OpenLegislation

Schedule 4 (Annex IV to Directive 97/68/EC)

Original text. Later amendments are not shown.

NON-ROAD MOBILE MACHINERY REFERENCE FUELf1

Note: Key properties for engine performance/exhaust emissions are highlighted.

Limits and unitsf2Test method

Note 1: If it is required to calculate thermal efficiency of an engine or vehicle, the calorific value of the fuel can be calculated from:

Specificenergy(calorificvalue)(net)MJ/kg=(46.423-8.792.d2+3.17.d)×(1-(x+y+s))+9.42.s-2.499.x.

where:

d
  • is the density at 288 K (15°C)

  • x
  • is the proportion by mass of water (%/100)

  • y
  • is the proportion by mass of ash (%/100)

  • s
  • is the proportion by mass of sulphur (%/100).

  • Note 2: The values quoted in the specification are ‘true values’. In establishment of their limit values the terms of ASTMD D 3244 ‘Defining a basis for petroleum produce quality disputes’ have been applied and in fixing minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility).

    Notwithstanding this measure, which is necessary for statistical reasons, the manufactuer of fuel should nevertheless aim at a zero value where the stipulated maximum value is 2R and the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify the question as to whether a fuel meets the requirements of the specifications, the terms of ASTM D 3244 should be applied.

    Note 3: The figures quoted show the evaporated quantities (percentage recovered + percentage loss).

    Note 4: The range of cetane is not in accordance with the requirement of a minimum range of 4R. However, in cases of dispute between fuel supplier and fuel user, the terms in ASTM D 3244 can be used to resolve such disputes provided replicate measurements, of sufficient number to achieve the necessary precision, are made in preference to single determinations.

    Note 5: Even though oxidation stability is controlled, it is likely that shelf life will be limited. Advice should be sought from the supplier as to storage conditions and life.

    Note 6: This fuel should be based straight run and cracked hydrocarbon distillate components only; desulphurization is allowed. It must not contain any metallic additives or cetane improver additives.

    Note 7: Lower values are permitted, in which case the cetane number of reference fuel used is to be reported.

    Note 8: Higher values are permitted, in which case the sulphur content of the reference fuel used is to be reported.

    Note 9: To be kept under constant review in the light of trends in the markets. For the purpose of the initial approval of an engine with no exhaust gas after treatement on request of the applicant a 0.050% mass sulphur minimum is permissible, in which case the measured particulate level must be corrected upward to the average value that is nominally specified for fuel sulphur content (0.150% mass) per the equation below:

    PTadj=PT+[SFC×0.0917×(NSLF-FSF)]

    where:

    PTadj
  • adjusted PT value (g/kWh)

  • PT
  • measured weighted specific emission value for particulate emission (g/kWh)

  • SFC
  • weighted specific fuel consumption (g/kWh) calculated according to the formula as below

  • NSLF
  • average of the nominal specification of sulphur content mass fraction (ie 0.15%/100)

  • FSF
  • fuel sulphur content mass fraction (%/100)

  • Equation for the calculation of the weighted specific fuel consumption:

    SFC=∑i=1nGFUEL,ixWFi∑i=1nPixWFi

    where:

    Pi= Pm,i+ PAE,i

    For the purpose of conformity of production assessments in accordance with section 5.3.2 of Annex I, the requirements must be met using reference fuel with a sulphur content which complies with the minimum/maximum level of 0.1/0.2% mass.

    Note 10: Higher values are permitted up to 855 kg/m3, in which case the density of the reference fuel used is to be reported. For the purpose of conformity of production assessments in accordance with section 5.3.2 of Annex I, the requirements must be met using reference fuel which complies with the minimum/maximum level of 835/845 kg/m3.

    Note 11: All fuel characteristics and limit values are to be kept under review in light of trends in the markets.

    Note 12: To be replaced by EN/ISO 6245 with effect of the date of implementation.

    Cetane numberf3

    minimum 45f4

    maximum 50

    ISO 5165
    Density at 15°C

    minimum 835 kg/m3

    maximum 845 kg/m3f5

    ISO 3675, ASTM D4052
    Distillationf6−95% pointMaximum 370°CISO 3405
    Viscosity at 40°C

    Minimum 2.5 mm2/s

    Maximum 3.5mm2/s

    ISO 3104
    Sulphur content

    Minimum 0.1% massf7

    Maximum 0.2% massf8

    ISO 8754, EN 24260
    Flash pointMinimum 55°CISO 2719
    CFPP

    Minimum −

    Maximum + 5°C

    EN 116
    Copper corrosionMaximum 1ISO 2160
    Conradson carbon residue (10% DR)Maximum 0.3% massISO 10370
    Ash contentMaximum 0.01% massASTM D 482f9
    Water contentMaximum 0.05% massASTM D 95, D 1744
    Neutralization (strong acid) numberMinimum 0.20 mg KOH/g
    Oxidation stabilityf10Maximum 2.5 mg/100 mlASTM D2274
    Additivesf11

    Annotations

    Footnotes

    f1

    Note 1: If it is required to calculate thermal efficiency of an engine or vehicle, the calorific value of the fuel can be calculated from:

    Specificenergy(calorificvalue)(net)MJ/kg=(46.423-8.792.d2+3.17.d)×(1-(x+y+s))+9.42.s-2.499.x.

    where:

    d
  • is the density at 288 K (15°C)

  • x
  • is the proportion by mass of water (%/100)

  • y
  • is the proportion by mass of ash (%/100)

  • s
  • is the proportion by mass of sulphur (%/100).

  • f2

    Note 2: The values quoted in the specification are ‘true values’. In establishment of their limit values the terms of ASTMD D 3244 ‘Defining a basis for petroleum produce quality disputes’ have been applied and in fixing minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility).

    Notwithstanding this measure, which is necessary for statistical reasons, the manufactuer of fuel should nevertheless aim at a zero value where the stipulated maximum value is 2R and the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify the question as to whether a fuel meets the requirements of the specifications, the terms of ASTM D 3244 should be applied.

    f3

    Note 4: The range of cetane is not in accordance with the requirement of a minimum range of 4R. However, in cases of dispute between fuel supplier and fuel user, the terms in ASTM D 3244 can be used to resolve such disputes provided replicate measurements, of sufficient number to achieve the necessary precision, are made in preference to single determinations.

    f4

    Note 7: Lower values are permitted, in which case the cetane number of reference fuel used is to be reported.

    f5

    Note 10: Higher values are permitted up to 855 kg/m3, in which case the density of the reference fuel used is to be reported. For the purpose of conformity of production assessments in accordance with section 5.3.2 of Annex I, the requirements must be met using reference fuel which complies with the minimum/maximum level of 835/845 kg/m3.

    f6

    Note 3: The figures quoted show the evaporated quantities (percentage recovered + percentage loss).

    f7

    Note 9: To be kept under constant review in the light of trends in the markets. For the purpose of the initial approval of an engine with no exhaust gas after treatement on request of the applicant a 0.050% mass sulphur minimum is permissible, in which case the measured particulate level must be corrected upward to the average value that is nominally specified for fuel sulphur content (0.150% mass) per the equation below:

    PTadj=PT+[SFC×0.0917×(NSLF-FSF)]

    where:

    PTadj
  • adjusted PT value (g/kWh)

  • PT
  • measured weighted specific emission value for particulate emission (g/kWh)

  • SFC
  • weighted specific fuel consumption (g/kWh) calculated according to the formula as below

  • NSLF
  • average of the nominal specification of sulphur content mass fraction (ie 0.15%/100)

  • FSF
  • fuel sulphur content mass fraction (%/100)

  • Equation for the calculation of the weighted specific fuel consumption:

    SFC=∑i=1nGFUEL,ixWFi∑i=1nPixWFi

    where:

    Pi= Pm,i+ PAE,i

    For the purpose of conformity of production assessments in accordance with section 5.3.2 of Annex I, the requirements must be met using reference fuel with a sulphur content which complies with the minimum/maximum level of 0.1/0.2% mass.

    f8

    Note 8: Higher values are permitted, in which case the sulphur content of the reference fuel used is to be reported.

    f9

    Note 12: To be replaced by EN/ISO 6245 with effect of the date of implementation.

    f10

    Note 5: Even though oxidation stability is controlled, it is likely that shelf life will be limited. Advice should be sought from the supplier as to storage conditions and life.

    f11

    Note 6: This fuel should be based straight run and cracked hydrocarbon distillate components only; desulphurization is allowed. It must not contain any metallic additives or cetane improver additives.