Council Regulation (EU) 2017/1134 of 20 June 2017 amending Regulation (EU) No 1387/2013 suspending the autonomous Common Customs Tariff duties on certain agricultural and industrial products

*ex 2905 11 00

ex 2905 19 00

20

35

Allyl methacrylate (CAS RN 96-05-9) and its' isomers with a purity by weight of 98 % or more and containing at least:

• 0,01 % or more but not more than 0,02 % of Allyl alcohol (CAS RN 107-18-6),

• 0,01 % or more but not more than 0,1 % of Methacrylic acid (CAS RN 79-41-4), and

• 0,5 % or more but not more than 1 % of 4-Methoxyphenol (CAS RN 150-76-5)

*ex 2920 29 00

ex 2920 90 70

50

50

*ex 2920 29 00

ex 2920 90 70

60

40

*ex 2932 14 00

ex 2940 00 00

10

40

*ex 2933 59 95

ex 2933 99 80

88

51

Preparations based on Colourant Reactive Black 5 (CAS RN 17095-24-8) with a content thereof of 60 % or more but not more than 75 % by weight, and including one or more of the following:

• Colourant Reactive Yellow 201 (CAS RN 27624-67-5),

• 1-Naphthalenesulphonicacid,4-amino-3-[[4-[[2-(sulphooxy)ethyl]sulphonyl]phenyl]azo]-, disodium salt (CAS RN 250688-43-8), or

• 3,5-diamino-4-[[4-[[2-(sulphooxy)ethyl]sulphonyl]fenyl]azo]-2-[[2-sulfo-4-[[2-(sulphooxy)ethyl]sulfonyl]phenyl]azobenzoic acid sodium salt (CAS RN 906532-68-1)

Disposable cartridge ink, containing by weight:

• 1 % or more, but not more than 10 % of amorphous silicon dioxide or

• 3,8 % or more of dye C.I. Solvent Black 7 in organic solvents

for use in the marking of integrated circuits (²)

*ex 3506 91 10

ex 3506 91 90

50

50

Preparation containing by weight:

• 15 % or more but not more than 60 % of styrene butadiene copolymers or styrene isoprene copolymers and

• 10 % or more but not more than 30 % of pinene polymers or pentadiene copolymers

dissolved in:

• Methyl ethyl ketone (CAS RN 78-93-3)

• Heptane (CAS RN 142-82-5), and

• Toluene (CAS RN 108-88-3) or light aliphatic solvent naphta (CAS RN 64742-89-8)

Dispersing agent and oxidation inhibitor containing:

• o-amino polyisobutylenephenol (CAS RN 78330-13-9),

• more than 30 % by weight but not more than 50 % by weight of mineral oils,

used in the manufacture of blends of additives for lubricating oils (²)

Additives containing:

• a polyisobutylene succinimide based mixture, and

• more than 30 % but not more than 50 % by weight of mineral oils,

having a total base number of more than 40, for use in the manufacture of lubricating oils (²)

Corrosion inhibitor containing:

• polyisobutenyl succinic acid and

• more than 5 % and not more than 20 % by weight of mineral oils

for use in the manufacture of blends of additives for fuels (²)

Catalyst:

• containing molybdenum oxide and other metal oxides in a silicon dioxide matrix,

• in the form of hollow cylindrical solids of a length of 4 mm or more but not more than 12 mm

for use in the manufacture of acrylic acid (²)

Preparation containing by weight:

• 25 % or more but not more than 50 % of diethyl carbonate (CAS RN 105-58-8)

• 25 % or more but not more than 50 % of ethylene carbonate (CAS RN 96-49-1)

• 10 % or more but not more than 20 % of lithium hexafluorophosphate (CAS RN 21324-40-3)

• 5 % or more but not more than 10 % of ethyl methyl carbonate (CAS RN 623-53-0)

• 1 % or more but not more than 2 % of vinylene carbonate (CAS RN 872-36-6)

• 1 % or more but not more than 2 % of 4-fluoro-1,3-dioxolane-2-one (CAS RN 114435-02-8)

• Not more than 1 % of 1,5,2,4-Dioxadithiane 2,2,4,4-tetraoxide (CAS RN 99591-74-9)

Aqueous solution of caesium formate and potassium formate containing by weight:

• 1 % or more but not more than 84 % of caesium formate (CAS RN 3495-36-1),

• 1 % or more but not more than 76 % of potassium formate (CAS RN 590-24-1), and

• whether or not containing not more than 9 % of additives

Preparation containing by weight:

• 80 % or more but not more than 92 % of Bisphenol-A bis(diphenyl phosphate) (CAS RN 5945-33-5)

• 7 % or more but not more than 20 % oligomers of Bisphenol-A bis(diphenyl phosphate) and

• not more than 1 % triphenyl phosphate (CAS RN 115-86-6)

Sodium hydrogen 3-aminonaphthalene-1,5-disulphonate (CAS RN 4681-22-5) containing by weight:

• not more than 20 % of disodium sulphate, and

• not more than 10 % of sodium chloride

Powder containing by weight:

• 28 % or more but not more than 51 % of talc (CAS RN 14807-96-6)

• 30,5 % or more but not more than 48 % of silicon dioxide (quartz) (CAS RN 14808-60-7)

• 17 % or more but not more than 26 % of aluminium oxide (CAS RN 1344-28-1)

Mixture with a non-stoichiometric composition:

• with a crystalline structure,

• with a content of fused magnesia-alumina spinel and with admixtures of silicate phases and aluminates, at least 75 % by weight of which consists of fractions with a grain size of 1-3 mm and at most 25 % consists of fractions with a grain size of 0-1 mm

Mixture consisting of:

• 64 % or more, but not more than 74 % by weight of amorphous silica (CAS RN 7631-86-9)

• 25 % or more, but not more than 35 % by weight of butanone (CAS RN 78-93-3) and

• not more than 1 % by weight of 3-(2,3-epoxypropoxy)propyltrimethoxysilane (CAS RN 2530-83-8)

*ex 3901 10 10

ex 3901 90 80

20

50

High flow linear low density polyethylene-1-butene/LLDPE (CAS RN 25087-34-7) in form of powder, with

• a melt flow rate (MFR 190 °C/2,16 kg) of 16 g/10 min or more, but not more than 24 g/10 min and

• a density (ASTM D 1505) of 0,922 g/cm³ or more, but not more than 0,926 g/cm³ and

• a vicat softening temperature of min. 94 °C

Polyacrylamide powder having an average particle size of less than 2 microns and a melting point of more than 260 °C, containing by weight:

• 75 % or more but not more than 85 % of polyacrylamide and

• 15 % or more but not more than 25 % of polyethylene glycol

Preparation containing by weight:

• 55 % or more but not more than 65 % of vinyl terminated polydimethylsiloxane (CAS RN 68083-19-2),

• 30 % or more but not more than 40 % of dimethylvinylated and trimethylated silica (CAS RN 68988-89-6), and

• 1 % or more but not more than 5 % of silicic acid, sodium salt, reaction products with chlorotrimethylsilane and isopropyl alcohol (CAS RN 68988-56-7)

Tetrafluoroethylene film, put up in rolls, with:

• a thickness of 50 μm,

• a melting point of 260 °C, and

• a specific gravity of 1,75 (ASTM D792)

for use in the manufacture of semiconductor devices (²)

Porous membrane of polytetrafluorethylene (PTFE) laminated to a polyester spunbonded non-woven cloth with:

• a total thickness of more than 0,05 mm but not more than 0,20 mm,

• a water entry pressure between 5 and 200 kPa according to ISO 811, and

• an air permeability of 0,08 cm³/cm²/s or more according to ISO 5636-5

Photomask or wafer compacts:

• consisting of antistatic materials or blended thermoplastics proving special electrostatic discharge (ESD) and outgassing properties,

• having non porous, abrasion resistant or impact resistant surface properties,

• fitted with a specially designed retainer system that protects the photomask or wafers from surface or cosmetic damage and

• with or without a gasket seal,

of a kind used in the photolithography or other semiconductor production to house photomasks or wafers

*ex 3926 30 00

ex 8708 29 10

ex 8708 29 90

10

10

10

ex 3926 90 97

ex 8512 90 90

77

10

Air intake hose for air supply to the combustion part of the engine comprising at least:

• one flexible rubber hose,

• one plastic hose, and

• metal clips,

• whether or not a resonator

for use in the manufacture of goods of Chapter 87 (²)

*ex 5911 90 99

ex 8421 99 90

30

92

*ex 7410 11 00

ex 8507 90 80

ex 8545 90 90

10

60

30

Roll of laminate foil of graphite and copper, with:

• a width of 610 mm or more but not more than 620 mm, and

• a diameter of 690 mm or more but not more than 710 mm,

for use in the manufacture of lithium-ion electric rechargeable batteries (²)

*ex 7607 11 90

ex 7607 11 90

47

57

Aluminium foil in rolls:

• having a purity of 99,99 % by weight,

• of a thickness of 0,021 mm or more but not more than 0,2 mm,

• with a width of 500 mm,

• with a surface oxide layer by 3 to 4 nm thick,

• and with a cubic texture of more than 95 %

*ex 7607 19 90

ex 8507 90 80

10

80

Sheet in the form of a roll consisting of a laminate of lithium and manganese bonded to aluminium, with:

• a width of 595 mm or more but not more than 605 mm, and

• a diameter of 690 mm or more but not more than 710 mm,

for use in the manufacture of cathodes for lithium-ion electric rechargeable batteries (²)

*ex 7616 99 10

ex 8708 99 10

ex 8708 99 97

30

60

50

Aluminium engine bracket, with dimensions of:

• height of more than 10 mm but not more than 200 mm

• width of more than 10 mm but not more than 200 mm

• length of more than 10 mm but not more than 200 mm

equipped with at least two fixing holes, made of aluminium alloys ENAC-46100 or ENAC-42100 (based on the norm EN:1706) with following characteristics:

• internal porosity not more than 1 mm;

• outer porosity not more than 2 mm;

• Rockwell hardness HRB 10 or more

of a kind used in the production of suspensions systems for engines in motor vehicles

*ex 8301 60 00

ex 8413 91 00

ex 8419 90 85

ex 8438 90 00

ex 8468 90 00

ex 8476 90 90

ex 8479 90 70

ex 8481 90 00

ex 8503 00 99

ex 8515 90 80

ex 8536 90 95

ex 8537 10 98

ex 8708 91 20

ex 8708 91 99

ex 8708 99 10

ex 8708 99 97

20

40

30

20

20

20

83

30

70

30

95

70

10

20

50

40

Keypads of silicone or plastic,

• whether or not with parts of metal, plastic, glass fibre reinforced epoxide resin or wood,

• whether or not printed or surface treated,

• whether or not with electrical conducting elements,

• whether or not with keypads foil glued on the keyboard,

• whether or not with protective foil,

• single or multilayer

*ex 8409 91 00

ex 8409 99 00

30

50

Exhaust manifold with spiral-shaped gas turbine turbocharger component with:

• a heat-resistance of not more than 1 050 °C, and

• a turbine wheel hole diameter of 30 mm or more, but not more than 110 mm

Plastic or aluminum cylinder head cover with:

• a camshaft position sensor (CMPS),

• metal brackets for mounting on an engine, and

• two or more gaskets,

for use in the manufacture of engines of motor vehicles (²)

Spiral-shaped gas turbine turbocharger component:

• with a heat-resistance of not more than 1 050 °C, and

• with a turbine wheel hole diameter of 30 mm or more, but not more than 110 mm

Single-cylinder radial-piston high pressure pump for gasoline direct injection with:

• an operating pressure of 200 bar or more, but not more than 350 bar,

• a flow control, and

• a pressure relief valve,

for use in the manufacture of engines of motor vehicles (²)

DC Motor:

• with a speed rotation of not more than 7 000 rpm (without load),

• with a nominal voltage of 12 V (± 4 V),

• with a maximum power of 13,78 W (at 3,09 A),

• with a specified temperature range from – 40 °C to 160 °C,

• with a gear connection,

• with a mechanical attachment interface,

• with 2 electrical connections,

• with a maximum torque of 100 Nm

DC Motor:

• with a speed rotation of not more than 6 500 rpm (without load),

• with a nominal voltage of 12 V (± 4 V),

• with a maximal power below than 20 W,

• with a specified temperature range from – 40 °C to 160 °C,

• with a worm gear drive,

• with a mechanical attachment interface,

• with 2 electrical connections,

• with a maximum torque of 75 Nm

Electric turbocharger actuator, with:

• a DC motor,

• an integrated gear mechanism,

• a (pulling)force of 200 N or more at a minimum of 140 °C elevated ambient temperature,

• a (pulling) force of 250 N or more in each position of its stroke,

• an effective stroke of 15 mm or more but not more than 25 mm,

• with or without an on-board diagnostics interface

Direct current to direct current converter

• without housing or

• with housing with connection pins, connection studs, screw connectors, unprotected line connections, connection elements which allow the mounting to a printed circuit board by soldering or any other technology, or other wiring connections requiring further processing

Solenoid coil with:

• a rated power of more than 10 W but not more than 15 W,

• an insulation resistance of 100 M Ohms or more,

• a DC resistance of not more than 34,8 Ohm (± 10 %) at 20 °C,

• a rated current of not more than 1,22 A,

• a rated voltage of not more than 25 V

Permanent magnets consisting of an alloy of neodymium, iron and boron, either in the shape of a rectangle, whether or not rounded, with a rectangular or a trapezoidal section having

• a length of not more than 140 mm,

• a width of not more than 90 mm, and

• a thickness of not more than 55 mm,

or in the shape of curved rectangle (tile type) having

• a length of not more than 75 mm,

• a width of not more than 40 mm,

• a thickness of not more than 7 mm, and

• a radius of curvature of more than 86 mm but not more than 241 mm

or in the shape of a disc with a diameter of not more than 90 mm, whether or not containing a hole in the centre

A quarter sleeve intended to become permanent magnet after magnetization,

• consisting of at least neodymium, iron and boron,

• with a width of 9,1 mm or more but not more than 10,5 mm,

• with a length of 20 mm or more but not more than 30,1 mm,

of a kind used on rotors for the manufacture of fuel pumps

Cut plate of nickel-plated copper foil, with:

• a width of 70 mm (± 5 mm),

• a thickness of 0,4 mm (± 0,2 mm),

• a length of not more than 55 mm,

for use in the manufacture of lithium-ion electric rechargeable batteries (²)

Audio power amplifier with:

• an output power of 50 W,

• an operating voltage of more than 9 V but not more than 16 V,

• an electrical impedance of not more than 4 Ohm,

• a sensitivity of more than 80 dB

• in a metal housing

for use in the manufacture of motor vehicles (²)

*ex 8522 90 80

ex 8529 90 92

30

57

*ex 8529 90 65

ex 8529 90 92

65

53

LCD modules with:

• a diagonal measurement of the screen of 14,5 cm or more but not more than 25,5 cm,

• a LED backlight,

• a printed circuit board with EPROM (Erasable Programmable Read-only Memory), microcontroller, timing controller, LIN (Local Interconnect Network)bus or APIX2 (Automative Pixel Link) driver module and other active and passive components,

• 6 to 8 pin plug for power supply and 2 to 4- pin LVDS (Low-voltage differential signalling) or APIX2 interface,

• whether or not in a housing,

for permanent incorporation or permanent mounting into motor vehicles of Chapter 87 (²)

LCD module

• with a diagonal measurement of the screen of 14,5 cm or more but not more than 38,5 cm,

• with or without a touch screen,

• with an LED backlight,

• with a printed circuit board with EEPROM, microcontroller, LVDS receiver and other active and passive components,

• with a plug for power supply and CAN and LVDS interfaces,

• with or without electronic components for dynamic adjustments of colour,

• in a housing, with or without mechanical, touch-sensitive or contactless control functions and with or without active cooling system,

suitable for installation in motor vehicles of Chapter 87 (²)

Colour LCD display panel for LCD monitors of heading 8528:

• with a diagonal measurement of the screen of 14,48 cm or more but not more than 31,24 cm,

• with or without a touch screen,

• with backlight, micro-controller,

• with a CAN (Controller area network)-controller with one or more LVDS (Low-voltage differential signalling) interfaces and one or more CAN/power supply sockets or with an APIX (Automotive Pixel Link) controller with APIX interface,

• in a housing with or without a heat sink at the back of the housing,

• without a signal-processing module,

• whether or not with haptic and acoustical feedback,

for use in the manufacture of vehicles of Chapter 87 (²)

*ex 8536 90 95

ex 8544 49 93

94

10

Lever for control module under the steering wheel:

• with one or more single or multi-positional electrical switches (push-button, rotary or other),

• whether or not equipped with printed circuit boards and electrical cables,

• for a voltage of 9 V or more but not more than 16 V,

of a kind used in the manufacture of motor vehicles of Chapter 87

Control unit for keyless access to vehicle and vehicle starting, with electrical switching apparatus, in a plastic housing, for a voltage of 12 V, whether or not with:

• an antenna,

• a connector,

• a metal holder,

for use in the manufacture of goods of Chapter 87 (²)

Laminated electrochromic film consisting of:

• two outer layers of polyester,

• a middle layer of acrylic polymer and silicone, and

• two electric connection terminals

12-wire connecting cable containing two connectors

• of a voltage of 5 V,

• with a length of not more than 300 mm

for use in the manufacture of goods of Chapter 87 (²)

ex 8708 10 10

ex 8708 10 90

10

10

*ex 8708 30 10

ex 8708 30 91

ex 8708 30 99

20

60

10

Motor powered brake actuation unit

• with a rating of 13,5 V (± 0,5 V) and

• a ball screw mechanism to control brake fluid pressure in the master cylinder

for use in the manufacture of electric motor vehicles (²)

*ex 8708 30 10

ex 8708 30 91

40

30

*ex 8708 30 10

ex 8708 30 91

50

10

Drum type parking brake:

• operating within the service brake disk,

• with a diameter of 170 mm or more but not more than 195 mm

for use in the manufacture of motor vehicles (²)

*ex 8708 30 10

ex 8708 30 91

60

20

*ex 8708 30 10

ex 8708 30 91

70

40

*ex 8708 40 20

ex 8708 40 50

20

10

Automatic hydrodynamic gearbox

• with a hydraulic torque converter,

• without transfer box and cardan shaft,

• whether or not with front differential,

for use in the manufacture of motor vehicles of Chapter 87 (²)

*ex 8708 50 20

ex 8708 50 55

10

10

*ex 8708 50 20

ex 8708 50 99

20

10

Transmission shaft in carbon fibre reinforced plastics consisting of a unique piece without any joint in the middle

• of a length of 1 m or more but not more than 2 m,

• of a weight of 6 kg or more but not more than 9 kg

*ex 8708 50 20

ex 8708 50 99

ex 8708 99 10

ex 8708 99 97

30

20

20

70

Single input, dual output gearcase (transmission) in a cast aluminum housing, with overall dimensions of 273 mm (width) × 131 mm (height) × 187 mm (length), comprising at least:

• two electro-magnetic one direction clutches, working in opposite sides,

• an input shaft with an outer diameter of 24 mm (± 1 mm), ended with 22 teeth spline, and

• a coaxial output bushing with an inner diameter of 22 mm (± 1 mm), ended with 22 teeth spline

for use in the manufacture of all-terrain vehicles or utility task vehicles (²)

*ex 8708 80 20

ex 8708 80 35

10

10

Upper strut insulator containing

• a metal holder with three mounting screws, and

• a rubber bump

of a kind used in the manufacture of goods of Chapter 87

*ex 8708 80 20

ex 8708 80 91

20

10

*ex 8708 80 20

ex 8708 80 91

30

20

*ex 8708 91 20

ex 8708 91 35

20

10

*ex 8708 91 20

ex 8708 91 99

30

30

Aluminium alloy inlet or outlet air tank manufactured to standard EN AC 42100 with:

• an insulating area flatness of not more than 0,1 mm,

• a permissible particle quantity of 0,3 mg per tank,

• a distance between pores of 2 mm or more,

• pore sizes of not more than 0,4 mm, and

• not more than 3 pores larger than 0,2 mm

of a kind used in heat exchangers for car cooling systems

*ex 8708 94 20

ex 8708 94 35

10

20

*ex 8708 95 10

ex 8708 95 99

40

10

Front passenger airbag composed of:

• a metal housing with at least six mounting brackets,

• an embedded safety cushion,

• a cartridge filled with compressed gas

of a kind used in the manufacture of goods of Chapter 87

ex 8708 99 10

ex 8708 99 97

30

15

ex 8708 99 10

ex 8708 99 97

40

25

*ex 8714 91 30

ex 8714 91 30

ex 8714 91 30

25

35

72

Electronic semiconductor micro-mirror in a housing suitable for the automatic printing of conductor boards, mainly consisting of a combination of:

• one or more monolithic application-specific integrated circuits (ASIC),

• one or more microelectromechanical mirrors (MEMS) manufactured with semiconductor technology, with mechanical components arranged in three-dimensional structures on the semiconductor material

of a kind used for incorporation into products of Chapters 84 to 90 and 95