OpenLegislation

Division 4.3.5.2.1 Definition of target engine speed setpoints

United Kingdom

Original text. Later amendments are not shown.

The 10 target engine speed setpoints are defined by 4 base target engine speed setpoints and 6 additional target engine speed setpoints.

The engine speeds nidle, nlo, npref, n95h and nhi shall be determined from the engine full load curve of the CO2-parent engine of the engine CO2-family defined in accordance with Appendix 3 to this Annex and recorded in accordance with paragraph 4.3.1 by applying the definitions of characteristic engine speeds in accordance with paragraph 7.4.6. of Annex 4 to UN/ECE Regulation 49 Rev.06.

The engine speed n57 shall be determined by the following equation:

n57 = 0,565 × (0,45 × nlo + 0,45 × npref + 0,1 × nhi – nidle) × 2,0327 + nidle

The 4 base target engine speed setpoints are defined as follows:

  1. (1)

    Base engine speed 1: nidle

  2. (2)

    Base engine speed 2: nA = n57 – 0,05 × (n95h – nidle)

  3. (3)

    Base engine speed 3: nB = n57 + 0,08 × (n95h – nidle)

  4. (4)

    Base engine speed 4: n95h

The potential distances between the speed setpoints shall be determined by the following equations:

  1. (1)

    dnidleA_44 = (nA – nidle) / 4

  2. (2)

    dnB95h_44 = (n95h – nB) / 4

  3. (3)

    dnidleA_35 = (nA – nidle) / 3

  4. (4)

    dnB95h_35 = (n95h – nB) / 5

  5. (5)

    dnidleA_53 = (nA – nidle) / 5

  6. (6)

    dnB95h_53 = (n95h – nB) / 3

The absolute values of potential deviations between the two sections shall be determined by the following equations:

  1. (1)

    dn44 = ABS(dnidleA_44 – dnB95h_44)

  2. (2)

    dn35 = ABS(dnidleA_35 – dnB95h_35)

  3. (3)

    dn53 = ABS(dnidleA_53 – dnB95h_53)

F1The 6 additional target engine speed setpoints shall be determined in accordance with the following provisions:

  1. (1)

    If dn 44 is smaller than or equal to (dn 35  + 5) and also smaller than or equal to (dn 53  + 5), the 6 additional target engine speeds shall be determined by dividing each of the two ranges, one from n idle to n A and the other from n B to n 95h , into 4 equidistant sections.

  2. (2)

    If (dn 35  + 5) is smaller than dn 44 and also dn 35 is smaller than dn 53 , the 6 additional target engine speeds shall be determined by dividing the range from n idle to n A into 3 equidistant sections and the range from n B to n 95h , into 5 equidistant sections.

  3. (3)

    If (dn 53  + 5) is smaller than dn 44 and also dn 53 is smaller than dn 35 , the 6 additional target engine speeds shall be determined by dividing the range from n idle to n A into 5 equidistant sections and the range from n B to n 95h , into 3 equidistant sections.

Figure 1 exemplarily illustrates the definition of the target engine speed setpoints according to subpoint (1) above.

Figure 1

Definition of speed setpoints

Annotations

Textual amendments

F1

Substituted by Commission Regulation (EU) 2019/318 of 19 February 2019 amending Regulation (EU) 2017/2400 and Directive 2007/46/EC of the European Parliament and of the Council as regards the determination of the CO2 emissions and fuel consumption of heavy-duty vehicles (Text with EEA relevance).