OpenLegislation

Division 3.9.1.1 General

Original text. Later amendments are not shown.

The manufacturer shall conduct batch testing on finished containers that are representative of normal production. The finished containers to be tested shall be randomly selected from each batch. A batch shall not exceed 200 finished containers plus those finished containers to be used in destructive tests, or one shift of successive production, whichever is greater.

The frequency of batch testing can be reduced as follows:

  1. (a)

    If on 10 sequential batches of containers, none of the vessels leak or rupture within 1,5 times the required number of cycles, then the pressure cycle testing may be reduced to once per 5 batches. If any tested vessel fails to meet the requirement of 1,5 times the number of pressure cycles, then batch testing shall be required for the next five batches to re-establish the reduced frequency of testing.

  2. (b)

    If on 10 sequential batches of containers, none of the vessels leak or rupture within 2 times the required number of cycles, then the pressure cycle testing may be reduced to once per 10 batches. If any tested vessel fails to meet the requirement of 2 times the number of pressure cycles, then batch testing shall be required for the next ten batches to re-establish the reduced frequency of testing.

  3. (c)

    If more than 3 months elapse since the last batch pressure cycle test, then a vessel from the next batch of production shall be pressure tested to maintain the reduced frequency.

The following batch tests are required:

  1. (a)

    One finished container shall be subjected to the ambient temperature pressure cycle test at the frequency given in section 3.9.1.2.;

  2. (b)

    One finished container, liner or heat-treated test sample that is representative of finished containers or liners, shall be subjected to the other tests specified in Table IV.3.9.;

  3. (c)

    One finished container shall be subjected to the burst test. If a finished container passes the ambient temperature pressure cycle test the same container may be subjected to the burst test;

  4. (d)

    If an exterior environmental protective coating is used, e.g. organic coating/paint, one finished container or test sample that is representative of the batch shall be subjected to the coating batch test.

If more containers than required are subjected to the tests, all results shall be documented.

All containers represented by a batch test that fail to meet the specified requirements shall follow the procedures specified in section 3.9.2.

Table IV.3.9.

Batch tests

Explanatory notes:
  1. (a)

    For steel containers or liners refer to section 10.2. of ISO 9809-1 or section 10.2. of ISO 9809-2 as appropriate;

  2. (b)

    For stainless steel containers or liners refer to section 7.1.2.1. of EN 1964-3;

  3. (c)

    For welded stainless steel liners refer to section 8.4. of EN 13322-2;

  4. (d)

    For aluminium alloy containers or liners refer to section 10.2. of ISO 7866;

  5. (e)

    For welded aluminium alloy liners refer to sections 7.2.3. and 7.2.4. of EN 12862;

  6. (f)

    For non-metallic liners refer to section 4.1.1.;

  1. (a)

    For steel containers or liners refer to section 10.4. of ISO 9809-1 or section 10.4. of ISO 9809-2 as appropriate;

  2. (b)

    For stainless steel containers or liners refer to section 7.1.2.4. of EN 1964-3;

  3. (c)

    For welded stainless steel liners refer to section 8.6. of EN 13322-2;

  1. (a)

    For welded stainless steel liners refer to section 8.5. of EN 13322-2;

  2. (b)

    For welded aluminium alloy liners refer to sections 7.2.5., 7.2.6. and 7.2.7. of EN 12862;

For welded stainless steel liners refer to section 8.7. of EN 13322-2.

Test on liner material.

The following test sequence shall be used for container type 4: boss torque test (section 4.2.13.), followed by an ambient temperature pressure cycling test (section 4.2.2.), followed by a leak test (section 4.2.11.).

A leak test shall be carried out on all welded metal liners.

Test and referenceApplicable to container typeSpecified design valueTest value
1234
f1Tensile testf2
f3Charpy impact test
f4Bend test
f5Macroscopic examination
4.1.2.Softening temperature test
4.1.6.Coating batch test
4.2.1.Burst test
4.2.2.Ambient temperature pressure cycle testf6
4.2.11.Leak testf7
4.2.13.Boss torque test

Annotations

Footnotes

f1
  1. (a)

    For steel containers or liners refer to section 10.2. of ISO 9809-1 or section 10.2. of ISO 9809-2 as appropriate;

  2. (b)

    For stainless steel containers or liners refer to section 7.1.2.1. of EN 1964-3;

  3. (c)

    For welded stainless steel liners refer to section 8.4. of EN 13322-2;

  4. (d)

    For aluminium alloy containers or liners refer to section 10.2. of ISO 7866;

  5. (e)

    For welded aluminium alloy liners refer to sections 7.2.3. and 7.2.4. of EN 12862;

  6. (f)

    For non-metallic liners refer to section 4.1.1.;

f2

Test on liner material.

f3
  1. (a)

    For steel containers or liners refer to section 10.4. of ISO 9809-1 or section 10.4. of ISO 9809-2 as appropriate;

  2. (b)

    For stainless steel containers or liners refer to section 7.1.2.4. of EN 1964-3;

  3. (c)

    For welded stainless steel liners refer to section 8.6. of EN 13322-2;

f4
  1. (a)

    For welded stainless steel liners refer to section 8.5. of EN 13322-2;

  2. (b)

    For welded aluminium alloy liners refer to sections 7.2.5., 7.2.6. and 7.2.7. of EN 12862;

f5

For welded stainless steel liners refer to section 8.7. of EN 13322-2.

f6

The following test sequence shall be used for container type 4: boss torque test (section 4.2.13.), followed by an ambient temperature pressure cycling test (section 4.2.2.), followed by a leak test (section 4.2.11.).

f7

A leak test shall be carried out on all welded metal liners.