Appendix ANNEX III GB type-approval model certificatesF1
United Kingdom
Part 1
GB type-approval certificate relating to the type-approval of a vehicle with regard to pedestrian protection
Part 2
GB type-approval certificate relating to the type-approval of a vehicle with regard to it being fitted with a frontal protection system
Part 3
GB type-approval certificate relating to the type-approval of a frontal protection system to be supplied as a separate technical unit
PART 1
MODEL
(maximum format: A4 (210 × 297 mm))
GB TYPE-APPROVAL CERTIFICATE
Stamp of GB type-approval authority
Communication concerning the:
GB type-approvalf1
extension of GB type-approval,
refusal of GB type-approval,
withdrawal of GB type-approval,
of a type of vehicle with regard to pedestrian protection
with regard to Regulation (EC) No 78/2009 of the European Parliament and of the Council of 14 January 2009 F2as it has effect in domestic law, as last amended by S.I. …./….
last amended by Regulation (EC) No …/…f2
GB type-approval No:
Reason for extension:
SECTION I
0.1.
Make (trade name of manufacturer):
0.2.
Type:
0.2.1.
Commercial name(s) (if available)
0.3.
Means of identification of type, if marked on the vehiclef3:
0.3.1.
Location of that marking:
0.4.
Category of vehicle M1:
0.5.
Name and address of manufacturer:
0.8.
Names and address(es) of assembly plant(s):
0.9.
Name and address of the manufacturer’s representative (if any):
SECTION II
1.
Additional information (where applicable) (see Addendum)
2.
Technical service responsible for carrying out the tests:
3.
Date of test report:
4.
Number of test report:
5.
Remarks (if any) (see Addendum):
6.
Place:
7.
Date:
8.
Signature:
Information package.
Test report.
Addendum to GB type-approval certificate No … concerning the type-approval of a vehicle with regard to pedestrian protection with regard to Regulation (EC) No 78/2009
1.
Additional information
1.1.
Brief description of the vehicle type as regards its structure, dimensions, lines and constituent materials:
1.2.
Site of engine: forward/rear/centralf4
1.3.
Drive: front-wheel/rear-wheel
1.4.
Mass of vehicle submitted for testing (as defined in accordance with point 1.7 of Annex I to Regulation (EC) No 78/2009):
Front axle:
Rear axle:
Total:
1.5.
Test results according to the requirements of Annex I to Regulation (EC) No 78/2009:
1.5.1.
Section 2 test results:
According to the values specified in Section 2 of Annex I to Regulation (EC) No 78/2009. | ||||
For monitoring purposes only. | ||||
| Test | Value recorded | Pass/failf5 | ||
|---|---|---|---|---|
| Lower legform to bumper (where performed) | Bending angle | … … | degrees | |
| Shear displacement | … … | mm | ||
| Acceleration at tibia | … … | g | ||
| Upper legform to bumper (where performed) | Sum of impact forces | … … | kN | |
| Bending moment | … … | Nm | ||
| Upper legform to bonnet leading edge | Sum of impact forces | … … | kN | f6 |
| Bending moment | … … | Nm | ||
| Child/small adult headform (3,5 kg) to bonnet top | HPC values in Zone A (12 results M2) | |||
HPC values in Zone B (6 results ) | ||||
| Adult headform (4,8 kg) to windscreen | HPC values (5 results ) | |||
1.5.2.
Section 3 test results:
According to the values specified in Section 3 of Annex I to Regulation (EC) No 78/2009. | ||||
For monitoring purposes only. | ||||
| Test | Value recorded | Pass/failf7 | ||
|---|---|---|---|---|
| Lower legform to bumper (where performed) | Bending angle | … … | degrees | |
| Shear displacement | … … | mm | ||
| Acceleration at tibia | … … | g | ||
| Upper legform to bumper (where performed) | Sum of impact forces | … … | kN | |
| Bending moment | … … | Nm | ||
| Upper legform to bonnet leading edge | Sum of impact forces | … … | kN | f8 |
| Bending moment | … … | Nm | ||
| Child/small adult headform (3,5 kg) to bonnet top | HPC values (9 results ) | |||
| Adult headform (4,5 kg) to windscreen | HPC values (9 results ) | |||
Remarks: (e.g., valid for left-hand drive and right-hand drive vehicles)
1.5.3.
Section 4 requirements:
PART 2
MODEL
(maximum format: A4 (210 × 297 mm))
GB TYPE-APPROVAL CERTIFICATE
Stamp of GB type-approval authority
Communication concerning the:
GB type-approval
extension of GB type-approval,
refusal of GB type-approval,
withdrawal of GB type-approval,
of a type of a vehicle with regard to it being fitted with a frontal protection system
with regard to Regulation (EC) No 78/2009 of the European Parliament and of the Council of 14 January 2009 F3as it has effect in domestic law, as last amended by S.I. …./….
last amended by Regulation (EC) No …/…
GB type-approval No:
Reason for extension:
SECTION I
0.1.
Make (trade name of manufacturer):
0.2.
Type:
0.2.1.
Commercial name(s) (if available):
0.3.
Means of identification of type, if marked on the vehicle:
0.3.1.
Location of that marking:
0.4.
Category of vehicle :
0.5.
Name and address of manufacturer:
0.7.
Location and method of affixing of the GB type-approval:
0.8.
Address(es) of assembly plant(s):
0.9.
Name and address of the manufacturer’s representative (if any):
SECTION II
1.
Additional information (where applicable): See Addendum
2.
Technical service responsible for carrying out the tests:
3.
Date of test report:
4.
Number of test report:
5.
Remarks (if any): See Addendum
6.
Place:
7.
Date:
8.
Signature:
Information package.
Test report.
Addendum to GB type-approval certificate No … concerning the type-approval of a vehicle with regard to it being fitted with a frontal protection system with regard to Regulation (EC) No 78/2009
1.
Additional information, if any:
2.
Remarks:
3.
Test results according to the requirements of Section 5 of Annex I to Regulation (EC) No 78/2009
| Test | Value recorded | Pass/fail | ||
|---|---|---|---|---|
Lower legform to frontal protection system — three test positions (where performed) | Bending angle | … … | degrees | |
| Shear displacement | … … | mm | ||
| Acceleration at tibia | … … | g | ||
Upper legform to frontal protection system — three test positions (where performed) | Sum of impact forces | … … | kN | |
| Bending moment | … … | Nm | ||
Upper legform to frontal protection system leading edge — three test positions (monitoring only) | Sum of impact forces | … … | kN | |
| Bending moment | Nm | |||
| Child/small adult headform (3,5 kg) to frontal protection system | HPC values (at least three values) | |||
PART 3
MODEL
(maximum format: A4 (210 × 297 mm))
GB TYPE-APPROVAL CERTIFICATE F4(SEPARATE TECHNICAL UNIT)
Stamp of GB type-approval authority
Communication concerning the:
GB type-approval,
extension of GB type-approval,
refusal of GB type-approval,
withdrawal of GB type-approval,
of a type of frontal protection system to be supplied as a separate technical unit
with regard to Regulation (EC) No 78/2009 of the European Parliament and of the Council of 14 January 2009 F5as it has effect in domestic law, as last amended by S.I. …./….
last amended by Regulation (EC) No …/…
GB type-approval No:
Reason for extension:
SECTION I
0.1.
Make (trade name of manufacturer):
0.2.
Type:
0.3.
Means of identification of type if marked on the frontal protection system:
0.3.1.
Location of that marking:
0.5.
Name and address of manufacturer:
0.7.
Location and method of the affixing of the F6GB approval mark:
0.8.
Name(s) and address(es) of assembly plant(s):
0.9.
Name and address of the manufacturer’s representative (if any):
SECTION II
1.
Additional information: See Addendum
2.
Technical service responsible for carrying out the tests:
3.
Date of test report:
4.
Number of test report:
5.
Remarks (if any): See Addendum
6.
Place:
7.
Date:
8.
Signature:
Information package.
Test report.
Addendum to GB type-approval certificate No … concerning the type-approval of a type of frontal protection system to be supplied as a separate technical unit with regard to Regulation (EC) No 78/2009
F71.
Additional information
1.1.
Method of attachment:
1.2.
Assembly and mounting instructions:
1.3.
List of vehicles on which the frontal protection system may be fitted, any usage restrictions and necessary conditions for fitting:
…
2.
Remarks:
3.
Test results according to the requirements of Section 5 of Annex I to Regulation (EC) No 78/2009
| Test | Value recorded | Pass/fail | ||
|---|---|---|---|---|
Lower legform to frontal protection system — three test positions (where performed) | Bending angle | … … | degrees | |
| Shear displacement | … … | mm | ||
| Acceleration at tibia | … … | g | ||
Upper legform to frontal protection system — three test positions (where performed) | Sum of impact forces | … … | kN | |
| Bending moment | … … | Nm | ||
Upper legform to frontal protection system leading edge — three test positions (monitoring only) | Sum of impact forces | … … | kN | |
| Bending moment | Nm | |||
| Child/small adult headform (3,5 kg) to frontal protection system | HPC values (at least three values) | |||
Annotations
Textual amendments
- F1
Words in Annex 3 substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(a)
- F2
Words in Annex 3 Pt. 1 substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(b)
- F3
Words in Annex 3 Pt. 2 substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(b)
- F4
Words in Annex 3 Pt. 3 heading inserted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(d)(i)
- F5
Words in Annex 3 Pt. 3 substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(b)
- F6
Word in Annex 3 Pt. 3 s. 1 substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(d)(ii)
- F7
Annex 3 Pt. 3 s. 2: by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(d)(iii) it is provided that in para. 1.5.1 note (c) after the table the words "Regulation (EU) 631/2020" are substituted (31.12.2022 at 11.00 p.m.) for "[implementing legislation]"
Marginal citations
- M1
As defined in [Article 4 of Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.] [Editorial Note: words in Annex 3 note substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(c)]
- M2
According to [Commission Regulation (EU) 631/2010]. [Editorial Note: words in Annex 3 Pt. 1 Addendum note substituted (31.12.2022 at 11.00 p.m.) by The Road Vehicles and Non-Road Mobile Machinery (Type-Approval) (Amendment and Transitional Provisions) (EU Exit) Regulations 2022 (S.I. 2022/1273), regs. 1(2), 51(6)(e)]
Footnotes
- f1
-
Delete where not applicable.
- f2
-
Insert number of amending Regulation.
- f3
-
If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??).
- f4
-
Delete where not applicable.
- f5
According to the values specified in Section 2 of Annex I to Regulation (EC) No 78/2009.
- f6
For monitoring purposes only.
- f7
According to the values specified in Section 3 of Annex I to Regulation (EC) No 78/2009.
- f8
For monitoring purposes only.
- f9
Provide details of system operation method.
- f10
Provide details of testing completed to verify system.