OpenLegislation

Division 3.10.1.1

United Kingdom

Original text. Later amendments are not shown.

The air drag pre-processing tool accepts datasets as recorded during the constant speed test in case the following validity criteria are met:

  1. i..

    the average vehicle speed is inside the criteria as defined in 3.5.2

  2. ii..

    the ambient temperature is inside the range as described in 3.2.2. This criterion is checked by the air drag pre-processing tool based on the ambient temperature measured on the vehicle.

  3. iii..

    the proving ground temperature is in the range as described in 3.2.3

  4. iv..

    valid average wind speed conditions according to point 3.2.5 item i

  5. v..

    valid gust wind speed conditions according to point 3.2.5 item ii

  6. vi..

    valid average yaw angle conditions according to point 3.2.5 item iii

  7. vii..

    stability criteria for vehicle speed met:

    • Low speed test:

      v lms,avrg − 0,5 km ∕ h ≤ v lm,avrg ≤ v lms,avrg + 0,5 km ∕ h

      where:

      vlms,avrg
    • average of vehicle speed per measurement section [km/h]

    • vlm,avrg
    • central moving average of vehicle speed with Xms seconds time base [km/h]

    • Xms
    • time needed to drive 25 m distance at actual vehicle speed [s]

    • High speed test:

      v hms,avrg − 0,3 km ∕ h ≤ v hm,avrg ≤ v hms,avrg + 0,3 km ∕ h

      where:

      vhms,avrg
    • average of vehicle speed per measurement section [km/h]

    • vhm,avrg
    • 1 s central moving average of vehicle speed [km/h]

  8. viii..

    stability criteria for vehicle torque met:

    • Low speed test:

      T lms,avrg − T grd × 0,7 ≤ T lm,avrg − T grd ≤ T lms,avrg − T grd × 1,3 T grd = F grd,avrg × r dyn,avrg

      where:

      Tlms,avrg
    • average of Tsum per measurement section

    • Tgrd
    • average torque from gradient force

    • Fgrd,avrg
    • average gradient force over measurement section

    • rdyn,avrg
    • average effective rolling radius over measurement section (formula see item ix.) [m]

    • Tsum
    • TL+TR ; sum of corrected torque values left and right wheel [Nm]

    • Tlm,avrg
    • central moving average of Tsum with Xms seconds time base

    • Xms
    • time needed to drive 25 m distance at actual vehicle speed [s]

    • High speed test

      T hms,avrg − T grd × 0,8 ≤ T hm,avrg − T grd ≤ T hms,avrg − T grd × 1,2

      where:

      Thms,avrg
    • average of Tsum per measurement section [Nm]

    • Tgrd
    • average torque from gradient force (see Low speed test) [Nm]

    • Tsum
    • TL+TR ; sum of corrected torque values left and right wheel [Nm]

    • Thm,avrg
    • 1 s central moving average of Tsum [Nm]

  9. ix..

    valid heading of the vehicle passing a measurement section (< 10° deviation from target heading applicable for low speed test, high speed test and misalignment test)

  10. x..

    driven distance inside measurement section calculated from the calibrated vehicle speed does not differ from target distance by more than 3 meters (applicable for low speed test and high speed test)

  11. xi..

    F1plausibility check for engine speed or cardan speed whichever is applicable passed:

    Engine speed check for high speed test:

    30 × i gear × i axle × v hms,avrg − 0,3 3,6 r dyn,ref,HS × π × 1 − 0,02 ≤ n eng, 1 s ≤ 30 × i gear × i axle × v hms,avrg + 0,3 3,6 r dyn,ref,HS × π × 1 + 0,02

    r dyn,avrg = 30 × i gear × i axle × v hms,avrg 3,6 n eng,avrg × π

    r dyn,ref,HS = 1 n ∑ j = 1 n r dyn,avrg,j

    where:

    i gear
  12. transmission ratio of the gear selected in high speed test [-]

  13. i axle
  14. axle transmission ratio [-]

  15. v hms,avrg
  16. average vehicle speed (high speed measurement section) [km/h]

  17. n eng,1s
  18. 1 s central moving average of engine speed (high speed measurement section) [rpm]

  19. n eng,avrg
  20. average engine speed (high speed measurement section) [rpm]

  21. r dyn,avrg
  22. average effective rolling radius for a single high speed measurement section [m]

  23. r dyn,ref,HS
  24. reference effective rolling radius calculated from all valid high speed measurement sections (number = n) [m]

  25. Engine speed check for low speed test:

    30 × i gear × i axle × v lms,avrg − 0,5 3,6 r dyn,ref,LS 1 ∕ LS 2 × π × 1 − 0,02 ≤ n eng,float ≤ 30 × i gear × i axle × v lms,avrg + 0,5 3,6 r dyn,ref,LS 1 ∕ LS 2 × π × 1 + 0,02

    r dyn,avrg = 30 × i gear × i axle × v lms,avrg 3,6 n eng,avrg × π

    r dyn,ref,LS 1 ∕ LS 2 = 1 n ∑ j = 1 n r dyn,avrg,j

    where:

    i gear
  26. transmission ratio of the gear selected in low speed test [-]

  27. i axle
  28. axle transmission ratio [-]

  29. v lms,avrg
  30. average vehicle speed (low speed measurement section) [km/h]

  31. n eng,float
  32. central moving average of engine speed with X ms seconds time base (low speed measurement section) [rpm]

  33. n eng,avrg
  34. average engine speed (low speed measurement section) [rpm]

  35. X ms
  36. time needed to drive 25 metre distance at low speed [s]

  37. r dyn,avrg
  38. average effective rolling radius for a single low speed measurement section [m]

  39. r dyn,ref,LS1/LS2
  40. reference effective rolling radius calculated from all valid measurement sections for low speed test 1 or low speed test 2 (number = n) [m]

  41. The plausibility check for cardan speed is performed in an analogue way with n eng,1s replaced by n card,1s (1 s central moving average of cardan speed in the high speed measurement section) and n eng,float replaced by n card,float (moving average of cardan speed with X ms seconds time base in the low speed measurement section) and i gear set to a value of 1.

  • xii..

    the particular part of the measurement data was not marked as ‘invalid’ in the air drag pre-processing tool input file.

  • Annotations

    Textual amendments

    F1

    Substituted by Commission Regulation (EU) 2019/318 of 19 February 2019 amending Regulation (EU) 2017/2400 and Directive 2007/46/EC of the European Parliament and of the Council as regards the determination of the CO2 emissions and fuel consumption of heavy-duty vehicles (Text with EEA relevance).