Appendix 3 MODEL
United Kingdom
relating to EC type-approval of a vehicle with regard to emissions and access to vehicle repair and maintenance information
The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, must show sufficient detail.
If the systems, components or separate technical units have electronic controls, information concerning their performance must be supplied.
0.
GENERAL
0.1.
Make (trade name of manufacturer):
0.2.
Type:
0.2.1.
Commercial name(s), if available
0.3.
0.3.1.
Location of that marking:
0.4.
Category of vehiclef3:
0.5.
Name and address of manufacturer:
0.8.
Name(s) and address(es) of assembly plant(s):
0.9.
Name and address of the manufacturer’s representative (if any)
1.
GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
1.1.
Photographs and/or drawings of a representative vehicle:
1.3.3.
Powered axles (number, position, interconnection):
2.
MASSES AND DIMENSIONSf4 (in kg and mm)
(Refer to drawing where applicable)
2.6.
Mass of the vehicle with bodywork and, in the case of the towing vehicle of a category other than M1, with coupling device, if fitted by the manufacturer, in running order, or mass of the chassis or chassis with cab, without bodywork and/or coupling device if the manufacturer does not fit the bodywork and/or coupling device (including liquids, tools, spare wheel, if fitted, and driver and, for buses and coaches, a crew member if there is a crew seat in the vehicle)f5 (maximum and minimum for each variant):
2.8.
F12.17.
Vehicle submitted to multi-stage type-approval (only in the case of incomplete or completed vehicles of category N 1 within the scope of Regulation (EC) No 715/2007): yes/no
2.17.1.
Mass of the base vehicle in running order: kg
2.17.2.
Default added mass, calculated in accordance with Section 5 of Annex XII to Regulation (EC) No 692/2008: … kg
F23.
PROPULSION ENERGY CONVERTER (k)
3.1.
Manufacturer of the propulsion energy converter(s):
3.1.1.
Manufacturer's code (as marked on the propulsion energy converter or other means of identification):
3.2.
Internal combustion engine
3.2.1.1.
Working principle: positive ignition/compression ignition …
four stroke/two stroke/rotary cycle …
3.2.1.2.
Number and arrangement of cylinders:
3.2.1.2.1.
Boref8: mm
3.2.1.2.2.
Stroke: mm
3.2.1.2.3.
Firing order:
3.2.1.3.
Engine capacity (s): … cm3
3.2.1.4.
Volumetric compression ratiof9
3.2.1.5.
Drawings of combustion chamber, piston crown and, in the case of positive ignition engine, piston rings:
3.2.1.6.
Normal engine idling speed … min-1
3.2.1.6.1.
High engine idling speed … min-1
3.2.1.7.
Carbon monoxide content by volume in the exhaust gas with the engine idling … as stated by the manufacturer (positive ignition engines only)
3.2.1.8.
Rated engine power (n): … kW at … min –1 (manufacturer's declared value)
3.2.1.9.
Maximum permitted engine speed as prescribed by the manufacturer: … min-1
3.2.1.10.
Maximum net torquef10: Nm at … min-1 (manufacturer’s declared value)
F33.2.2.
Fuel
F43.2.2.1.
Light-duty vehicles: Diesel/Petrol/LPG/NG or Biomethane/Ethanol (E85) /Biodiesel /Hydrogen/H2NG f11
3.2.2.1.1.
RON, unleaded:
3.2.2.3.
Fuel tank inlet: restricted orifice/label
3.2.2.4.
Vehicle fuel type: Mono fuel, Bi fuel, Flex fuel
3.2.2.5.
Maximum amount of biofuel acceptable in fuel (manufacturer’s declared value): … % by volume
3.2.4.
Fuel feed
3.2.4.2.
By fuel injection (compression ignition only): yes/no
3.2.4.2.1.
System description (common rail/unit injectors/distribution pump etc.):
3.2.4.2.2.
Working principle: direct injection/pre-chamber/swirl chamber
3.2.4.2.3.
Injection/Delivery pump
3.2.4.2.3.1.
Make(s):
3.2.4.2.3.2.
Type(s):
3.2.4.2.3.3.
Maximum fuel delivery mm3/stroke or cycle at an engine speed of: … min-1 or, alternatively, a characteristic diagram:
3.2.4.2.3.5.
Injection advance curve:
3.2.4.2.4.
Engine speed limitation control
3.2.4.2.4.2.
Cut-off point
3.2.4.2.4.2.1.
Cut-off point under load … min-1
3.2.4.2.4.2.2.
Cut-off point without load … min-1
3.2.4.2.6.
Injector(s)
3.2.4.2.6.1.
Make(s):
3.2.4.2.6.2.
Type(s):
3.2.4.2.7.
Cold start system
3.2.4.2.7.1.
Make(s):
3.2.4.2.7.2.
Type(s):
3.2.4.2.7.3.
Description:
3.2.4.2.8.
Auxiliary starting aid
3.2.4.2.8.1.
Make(s):
3.2.4.2.8.2.
Type(s):
3.2.4.2.8.3.
System description:
3.2.4.2.9.
Electronic controlled injection: yes/no
3.2.4.2.9.1.
Make(s):
3.2.4.2.9.2.
Type(s):
3.2.4.2.9.3.
Description of the system
3.2.4.2.9.3.1.
Make and type of the control unit:
3.2.4.2.9.3.2.
Make and type of the fuel regulator:
3.2.4.2.9.3.3.
Make and type of air-flow sensor:
3.2.4.2.9.3.4.
Make and type of fuel distributor:
3.2.4.2.9.3.5.
Make and type of throttle housing:
3.2.4.2.9.3.6.
Make and type or working principle of water temperature sensor:
3.2.4.2.9.3.7.
Make and type or working principle of air temperature sensor:
3.2.4.2.9.3.8.
Make and type or working principle of air pressure sensor:
3.2.4.3.
By fuel injection (positive ignition only): yes/no
3.2.4.3.1.
Working principle: intake manifold (single-/multi-point)/direct injection/other (specify)
3.2.4.3.2.
Make(s):
3.2.4.3.3.
Type(s):
3.2.4.3.4.
System description, in the case of systems other than continuous injection give equivalent details:
3.2.4.3.4.1.
Make and type of the control unit:
3.2.4.3.4.3.
Make and type or working principle of air-flow sensor:
3.2.4.3.4.6.
Make and type of micro switch:
3.2.4.3.4.8.
Make and type of throttle housing:
3.2.4.3.4.9.
Make and type or working principle of water temperature sensor:
3.2.4.3.4.10.
Make and type or working principle of air temperature sensor:
3.2.4.3.4.11.
Make and type or working principle of air pressure sensor:
3.2.4.3.5.
Injectors
3.2.4.3.5.1.
Make(s):
3.2.4.3.5.2.
Type(s):
3.2.4.3.6.
Injection timing:
3.2.4.3.7.
Cold start system
3.2.4.3.7.1.
Operating principle(s):
3.2.4.3.7.2.
Operating limits/settings :
3.2.4.4.
Feed pump
3.2.4.4.1.
Pressure: … kPa or characteristic diagram:
3.2.5.
Electrical system
3.2.5.1.
Rated voltage: V, positive/negative ground
3.2.5.2.
Generator
3.2.5.2.1.
Type:
3.2.5.2.2.
Nominal output: … VA
3.2.6.
Ignition
3.2.6.1.
Make(s):
3.2.6.2.
Type(s):
3.2.6.3.
Working principle:
3.2.6.4.
Ignition advance curve:
3.2.6.5.
Static ignition timing: … degrees before TDC
3.2.7.
Cooling system: liquid/air
3.2.7.1.
Nominal setting of the engine temperature control mechanism:
3.2.7.2.
Liquid
3.2.7.2.1.
Nature of liquid:
3.2.7.2.2.
Circulating pump(s):yes/no
3.2.7.2.3.
Characteristics, or
3.2.7.2.3.1.
Make(s):
3.2.7.2.3.2.
Type(s):
3.2.7.2.4.
Drive ratio(s):
3.2.7.2.5.
Description of the fan and its drive mechanism:
3.2.7.3.
Air
3.2.7.3.1.
Blower: yes/no
3.2.7.3.2.
Characteristics:, or
3.2.7.3.2.1.
Make(s):
3.2.7.3.2.2.
Type(s):
3.2.7.3.3.
Drive ratio(s):
3.2.8.
Intake system
3.2.8.1.
Pressure charger: yes/no
3.2.8.1.1.
Make(s):
3.2.8.1.2.
Type(s):
3.2.8.1.3.
Description of the system (e.g. maximum charge pressure: … kPa, wastegate if applicable):
3.2.8.2.
Intercooler: yes/no
3.2.8.2.1.
Type: air-air/air-water
3.2.8.3.
Intake depression at rated engine speed and at 100 % load (compression ignition engines only)
Minimum allowable: kPa
Maximum allowable: kPa
3.2.8.4.
Description and drawings of the inlet pipes and their accessories (plenum chamber, heating device, additional air intakes, etc.):
3.2.8.4.1.
Intake manifold description (include drawings and/or photos):
3.2.8.4.2.
Air filter, drawings: … or
3.2.8.4.2.1.
Make(s):
3.2.8.4.2.2.
Type(s):
3.2.8.4.3.
Intake silencer, drawings: … or
3.2.8.4.3.1.
Make(s):
3.2.8.4.3.2.
Type(s):
3.2.9.
Exhaust system
3.2.9.1.
Description and/or drawing of the exhaust manifold:
3.2.9.2.
Description and/or drawing of the exhaust system:
3.2.9.3.
Maximum allowable exhaust back pressure at rated engine speed and at 100 % load (compression ignition engines only): kPa
3.2.10.
Minimum cross-sectional areas of inlet and outlet ports:
3.2.11.
Valve timing or equivalent data
3.2.11.1.
Maximum lift of valves, angles of opening and closing, or timing details of alternative distribution systems, in relation to dead centres. For variable timing system, minimum and maximum timing:
3.2.11.2.
Reference and/or setting ranges:
3.2.12.
Measures taken against air pollution
3.2.12.1.
Device for recycling crankcase gases (description and drawings):
3.2.12.2.
Pollution control devices (if not covered by another heading)
3.2.12.2.1.
Catalytic converter
3.2.12.2.1.1.
Number of catalytic converters and elements (provide the information below for each separate unit):
3.2.12.2.1.2.
Dimensions, shape and volume of the catalytic converter:
3.2.12.2.1.3.
Type of catalytic action:
3.2.12.2.1.4.
Total charge of precious metals:
3.2.12.2.1.5.
Relative concentration:
3.2.12.2.1.6.
Substrate (structure and material):
3.2.12.2.1.7.
Cell density:
3.2.12.2.1.8.
Type of casing for the catalytic converter(s):
3.2.12.2.1.9.
Location of the catalytic converter(s) (place and reference distance in the exhaust line):
3.2.12.2.1.10.
Heat shield: yes/no
F53.2.12.2.1.11.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.5.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.6.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.7.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.8.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.9.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.11.10.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.12.
Make of catalytic converter:
3.2.12.2.1.13.
Identifying part number:
3.2.12.2.2.
Sensors
3.2.12.2.2.1.
Oxygen sensor: yes/no
3.2.12.2.2.1.1.
Make:
3.2.12.2.2.1.2.
Location:
3.2.12.2.2.1.3.
Control range:
3.2.12.2.2.1.4.
Type or working principle: …
3.2.12.2.2.1.5.
Identifying part number: …
3.2.12.2.3.
Air injection: yes/no
3.2.12.2.3.1.
Type (pulse air, air pump etc.):
3.2.12.2.4.
Exhaust gas recirculation: yes/no
3.2.12.2.4.1.
Characteristics (make, type, flow, high pressure / low pressure / combined pressure, etc.):
3.2.12.2.4.2.
Water-cooled system (to be specified for each EGR system e.g. low pressure / high pressure / combined pressure: yes/no
3.2.12.2.5.
Evaporative emissions control system (petrol and ethanol engines only): yes/no
3.2.12.2.5.1.
Detailed description of the devices:
3.2.12.2.5.2.
Drawing of the evaporative emissions control system:
3.2.12.2.5.3.
Drawing of the carbon canister:
3.2.12.2.5.4.
Mass of dry charcoal: … g
3.2.12.2.5.5.
Schematic drawing of the fuel tank with indication of capacity and material (petrol and ethanol engines only): …
3.2.12.2.5.6.
Description and schematic of the heat shield between tank and exhaust system: …
F63.2.12.2.5.7.
Permeability factor : …
3.2.12.2.6.
Particulate trap: yes/no
3.2.12.2.6.1.
Dimensions, shape and capacity of the particulate trap:
3.2.12.2.6.2.
Type and design of the particulate trap:
3.2.12.2.6.3.
Location (reference distance in the exhaust line):
3.2.12.2.6.4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.4.1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.4.2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.4.3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.4.4.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.4.
Make of particulate trap: …
3.2.12.2.6.5.
Identifying part number: …
3.2.12.2.7.
On-board-diagnostic (OBD) system: (yes/no)
3.2.12.2.7.1.
Written description and/or drawing of the MI:
3.2.12.2.7.2.
List and purpose of all components monitored by the OBD system:
3.2.12.2.7.3.
Written description (general working principles) for:
3.2.12.2.7.3.1.
Positive-ignition engines
3.2.12.2.7.3.1.1.
Catalyst monitoring:
3.2.12.2.7.3.1.2.
Misfire detection:
3.2.12.2.7.3.1.3.
Oxygen sensor monitoring:
3.2.12.2.7.3.1.4.
Other components monitored by the OBD system:
3.2.12.2.7.3.2.
Compression-ignition engines
3.2.12.2.7.3.2.1.
Catalyst monitoring:
3.2.12.2.7.3.2.2.
Particulate trap monitoring:
3.2.12.2.7.3.2.3.
Electronic fuelling system monitoring:
3.2.12.2.7.3.2.4.
Other components monitored by the OBD system:
3.2.12.2.7.4.
Criteria for MI activation (fixed number of driving cycles or statistical method):
3.2.12.2.7.5.
List of all OBD output codes and formats used (with explanation of each):
3.2.12.2.7.6.
The following additional information shall be provided by the vehicle manufacturer for the purposes of enabling the manufacture of OBD-compatible replacement or service parts and diagnostic tools and test equipment.
The information given in this section shall be repeated in Appendix 5 to this Annex (vehicle OBD information appendix to the EC type-approval certificate):
3.2.12.2.7.6.1.
A description of the type and number of the pre-conditioning cycles used for the original type-approval of the vehicle.
3.2.12.2.7.6.2.
A description of the type of the OBD demonstration cycle used for the original type-approval of the vehicle for the component monitored by the OBD system.
3.2.12.2.7.6.3.
A comprehensive document describing all sensed components with the strategy for fault detection and MI activation (fixed number of driving cycles or statistical method), including a list of relevant secondary sensed parameters for each component monitored by the OBD system. A list of all OBD output codes and format used (with an explanation of each) associated with individual emission related power-train components and individual non-emission related components, where monitoring of the component is used to determine MI activation. In particular, a comprehensive explanation for the data given in service $05 Test ID $21 to FF and the data given in service $06 shall be provided. In the case of vehicle types that use a communication link in accordance with ISO 15765-4 ‘Road vehicles diagnostics on controller area network (CAN) — part 4: requirements for emissions-related systems’, a comprehensive explanation for the data given in service $06 Test ID $00 to FF, for each OBD monitor ID supported, shall be provided.
3.2.12.2.7.6.4.
The information required by this section may, for example, be defined by completing a table as follows, which shall be attached to this Annex.
| Component | Fault code | Monitoring strategy | Fault detection criteria | MI activation criteria | Secondary parameters | Preconditioning | Demonstration test |
|---|---|---|---|---|---|---|---|
| Catalyst | PO420 | Oxygen sensor 1 and 2 signals | Difference between sensor 1 and sensor 2 signals | 3rd cycle | Engine speed, engine load, A/F mode, catalyst temperature | Two Type 1 cycles | Type 1 |
3.2.12.2.8.
Other system:
F73.2.12.2.10.
Periodically regenerating system: (provide the information below for each separate unit)
3.2.12.2.10.1.
Method or system of regeneration, description and/or drawing: …
3.2.12.2.10.2.
The number of Type 1 operating cycles, or equivalent engine test bench cycles, between two cycles where regenerative phases occur under the conditions equivalent to Type 1 test (Distance ‘ D ’ in Figure A6.App1/1 in Appendix 1 to Sub-Annex 6 of Annex XXI to Regulation (EU) 2017/1151 or figure A13/1 in Annex 13 to UN/ECE Regulation 83 (as applicable)): …
3.2.12.2.10.2.1.
Applicable Type 1 cycle: (indicate the applicable procedure: Annex XXI, Sub-Annex 4 or UN/ECE Regulation 83): …
3.2.12.2.10.3.
Description of method employed to determine the number of cycles between two cycles where regenerative phases occur: …
3.2.12.2.10.4.
Parameters to determine the level of loading required before regeneration occurs (i.e. temperature, pressure etc.): …
3.2.12.2.10.5.
Description of method used to load system in the test procedure described in paragraph 3.1., Annex 13 to UN/ECE Regulation 83: …
3.2.12.2.11.
Catalytic converter systems using consumable reagents (provide the information below for each separate unit) yes/no
3.2.12.2.11.1.
Type and concentration of reagent needed: …
3.2.12.2.11.2.
Normal operational temperature range of reagent: …
3.2.12.2.11.3.
International standard: …
3.2.12.2.11.4.
Frequency of reagent refill: continuous/maintenance (where appropriate):
3.2.12.2.11.5.
Reagent indicator: (description and location)
3.2.12.2.11.6.
Reagent tank
3.2.12.2.11.6.1.
Capacity: …
3.2.12.2.11.6.2.
Heating system: yes/no
3.2.12.2.11.6.2.1.
Description or drawing
3.2.12.2.11.7.
Reagent control unit: yes/no
3.2.12.2.11.7.1.
Make: …
3.2.12.2.11.7.2.
Type: …
3.2.12.2.11.8.
Reagent injector (make, type and location): …
3.2.13.
Location of the absorption coefficient symbol (compression ignition engines only):
3.2.14.
Details of any devices designed to influence fuel economy (if not covered by other items):
3.2.15.
LPG fuelling system: yes/no
3.2.15.1.
Type-approval number according to Regulation (EC) No 661/2009 ( OJ L 200, 31.7.2009, p. 1 )
3.2.15.2.
Electronic engine management control unit for LPG fuelling
3.2.15.2.1.
Make(s):
3.2.15.2.2.
Type(s):
3.2.15.2.3.
Emission-related adjustment possibilities:
3.2.15.3.
Further documentation
3.2.15.3.1.
Description of the safeguarding of the catalyst at switch-over from petrol to LPG or back:
3.2.15.3.2.
System lay-out (electrical connections, vacuum connections compensation hoses, etc.):
3.2.15.3.3.
Drawing of the symbol:
3.2.16.
NG fuelling system: yes/no
3.2.16.1.
Type-approval number according to Regulation (EC) No 661/2009 ( OJ L 200, 31.7.2009, p. 1 )
3.2.16.2.
Electronic engine management control unit for NG fuelling
3.2.16.2.1.
Make(s):
3.2.16.2.2.
Type(s):
3.2.16.2.3.
Emission-related adjustment possibilities:
3.2.16.3.
Further documentations
3.2.16.3.1.
Description of the safeguarding of the catalyst at switch-over from petrol to NG or back:
3.2.16.3.2.
System lay-out (electrical connections, vacuum connections compensation hoses, etc.):
3.2.16.3.3.
Drawing of the symbol:
3.2.18.
Hydrogen fuelling system: yes/no
3.2.18.1.
EC type-approval number according to Regulation (EC) No 79/2009:
3.2.18.2.
Electronic engine management control unit for hydrogen fuelling
3.2.18.2.1.
Make(s):
3.2.18.2.2.
Type(s):
3.2.18.2.3.
Emission-related adjustment possibilities:
3.2.18.3.
Further documentation
3.2.18.3.1.
Description of the safeguarding of the catalyst at switch-over from petrol to hydrogen or back:
3.2.18.3.2.
System lay-out (electrical connections, vacuum connections compensation hoses, etc.):
3.2.18.3.3.
Drawing of the symbol:
3.2.19.
H2NG fuelling system: yes/no
3.2.19.1.
Percentage of hydrogen in the fuel (the maximum specified by the manufacturer):
3.2.19.2.
EC type-approval number according to UN/ECE Regulation No 110 f12
3.2.19.3.
Electronic engine management control unit for H2NG fuelling
3.2.19.3.1.
Make(s):
3.2.19.3.2.
Type(s):
3.2.19.3.3.
Emission-related adjustment possibilities:
3.2.19.4.
Further documentation
3.2.19.4.1.
Description of the safeguarding of the catalyst at switch-over from petrol to H2NG or back:
3.2.19.4.2.
System lay-out (electrical connections, vacuum connections compensation hoses, etc.):
3.2.19.4.3.
Drawing of the symbol:
3.3.
Electric machine
3.3.1.
Type (winding, excitation): …
F83.3.1.1.
Maximum hourly output:kW
(manufacturer’s declared value)
3.3.1.1.1.
Maximum net power ( a )kW
(manufacturer’s declared value)
3.3.1.1.2.
Maximum 30 minutes power (a)kW
(manufacturer’s declared value)
3.3.1.2.
Operating voltage:… V
3.3.2.
REESS
3.3.2.1.
Number of cells:
3.3.2.2.
Mass:kg
3.3.2.3.
Capacity: … Ah (Amp-hours)
3.3.2.4.
Position:
3.4.
Combinations of propulsion energy converters
3.4.1.
Hybrid Electric Vehicle: yes/no
3.4.2.
Category of Hybrid Electric vehicle
Off Vehicle Charging/Not Off Vehicle Charging
3.4.3.
Operating mode switch: with/without
3.4.3.1.
Selectable modes
3.4.3.1.1.
Pure electric: yes/no
3.4.3.1.2.
Pure fuel consuming: yes/no
3.4.3.1.3.
Hybrid modes: yes/no
(if yes, short description)
3.4.4.
Description of the energy storage device: (REESS, capacitor, flywheel/generator)
3.4.4.1.
Make(s):
3.4.4.2.
Type(s):
3.4.4.3.
Identification number:
3.4.4.4.
Kind of electrochemical couple: ….
3.4.4.5.
Energy: … (for REESS: voltage and capacity Ah in 2 h, for capacitor: J, …)
3.4.4.6.
Charger: on board/external/without
3.4.5.
Electric machine (describe each type of electric machine separately)
3.4.5.1.
Make:
3.4.5.2.
Type: ….
3.4.5.3.
Primary use: traction motor/generator
3.4.5.3.1.
When used as traction motor: monomotor/multimotors (number):
3.4.5.4.
Maximum power: kW
3.4.5.5.
Working principle:
3.4.5.5.1.
direct current/alternating current/number of phases:
3.4.5.5.2.
separate excitation/series/compound
3.4.5.5.3.
synchronous/asynchronous
3.4.6.
Control unit
3.4.6.1.
Make(s):
3.4.6.2.
Type(s):
3.4.6.3.
Identification number:
3.4.7.
Power controller
3.4.7.1.
Make:
3.4.7.2.
Type:
3.4.7.3.
Identification number:
3.4.8.
Vehicle electric range … … km (in accordance to Annex 9 to UN/ECE Regulation No 101 f13
3.4.9.
Manufacturer’s recommendation for preconditioning:
3.5.
Manufacturer’s declared values for determination of CO 2 emissions/fuel consumption/electric consumption/electric range and details of eco-innovations (where applicable) f14
3.5.1.
CO2 mass emissions (provide for each reference fuel tested)
3.5.1.1.
CO2 mass emissions (urban conditions): … g/km
3.5.1.2.
CO2 mass emissions (extra-urban conditions): … g/km
3.5.1.3.
CO2 mass emissions (combined): … g/km
3.5.2.
Fuel consumption (provide for each reference fuel tested)
3.5.2.1.
Fuel consumption (urban conditions) … l/100 km or m 3 /100 km or kg/100 km
3.5.2.2.
Fuel consumption (extra-urban conditions) … l/100 km or m 3 /100 km or kg/100 km
3.5.2.3.
Fuel consumption (combined) … l/100 km or m 3 /100 km or kg/100 km
F9 3.5.3.
Electric energy consumption for electric vehicles
3.5.3.1.
Type/Variant/Version of the baseline vehicle as defined in Article 5 of Implementing Regulation (EU) No 725/2011 f15
F103.5.3.1.
Electric energy consumption for pure electric vehicles … Wh/km
3.5.3.2.
Interactions existing between different eco-innovations: yes/no f16
3.5.3.2.
Electric energy consumption for externally chargeable hybrid electric vehicles
3.5.3.2.1.
Electric energy consumption (Condition A, combined) Wh/km
3.5.3.2.2.
Electric energy consumption (Condition B, combined) Wh/km
3.5.3.2.3.
Electric energy consumption (weighted combined) Wh/km
3.5.3.3.
| Number of the Commission Decision approving the eco-innovation. | |||||||
| Assigned in the Commission Decision approving the eco-innovation. | |||||||
| Under agreement of the type-approval authority, if modelling is applied instead of the type 1 test-cycle, this value shall be the one provided by the modelling methodology. | |||||||
| Sum of the emission s saving of each individual eco-innovation. | |||||||
| Decision approving the eco-innovation f19 | Code of the eco-innovation f20 | 1. CO 2 emissions of the baseline vehicle (g/km) | 2. CO 2 emissions of the eco-innovation vehicle (g/km) | 3. CO 2 emissions of the baseline vehicle under type 1 test-cycle f21 | 4. CO 2 emissions of the eco-innovation vehicle under type 1 test-cycle (= 3.5.1.3) | 5. Usage factor (UF)i.e. temporal share of technology usage in normal operation conditions | CO 2 emissions savings |
|---|---|---|---|---|---|---|---|
| xxxx/201x | |||||||
| Total CO 2 emissions saving (g/km) f22 | |||||||
F113.5.4.
Electric energy consumption for externally chargeable hybrid electric vehicles
3.5.4.1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.4.2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.4.3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle fitted with an eco-innovation within the meaning of Article 12 of Regulation (EC) No 443/2009 for M 1 vehicles or Article 12 of Regulation (EU) No 510/2011 for N 1 vehicles: yes/no f23 .
3.5.6.1.
Type/Variant/Version of the baseline vehicle as referred to in Article 5 of Regulation (EU) No 725/2011 for M 1 vehicles or Article 5 of Regulation (EU) No 427/2014 for N 1 vehicles f24 .
3.5.6.2.
Interactions existing between different eco-innovations: yes/no
3.5.6.3.
| Number of the Commission Decision approving the eco-innovation. | |||||||
| Assigned in the Commission Decision approving the eco-innovation. | |||||||
| Under agreement of the type-approval authority, if modelling is applied instead of the type 1 test-cycle, this value shall be the one provided by the modelling methodology. | |||||||
| Sum of the emissions saving of each individual eco-innovation. | |||||||
| Decision approving the eco-innovation f27 | Code of the eco-innovation f28 | 1. CO 2 emissions of the baseline vehicle (g/km) | 2. CO 2 emissions of the eco-innovation vehicle (g/km) | 3. CO 2 emissions of the baseline vehicle under type 1 test-cycle f29 | 4. CO 2 emissions of the eco-innovation vehicle under type 1 test-cycle (= 3.5.1.3) | 5. Usage factor (UF)i.e. temporal share of technology usage in normal operation conditions | CO 2 emissions savings |
|---|---|---|---|---|---|---|---|
| xxxx/201x | |||||||
| Total CO 2 emissions saving (g/km) f30 | |||||||
3.6.
Temperatures permitted by the manufacturer
3.6.1.
Cooling system
3.6.1.1.
Liquid cooling
Maximum temperature at outlet: K
3.6.1.2.
Air cooling
3.6.1.2.1.
Reference point: …
3.6.1.2.2.
Maximum temperature at reference point: K
3.6.2.
Maximum outlet temperature of the inlet intercooler: K
3.6.3.
Maximum exhaust temperature at the point in the exhaust pipe(s) adjacent to the outer flange(s) of the exhaust manifold: K
3.6.4.
Fuel temperature
Minimum: K
Maximum: K
3.6.5.
Lubricant temperature
Minimum: K
Maximum: K
3.8.
Lubrication system
3.8.1.
Description of the system
3.8.1.1.
Position of the lubricant reservoir:
3.8.1.2.
Feed system (by pump/injection into intake/mixing with fuel, etc.)
3.8.2.
Lubricating pump
3.8.2.1.
Make(s):
3.8.2.2.
Type(s):
3.8.3.
Mixture with fuel
3.8.3.1.
Percentage:
3.8.4.
Oil cooler: yes/no
3.8.4.1.
Drawing(s): …, or
3.8.4.1.1.
Make(s):
3.8.4.1.2.
Type(s):
4.
TRANSMISSIONf31
4.3.
Moment of inertia of engine flywheel:
4.3.1.
Additional moment of inertia with no gear engaged:
4.4.
Clutch(es)
4.4.1.
Maximum torque conversion:
4.5.
Gearbox
4.5.1.
Type (manual/automatic/CVT (continuously variable transmission))
4.6.
Gear ratios
| Gear | Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions) | Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions) | Total gear ratios |
|---|---|---|---|
| Maximum for CVT | |||
| 1 | |||
| 2 | |||
| 3 | |||
| … | |||
| Minimum for CVT |
6.
SUSPENSION
6.6.
Tyres and wheels
6.6.1.
Tyre/wheel combination(s)
6.6.1.1.
Axles
6.6.1.1.1.
Axle 1:
6.6.1.1.1.1.
Tyre size designation
6.6.1.1.2.
Axle 2:
6.6.1.1.2.1.
Tyre size designation
etc.
6.6.2.
Upper and lower limits of rolling radii
6.6.2.1.
Axle 1:
6.6.2.2.
Axle 2:
etc.
6.6.3.
Tyre pressure(s) as recommended by the vehicle manufacturer: kPa
9.
BODYWORK
9.1.
Type of bodywork using the codes defined in Part C of Annex II of Directive 2007/46/EC:
9.10.3.
Seats
9.10.3.1.
Number:
16.
ACCESS TO VEHICLE REPAIR AND MAINTENANCE INFORMATION
16.1.
Address of principal website for access to vehicle repair and maintenance information:
16.1.1.
Date from which it is available (no later than 6 months from the date of type approval):
16.2.
Terms and conditions of access to website referred to in Section 16.1:
16.3.
Format of vehicle repair and maintenance information accessible through website referred to in Section 16.1:
Annotations
Textual amendments
- F1
- F2
- F3
- F4
- F5
- F6
- F7
- F8
- F9
- F10
- F11
- F12
- F13
Footnotes
- f1
-
Delete where not applicable (there are cases where nothing needs to be deleted when more than one entry is applicable).
- f2
-
If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol.?. (e.g. ABC??123??).
- f3
-
Classified according to the definitions listed in Annex II, Section A.
- f4
-
(e) Where there is one version with a normal cab and another with a sleeper cab, both sets of masses and dimensions are to be stated.
- f5
-
The mass of the driver and, if applicable, of the crew member is assessed at 75 kg (subdivided into 68 kg occupant mass and 7 kg luggage mass according to ISO Standard 2416-1992), the fuel tank is filled to 90 % ant the other liquid containing systems (except those for used water) to 100 % of the capacity specified by the manufacturer.
- f6
-
For trailers or semi-trailers, and for vehicles coupled with a trailer or a semi-trailer, which exert a significant vertical load on the coupling device or the fifth wheel, this load, divided by standard acceleration of gravity, is included in the maximum technical permissible mass.
- f7
-
Please fill in here the upper and lower values for each variant.
- f8
-
This figure must be rounded off to the nearest tenth of a millimetre.
- f9
-
Specify the tolerance.
- f10
-
Determined in accordance with the requirements of Annex XX to this Regulation.
- f11
-
Vehicles can be fuelled with both petrol and a gaseous fuel but, where the petrol system is fitted for emergency purposes or starting only and of which the petrol tank cannot contain more than 15 litres of petrol, will be regarded for the test as vehicles which can only run on a gaseous fuel.
- f12
- f13
- f14
-
Determined in accordance with the requirements of Directive 80/1268/EEC.
- f15
-
If applicable.
- f16
-
Delete where not applicable.
- f17
-
Repeat the table for each reference fuel tested.
- f18
-
Expand the table if necessary, using one extra row per eco-innovation.
- f19
-
Number of the Commission Decision approving the eco-innovation.
- f20
-
Assigned in the Commission Decision approving the eco-innovation.
- f21
-
Under agreement of the type-approval authority, if modelling is applied instead of the type 1 test-cycle, this value shall be the one provided by the modelling methodology.
- f22
-
Sum of the emission s saving of each individual eco-innovation.
- f23
-
Delete where not applicable.
- f24
-
If applicable.
- f25
-
Repeat the table for each reference fuel tested.
- f26
-
Expand the table if necessary, using one extra row per eco-innovation.
- f27
-
Number of the Commission Decision approving the eco-innovation.
- f28
-
Assigned in the Commission Decision approving the eco-innovation.
- f29
-
Under agreement of the type-approval authority, if modelling is applied instead of the type 1 test-cycle, this value shall be the one provided by the modelling methodology.
- f30
-
Sum of the emissions saving of each individual eco-innovation.
- f31
-
(v) The specified particulars are to be given for any proposed variants.