Paragraph 17 Commission Regulation (EU) No 617/2013I1

United Kingdom

(1)

Commission Regulation (EU) No 617/2013 of 26 June 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for computers and computer servers is amended as follows.

(2)

In Article 2 (definitions), at the beginning, for “The following definitions shall apply:”, substitute—

“The definitions set out in the Ecodesign for Energy-Related Products Regulations 2010 apply; and for any term that is not defined in those Regulations, the definitions set out in Directive 2009/125/EC of the European Parliament and of the Council of 21 October 2009 establishing a framework for the setting of ecodesign requirements for energy-related products, as it had effect immediately before F1IP completion day, apply. The following definitions also apply—”.

(3)

For Article 6 (conformity assessment), substitute—

“For the purposes of regulation 4(2)(a) of the Ecodesign for Energy-Related Products Regulations 2010, the procedure for assessing whether an energy-related product complies with this implementing measure is the internal design control system set out in Part 1 of Schedule 1A to the Ecodesign for Energy-Related Products Regulations 2010 or the management system for assessing conformity set out in Part 2 of Schedule 1A to those Regulations.”.

(4)

In Article 7 (market surveillance and verification procedure), for “Directive 2009/125/EC”, substitute “ the Ecodesign for Energy-Related Products Regulations 2010 ”.

(5)

Omit Article 9 (revision).

(6)

At the end of Article 10 (entry into force and application), omit “This Regulation shall be binding in its entirety and directly applicable in all Member States.”.

(7)

Annex 3 (measurements by market surveillance authorities and product compliance verification by market surveillance authorities) is amended as follows—

(a)

in each instance, for “Member State” or “Member States”, substitute “ F2Great Britain ”;

(b)

in section 1 (measurements), in the first paragraph, for the words from “harmonised” to “Union”, substitute “ designated standards ”;

(c)

in section 2 (product compliance verification by market surveillance authorities)—

(i)

for the first paragraph, substitute—

“When verifying the compliance of a product model with the requirements laid down in this Regulation, for the requirements referred to in this Annex the authorities of F3Great Britain must apply the following procedure—”;

(ii)

in subparagraph (2)(a)—

(aa)

for “point 2 of Annex IV to Directive 2009/125/EC (declared values)”, substitute “ paragraph 1(2) of Part 1 of Schedule 1A to the Ecodesign for Energy-Related Products Regulations 2010 ”; and

(bb)

for “paragraph (g) thereof”, substitute “ paragraph 1(2)(b)(vii) of Part 1 of Schedule 1A to those Regulations ”;

(iii)

omit subparagraph (7); and

(iv)

in the third paragraph, for “7” substitute “ 6 ”.

(8)

In Annex 4 (indicative benchmarks), for “purpose of Part 3, point 2 of Annex I to Directive 2009/125/EC” substitute “ purposes of this Regulation ”.

Annotations

Textual amendments

F1: Words in Regulations substituted (31.12.2020 immediately before IP completion day) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020 (S.I. 2020/1528), regs. 1(2), 4
F2: Words in Sch. 2 para. 17(7)(a) substituted (31.12.2020 immediately before IP completion day) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020 (S.I. 2020/1528), regs. 1(2), 6(1)(2)(b)(xvi)
F3: Words in Sch. 2 para. 17(7)(c)(i) substituted (31.12.2020 immediately before IP completion day) by The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020 (S.I. 2020/1528), regs. 1(2), 6(3)(4)(b)(xvi)

Commencement

I1: Sch. 2 para. 17 in force at 31.12.2020 on IP completion day (in accordance with 2020 c. 1, Sch. 5 para. 1(1)), see reg. 1(3)