Paragraph 2 E1

England, Wales and Scotland

(1)

A manufacturer must lodge an application for F1Type examination (Module B) with a single F2approved body of the manufacturer's choice.

(2)

The application must include—

(a)

the name and address of the manufacturer and, if the application is lodged by an authorised representative, the name and address of the authorised representative;

(b)

a written declaration that the same application has not been lodged with any other approved body;

(c)

the technical documentation;

(d)

where applicable, the prototype vessels (and any further prototype vessels requested by the approved body if needed for carrying out the test programme) representative of the production envisaged;

(e)

the supporting evidence for the adequacy of the technical design solution; this supporting evidence must—

(i)

mention any documents that have been used, in particular where the relevant F3designated standards have not been applied in full;

(ii)

include, where necessary, the results of tests carried out in accordance with other technical specifications by the appropriate laboratory of the manufacturer, or by another testing laboratory on the manufacturer's behalf and under his responsibility.

Annotations

Textual amendments

F1: Word in Sch. 2 substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 21 para. 40(e) (with Sch. 21 para. 37) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F2: Words in Sch. 2 substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 21 para. 40(c) (with Sch. 21 para. 37) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)
F3: Word in Sch. 2 para. 2(2)(e)(i) substituted (E.W.S.) (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 21 para. 40(f) (with Sch. 21 para. 37) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)

Extent

E1: This version of this provision extends to England and Wales and Scotland only; a separate version has been created for Northern Ireland only

Notes on the whole SI

Textual amendments

F1: S.I. 1989/1327.
F2: 1972 c.68. Section 2(2) was amended by section 27(1)(a) of the Legislative and Regulatory Reform Act 2006 (c.51) and by Part 1 of the Schedule to the European Union (Amendment) Act 2008 (c.7). The enabling powers of section 2(2) were extended by virtue of the amendment of section 1(2) by section 1 of the European Economic Area Act 1993 (c.51).
F3: Paragraph 1A of Schedule 2 was inserted by section 28 of the Legislative and Regulatory Reform Act 2006 and amended by Part 1 of the Schedule to the European Union (Amendment) Act 2008.

Notes on Part 1

Textual amendments

F1: Word in Sch. 2 heading omitted (E.W.S.) (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 21 para. 40(a) (with Sch. 21 para. 37) (as amended by S.I. 2020/676, regs. 1(1), 2); 2020 c. 1, Sch. 5 para. 1(1)