OpenLegislation

Annex IX

United Kingdom

Original text. Later amendments are not shown.

Annex X to Regulation (EU) 2017/2400 is amended as follows:

  1. (1)

    point 3.4.1 is replaced by the following:

    ‘3.4.1.

    The tyre shall be clearly identifiable in respect to the certificate covering it for the corresponding rolling resistance coefficient.’;

  2. (2)

    in point 3.4.2, the first sentence is replaced by the following:

    ‘The tyre manufacturer shall use the markings affixed to the side wall of the tyre or affix an additional identifier to the tyre.’;

  3. (3)

    Appendix 1 is replaced by the following:

    ‘Appendix 1

    MODEL OF A CERTIFICATE OF A COMPONENT, SEPARATE TECHNICAL UNIT OR SYSTEM

    Maximum format: A4 (210 × 297 mm)

    CERTIFICATE ON CO2 EMISSIONS AND FUEL CONSUMPTION RELATED PROPERTIES OF A TYRE FAMILY

    “delete as appropriate”

    Communication concerning:

    • grantingf1

    • extension

    • refusal

    • withdrawal

    		Administration stamp

    of a certificate on CO2 emission and fuel consumption related properties of a tyre family in accordance with Commission Regulation (EU) 2017/2400, as amended by Commission Regulation (EU) 2019/318

    Certification number: …

    Hash: …

    Reason for extension: …

    1.

    Manufacturer's name and address: …

    2.

    If applicable, name and address of manufacturer's representative: …

    3.

    Brand name/trade mark: …

    4.

    Tyre type description: …

    1. (a)

      Manufacturer's name …

    2. (b)

      Brand name or trade mark

    3. (c)

      Tyre class (in accordance with Regulation (EC) No 661/2009) …

    4. (d)

      Tyre-size designation …

    5. (e)

      Tyre structure (diagonal (bias-ply); radial) …

    6. (f)

      Category of use (normal tyre, snow tyre, special use tyre) …

    7. (g)

      Speed category (categories) …

    8. (h)

      Load-capacity index (indices) …

    9. (i)

      Trade description/commercial name …

    10. (j)

      Declared tyre rolling resistance coefficient …

    5.

    Tyre identification code(s) and technology(ies) used to provide identification code(s), if applicable:

    Technology:Code:
    ……

    6.

    Technical Service and, where appropriate, test laboratory approved for purposes of approval or of verification of conformity tests: …

    7.

    Declared values:

    1. 7.1.

      declared rolling resistance level of the tyre (in N/kN rounded to the first decimal place, in accordance with ISO 80000-1 Appendix B, section B.3, rule B (example 1))

      Cr, … [N/kN]

    2. 7.2.

      tyre test load in accordance with Regulation (EC) No 1222/2009 Annex I part A (85 % of single load, or 85 % of maximum load capacity for single application specified in applicable tyre standards manuals if not marked on tyre.)

      FZTYRE … [N]

    3. 7.3.

      Alignment equation: …

    8.

    Any remarks: …

    9.

    Place: …

    10.

    Date: …

    11.

    Signature: …

    12.

    Annexed to this communication are: …’;

  4. (4)

    Appendix 2 is amended as follows:

    1. (a)

      SECTION I is amended as follows:

      points 0.14 and 0.16 are deleted;

    2. (b)

      SECTION II is amended as follows:

      1. (i)

        point 4 is replaced by the following:

        ‘4.

        Date of test report:’;

      2. (ii)

        point 8.4 is replaced by the following:

        ‘8.4.

        Alignment equation:’;

      3. (iii)

        the following point is inserted:

        ‘8.5.

        Rolling resistance level of the tyre (in N/kN rounded to the first decimal place, in accordance with ISO80000-1 Appendix B, section B.3, rule B (example 1)) Cr,aligned … [N/kN]’;

  5. (5)

    Appendix 3 is amended as follows:

    1. (a)

      the title is replaced by the following:

      ‘ Input parameters for the simulation tool ’;

    2. (b)

      in Definitions, point (1) is replaced by the following:

      (1) “Parameter ID”

    3. ‘Unique identifier as used in the simulation tool for a specific input parameter or set of input data’;

    4. (c)

      in Table 1, the third row ‘TechnicalReportId’ below the title and the last row are replaced by the following:

      ‘

      CertificationNumberP232token
      DimensionP108string[-]Allowed values (non-exhaustive): “9.00 R20”, “9 R22.5”, “9.5 R17.5”, “10 R17.5”, “10 R22.5”, “10.00 R20”, “11 R22.5”, “11.00 R20”, “11.00 R22.5”, “12 R22.5”, “12.00 R20”, “12.00 R24”, “12.5 R20”, “13 R22.5”, “14.00 R20”, “14.5 R20”, “16.00 R20”, “205/75 R17.5”, “215/75 R17.5”, “225/70 R17.5”, “225/75 R17.5”, “235/75 R17.5”, “245/70 R17.5”, “245/70 R19.5”, “255/70 R22.5”, “265/70 R17.5”, “265/70 R19.5”, “275/70 R22.5”, “275/80 R22.5”, “285/60 R22.5”, “285/70 R19.5”, “295/55 R22.5”, “295/60 R22.5”, “295/80 R22.5”, “305/60 R22.5”, “305/70 R19.5”, “305/70 R22.5”, “305/75 R24.5”, “315/45 R22.5”, “315/60 R22.5”, “315/70 R22.5”, “315/80 R22.5”, “325/95 R24”, “335/80 R20”, “355/50 R22.5”, “365/70 R22.5”, “365/80 R20”, “365/85 R20”, “375/45 R22.5”, “375/50 R22.5”, “375/90 R22.5”, “385/55 R22.5”, “385/65 R22.5”, “395/85 R20”, “425/65 R22.5”, “495/45 R22.5”, “525/65 R20.5”

      ’

  6. (6)

    in Appendix 4, point 2.1 is replaced by the following:

    ‘1.1.

    Certification number for tyres shall comprise the following:

    eX*YYYY/YYYY*ZZZZ/ZZZZ*T*0000*00

    Section 1Section 2Section 3Additional letter to section 3Section 4Section 5
    Indication of country issuing the certificateHDV CO2 certification Regulation (2017/2400)Latest amending Regulation (ZZZZ/ZZZZ)T = TyreBase certification number 0000Extension 00

    ’

Annotations

Footnotes

f1

“delete as appropriate”