OpenLegislation

Division BAT 15 In order to reduce VOC emissions in waste gases and increase resource efficiency, BAT is to use one or a combination of the techniques given below.

United Kingdom

Original text. Later amendments are not shown.

TechniqueDescriptionApplicability
I. Capture and recovery of solvents in off-gases
(a)CondensationA technique for removing organic compounds by reducing the temperature below their dew points so that the vapours liquefy. Depending on the operating temperature range required, different refrigerants are used, e.g. cooling water, chilled water (temperature typically around 5 °C), ammonia or propane.Applicability may be restricted where the energy demand for recovery is excessive due to the low VOC content.
(b)Adsorption using activated carbon or zeolitesVOCs are adsorbed on the surface of activated carbon, zeolites or carbon fibre paper. Adsorbate is subsequently desorbed, e.g. with steam (often on site), for reuse or disposal and the adsorbent is reused. For continuous operation, typically more than two adsorbers are operated in parallel, one of them in desorption mode. Adsorption is also commonly applied as a concentration step to increase the subsequent oxidation efficiency.Applicability may be restricted where the energy demand for recovery is excessive due to the low VOC content.
(c)Absorption using a suitable liquid

Use of a suitable liquid to remove pollutants from the off-gas by absorption, in particular soluble compounds and solids (dust). Solvent recovery is possible, for example, using distillation or thermal desorption.

(For dust removal, see BAT 18.)

Generally applicable.
II. Thermal treatment of solvents in off-gases with energy recovery
(d)Sending off-gases to a combustion plantPart or all of the off-gases are sent as combustion air and supplementary fuel to a combustion plant (including CHP (combined heat and power) plants) used for steam and/or electricity production.Not applicable for off-gases containing substances referred to in IED Article 59(5). Applicability may be restricted due to safety considerations.
(e)Recuperative thermal oxidationThermal oxidation using the heat of the waste gases, e.g. to preheat the incoming off-gases.Generally applicable.
(f)Regenerative thermal oxidation with multiple beds or with a valveless rotating air distributorAn oxidiser with multiple beds (three or five) filled with ceramic packing. The beds are heat exchangers, alternately heated by flue-waste gases from oxidation, then the flow is reversed to heat the inlet air to the oxidiser. The flow is reversed on a regular basis. In the valveless rotating air distributor, the ceramic medium is held in a single rotating vessel divided into multiple wedges.Generally applicable.
(g)Catalytic oxidationOxidation of VOCs assisted by a catalyst to reduce the oxidation temperature and reduce the fuel consumption. Exhaust heat can be recovered with recuperative or regenerative types of heat exchangers. Higher oxidation temperatures (500–750 °C) are used for the treatment of off-gas from the manufacturing of winding wire.Applicability may be restricted by the presence of catalyst poisons.
III. Treatment of solvents in off-gases without solvent or energy recovery
(h)Biological off-gas treatmentOff-gas is dedusted and sent to a reactor with biofilter substrate. The biofilter consists of a bed of organic material (such as peat, heather, compost, root, tree bark, softwood and different combinations) or some inert material (such as clay, activated carbon, and polyurethane), where the off-gas stream is biologically oxidised by naturally occurring microorganisms into carbon dioxide, water, inorganic salts and biomass. The biofilter is sensitive to dust, high temperatures or high variations in the off-gas, e.g. of the inlet temperature or the VOC concentration. Supplementary nutrient feeding may be needed.Only applicable to the treatment of biodegradable solvents.
(i)Thermal oxidationOxidation of VOCs by heating off-gases with air or oxygen to above their auto-ignition point in a combustion chamber and maintaining a high temperature long enough to complete the combustion of VOCs to carbon dioxide and water.Generally applicable.

BAT-associated emission levels (BAT-AELs) are given in Tables 11, 15, 17, 19, 21, 24, 27, 30, 32 and 35 of these BAT conclusions.