entry 54.3. is replaced by the following:

‘54.3.

Number and position of safety belts and seats on which they can be used, please fill out table below:

Safety belt configuration and associated information

L = left, C = centre, R = right

Complete EU type-approval mark / ECE type-approval mark Variant, if applicable Belt adjustment device for height (indicate yes/no/optional)
Driver's seat L
C
R

Passenger seat

1
L
C
R

Passenger seat

…
L
C
R

’;

(s)

in Appendix 23, the following entry 2.2.4. is inserted:

‘2.2.4.

For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available)⁽¹⁹⁾: …’;
(r)
Appendix 24 is replaced by the following:

‘Appendix 24

Manufacturer’s declaration on anti-tampering of powertrain and speed-limitation device

Manufacturer’s declaration on anti-tampering of powertrain and speed-limitation device

A duly-completed version of this statement shall be included in the information folder.

The undersigned: [… (full name and position)]

2.3.

Company name and address of manufacturer: …

2.3.2.

Name and address of the manufacturer’s authorised representative (if any)^f16: …

Hereby declares that:

2.1.

Make(s) (trade name(s) of manufacturer: …
1. 2.4.1.
  
  Type^f17: …
2. 2.4.2.
  
  Variant(s): …
3. 2.4.3.
  
  Version(s): …
4. 2.4.4
  
  Commercial name(s) (if available): …
5. 2.4.5.
  
  Category, subcategory and speed index of vehicle^f18: …
Will not market interchangeable components which could involve an increase in the propulsion performance of the vehicle variant

Place: … Date: …

Signature: … Name and position in the company: …

Explanatory notes relating to Appendix 24

(Footnote markers, footnotes and explanatory notes not to be stated on the Manufacturer’s declaration)
(s)
the explanatory notes relating to the information document are amended as follows:
1. (i)
  
  explanatory note (9) is replaced by the following:
  
  ‘(9)
  
  Indicate fuel type by the following codes:
  
  P
  
  petrol
  
  B5
  
  diesel
  
  E5
  
  petrol E5
  
  M
  
  mixture (for two stroke engines)
  
  O
  
  other.’
2. (ii)
  
  the following explanatory note (11) is inserted:
  
  ‘(11)
  
  Excluding SLI batteries that supply electric energy for starting, lighting and ignition.’
3. (iii)
  
  explanatory note (14) is replaced by the following:
  
  ‘(14)
  
  ‘A’
  
  for a three-point belt;
  
  ‘B’
  
  for a lap belt;
  
  ‘S’
  
  for special types of belt (in this case provide specific information on the nature of these types under observation in entry 53.4.1.);
  
  ‘Ar’, ‘Br’ or‘Sr’
  
  for a belt incorporating an inertia reel retractor;
  
  ‘Are’, ‘Bre’ and ‘Sre’
  
  for a belt equipped with an inertia reel retractor and an energy-absorption device on at least one anchorage.’
4. (iv)
  
  the following explanatory notes (15) and (16) are inserted:
  
  ‘(15)
  
  Only applicable to T- and C-category vehicles authorized to tow R- or S-category vehicles if fitted with a hydraulic energy storage device.
  
  ‘(16)
  
  Indicate the maximum towable mass on the lower link arms of the rear three-point lifting mechanism or the rear three-point lifting mechanism itself, as declared by the manufacturer.’’
5. (v)
  
  explanatory note (24) is replaced by the following:
  
  ‘(24)
  
  Indicate the type of gear shift system(s) by the following codes:
  
  A
  
  automatic
  
  M1
  
  manual
  
  M2
  
  manual automated
  
  C
  
  continuous variable transmission (CVT)
  
  W
  
  wheel-hub engine
  
  O
  
  other (indicate…)’;
6. (vi)
  
  explanatory note (26) is replaced by the following:
  
  ‘(26)
  
  Indicate the layout of the cylinders by following codes:
  
  LI
  
  in line
  
  V
  
  in V
  
  O
  
  opposed-cylinder engine
  
  S
  
  single-cylinder engine
  
  R
  
  rotatory piston engine. ’;
7. (vii)
  
  explanatory note (48) is replaced by the following:
  
  ‘(48)
  
  For R- and S-category vehicles indicate the overhang of the front coupling point. ’;
8. (viii)
  
  explanatory note (49) is replaced by the following:
  
  ‘(49)
  
  For engines indicate the information relative to the engine type or the engine family type, as applicable without the type-approval extension number.’
9. (ix)
  
  explanatory note (52) is replaced by the following:
  
  ‘(52)
  
  When the tractor is fitted with different optional seats or has a reversible driver’s position (reversible seat and steering wheel), the dimensions in relation to the seat index points (SIP 1, SIP 2, etc.) shall be measured for each case.’

Annotations

Footnotes

f1: Commission Delegated Regulation (EU) No 1322/2014 of 19 September 2014 supplementing and amending Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle construction and general requirements for the approval of agricultural and forestry vehicles (OJ L 364, 18.12.2014, p. 1).’
f2: Commission Delegated Regulation (EU) 2015/96 of 1 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council as regards environmental and propulsion unit performance requirements of agricultural and forestry vehicles (OJ L 16, 23.1.2015, p. 1).
f3: Commission Delegated Regulation (EU) 2015/68 of 15 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle braking requirements for the approval of agricultural and forestry vehicles (OJ L 17, 23.1.2015, p. 1).
f4: According to the tyre specification.
f5: Load transmitted to the reference centre of the coupling under static conditions, irrespective to the coupling device; if the maximum permissible vertical load on the coupling point depending on the coupling is indicated in this table, expand the table at the right side and indicate the identification of the coupling device in the header of the column; for R- or S-category vehicles this column(s) concerns the rear coupling devices if there is such a device.
f6: Value to be provided only if the maximum permissible vertical load on the coupling point is lower than indicated in entries 38.3 and 38.4
f7: Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.
f8: Continuously variable transmission
f9: x

yes

–

no or not separately available

o

optional.
f10: d

directly on control, indicator or tell-tale

c

in close vicinity.
f11: x

yes

–

no or not separately available

o

optional.
f12: d

directly on control, indicator or tell-tale

c

in close vicinity.
f13: Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.
f14: Calculated using the partially laden condition defined by the tractor manufacturer in agreement with the technical service set out in point 3.1.1.2 of Annex II to Commission Delegated Regulation (EU) 2015/68.
f15: Continuously variable transmission
f16: Delete the entry if not applicable.
f17: Indicate the alphanumeric code Type-Variant-Version or “TVV” allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I to this Regulation. For the identification of variant and versions it may be employed the matrix set out in point 2.2 of Part B of Annex I to this Regulation.
f18: Classified according to Article 4 of Regulation (EU) No 167/2013, the coding shall be indicated, e.g. “T4.3a” for a low-clearance tractor with a maximum design speed below or equal to 40 km/h.’

Type (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	…
Make:	…
Manufacturer’s type designation:	…
Maximum horizontal load/D-Value^(4)(44):	… kg/kN⁽⁴⁾
Towable mass (T) ^(4)(44):	… tonnes
Maximum permissible vertical load on the coupling point (S)⁽⁴⁴⁾:	… kg
Photographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.
Short technical description of the coupling device specifying the type of construction and the material used.
Type of Test	Static/Dynamic ⁽⁴⁾
(EU) type-approval mark or -number of drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars) type-approval mark or –number of mechanical couplings that shall be attached to the ladder frame /trailer hitch support (if restricted to certain types):	…

			Complete EU type-approval mark / ECE type-approval mark	Variant, if applicable	Belt adjustment device for height (indicate yes/no/optional)
L = left, C = centre, R = right
Driver's seat		L
		C
		R
Passenger seat 1		L
		C
		R
Passenger seat …		L
		C
		R

Symbol No	Device	Control / indicator available^f9	Identified by symbol	Where^f10	Tell-tale available	Identified by symbol	Where
x yes – no or not separately available o optional.
d directly on control, indicator or tell-tale c in close vicinity.
1	Dipped-beam head lamps
2	Main-beam head lamps
3	Position (side) lamps
4	Front fog lamps
5	Rear fog lamp
6	Headlamp levelling device
7	Parking lamps
8	Direction indicators
9	Hazard warning
10	Windscreen wiper
11	Windscreen washer
12	Windscreen wiper and washer
13	Headlamp cleaning device
14	Windscreen demisting and defrosting
15	Rear window demisting and defrosting
16	Ventilating fan
17	Diesel pre-heat
18	Choke
19	Brake failure
20	Fuel level
21	Battery charging condition
22	Engine coolant temperature
23	Malfunction indicator light (MI)

Symbol No	Device	Control / indicator available^f11	Identified by symbol	Where^f12	Tell-tale available	Identified by symbol	Where
x yes – no or not separately available o optional.
d directly on control, indicator or tell-tale c in close vicinity.
1	Parking brake
2	Rear window wiper
3	Rear window washer
4	Rear window wiper and washer
5	Intermittent windscreen wiper
6	Audible warning device
7	Hood
8	Seat belt
9	Engine oil pressure
10	Unleaded petrol
11	…
12	….